Airmar MMC-8G-L Garmin 8-Pin Low CHIRP Mix-N-Match CableModel: MMC-8G-LSpecifications Cable-Length 1 m (3 feet) Display Connector 8G Mix and Match Series 12-Pin Chirp Sensor Connector MMC

Read more less

Airmar MMC-8G Garmin 8-Pin CHIRP Mix-N-Match CableModel: MMC-8GSpecifications Cable-Length 1 m (3 feet) Display Connector 8G Mix and Match Series 12-Pin Chirp Sensor Connector MMC

Read more less

Airmar MMC-12G-L Garmin 12-pin Single Low CHIRP Mix-N-Match CableModel: MMC-12G-LAirmar's Garmin Mix & Match CableSpecifications Cable-Length 1 m (3 feet) Display Connector 12G Mix and Match Series 12-Pin Chirp Sensor Connector MMC

Read more less

Airmar MMC-12G Garmin 12-pin CHIRP Mix-N-Match CableModel: MMC-12GMany CHIRP transducers are now made as Mix and Match models. These versions use a common base transducer with an attached 9-meter cable, plus an interchangeable short (1-meter) brand-specific adapter cable. Both parts are needed for an installation. The base transducer can be used with any brand of sounder by selecting the appropriate adapter.The permanently-attached 9-meter transducer cable ends in an Airmar 12-pin female connector. This cable is run up through the boat to the equipment location. The short adapter cable has an Airmar 12-pin male connector at one end, to connect to the transducer cable, and a brand-specific connector at the other end to connect to the sounder or display.CHIRP Mix and Match cables cannot be used with 600W or 1kW conventional transducers.Specifications Cable-Length 1 m (3') Display Connector 12G Mix and Match Series 12-Pin Chirp Sensor Connector MMC

Read more less

Airmar MMC-12F Furuno 12-pin CHIRP Mix-N-Match CableModel: MMC-12FSpecifications Cable-Length 1 m (3 feet) Display Connector 12F Mix and Match Series 12-Pin Chirp Sensor Connector MMC

Read more less

Airmar MMC-11R-LDB Raymarine 11- Pin Low/Dual Band CHIRP Mix-N-Match CableModel: MMC-11R-LDBSpecifications Cable-Length 1 m (3 feet) Display Connector 11R Mix and Match Series 12-Pin Chirp Sensor Connector MMC

Read more less

Airmar MMC-11R-HM Raymarine 11-Pin High/Medium CHIRP Mix-N-Match CableModel: MMC-11R-HMSpecifications Cable-Length 1 m (3 feet) Display Connector 11R Mix and Match Series 12-Pin Chirp Sensor Connector MMC

Read more less

Airmar Mix-N-Match Cable, 12-Pin Chirp Series, with Furuno 10-pin Low Connector - 1mModel: MMC-10F-LSpecifications Cable-Length 1 m (3 feet) Display Connector 10F Mix and Match Series 12-Pin Chirp Sensor Connector MMC

Read more less

Airmar MMC-10F-HM Furuno 10-Pin High/Medium CHIRP Mix-N-Match CableModel: MMC-10F-HMSpecifications Cable-Length 1 m (3 feet) Display Connector 10F Mix and Match Series 12-Pin Chirp Sensor Connector MMC

Read more less

Airmar Mix-N-Match Cable, 12-Pin Chirp Series, with Bare Wires - 1mMFG #33-1359-01Model: MMC-0Airmar Part #MMC-0 Mix-N-Match Cable, 12-Pin Chirp Series, with Bare Wires - 1mSpecifications Cable-Length 1 m (3 feet) Display Connector 0 Mix and Match Series 12-Pin Chirp Sensor Connector MMC

Read more less

MM-HB Mix & Match™ Cable 5-Pin 600W Series with Humminbird #9 Connector - 9MSpecifications: Sensor Connector: MM Display Connector: HB Mix and Match Series: 5-Pin 600 Watt Country of Origin: USA Cable-Length: 9 m (30') Specifications: Type: Adapters Box Dimensions: 1"H x 6"W x 6"L WT: 0.33 lbs UPC: 801769003772

Read more less

Mix & Match Cable for Raymarine 600W Non-CHIRP Transducers - 9mMix and Match 600W transducers are made as a common base transducer with a short (2m) cable attached, plus an interchangeable longer (8m) brand-specific adapter cable. The short pigtail attached to the transducer ends in an Airmar 5-pin male connector. The adapter cables have a matching Airmar 5-pin female connector at one end and the correct connector for a specific electronics brand at the other end.Both parts are needed for installation. If the user changes equipment brand later, the transducer can be left in place and the adapter cable replaced.*600W Mix and Match cables cannot be used with 1kw transducers or CHIRP transducers.Features: 600W For Raymarine 600W equipment Specifications: Type: Adapters Box Dimensions: 2"H x 8"W x 8"L WT: 1.31 lbs UPC: 801769003734

Read more less

MM-9N Mix & Match Cable for Simrad XSONIC Non-CHIRP TransducersMix and Match 600W transducers are made as a common base transducer with a short (2m) cable attached, plus an interchangeable longer (8m) brand-specific adapter cable. The short pigtail attached to the transducer ends in an Airmar 5-pin male connector. The adapter cables have a matching Airmar 5-pin female connector at one end and the correct connector for a specific electronics brand at the other end.Both parts are needed for installation. If the user changes equipment brand later, the transducer can be left in place and the adapter cable replaced.*600W Mix and Match cables cannot be used with 1kw transducers or CHIRP transducers.Features: Connector: 9-pin, Depth only Fits: HDS Carbon, evo 3 This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns. Specifications: Type: Adapters Box Dimensions: 2"H x 8"W x 8"L WT: 1.3 lbs UPC: 801769003321

Read more less

Furuno 10-Pin Mix & Match Cable for 600W Non-CHIRP TransducersMix and Match 600W transducers are made as a common base transducer with a short (2m) cable attached, plus an interchangeable longer (8m) brand-specific adapter cable. The short pigtail attached to the transducer ends in an Airmar 5-pin male connector. The adapter cables have a matching Airmar 5-pin female connector at one end and the correct connector for a specific electronics brand at the other end.Both parts are needed for installation. If the user changes equipment brand later, the transducer can be left in place and the adapter cable replaced.*600W Mix and Match cables cannot be used with 1kw transducers or CHIRP transducers.Features: 10-Pin For Furuno 10-Pin equipment Specifications: Type: Adapters Box Dimensions: 2"H x 7"W x 7"L WT: 1.2 lbs UPC: 801769003611

Read more less

MM-8G Mix & Match Cable for 600W Non-CHIRP TransducersMix and Match 600W transducers are made as a common base transducer with a short (2m) cable attached, plus an interchangeable longer (8m) brand-specific adapter cable.The short pigtail attached to the transducer ends in an Airmar 5-pin female connector. The adapter cables have a matching Airmar 5-pin male connector (shown below) at one end and the correct connector for a specific brand of electronics at the other end.Both parts are needed for installation. If the user changes equipment brand at some later time, the transducer can be left in place and the adapter cable replaced.Mix and Match 600W transducers include the B117, B45, B60, P319, P66*, P79, SS505, and SS60. (* not all models)A 12m (40') extension cable (part MM-5P-5P) is available with one male and one female 5-pin connector.Note that 600W Mix and Match cables cannot be used with 1kw transducers.This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns. Specifications: Type: Adapters Box Dimensions: 2"H x 8"W x 8"L WT: 1.25 lbs UPC: 801769003048

Read more less

Airmar High Speed fairing Block with Hardware for B45Model: 33-509-01B45 High Speed Fairing Block and hardware (33-443-01).Dimensions: 13.75 x 2.56 in x 2.94 in TallWhat's in the Box: fairing block Hardware 33-443-01"

Read more less

164WR-3 Double Handle Transducer WrenchTransducer wrenches are available for all bronze low profile transducers. They are used to facilitate holding of the transducer and tightening of the hull nut. Wrenches are constructed of 3/16" thick mild steel. They can easily be bent or modified to accommodate challenging installation locations. For use with: B164 SS164 B175C SS264 Specifications: Type: Tools Box Dimensions: 5"H x 6"W x 7"L WT: 1.1 lbs

Read more less

175WR-4 Transducer Housing WrenchA single-handed wrench that holds the main thru-hull housing via the 'wrench flats' on the top of the housing to facilitate tightening of the hull nut. Use wrench 164WR-2 or 164WR-3 for the hull nut.For use with: B164 B175 SS164 SS264 IMPORTANT: the design of the housing for these transducers changed slightly in June 2012. This wrench is for the newer design and has an internal width of 2-3/4". If you need a wrench for the older designs then use the 164WR-4 instead, with an internal width of 2-7/16". Specifications: Type: Tools Box Dimensions: 1"H x 5"W x 10"L WT: 0.6 lbs

Read more less

164WR-2 Transducer Hull Nut WrenchA single-handed wrench to tighten the hull nut on B164, SS164 and SS264 housings.You can use wrench 164WR-4 to brace the housing when using this wrench.For use with: B164 SS164 SS264 Specifications: Type: Tools Box Dimensions: 1"H x 6"W x 11"L WT: 0.85 lbs

Read more less

Airmar Single Arm WrenchModel: 164WR-2Single arm wrench for use with Airmar B164 and B175 series transducers

Read more less

164WR-1 Crows Foot Transducer WrenchTransducer wrenches are available for all bronze low profile transducers. They are used to facilitate holding of the transducer and tightening of the hull nut. Wrenches are constructed of 3/16" thick mild steel. They can easily be bent or modified to accommodate challenging installation locations. For use with: B164 SS164 B175C SS164 Specifications: Type: Tools Box Dimensions: 1"H x 6"W x 7"L WT: 0.95 lbs

Read more less

60WR-2 Transducer Hull Nut WrenchA single-handed wrench to tighten the hull nut on 2" bronze and stainless steel housings. You can use wrench 60WR-4 to brace the housing when using this wrench.For use with: B60 SS60 Specifications: Type: Tools Box Dimensions: 1"H x 4"W x 9"L WT: 0.56 lbs

Read more less

75WR-2 Transducer Hull Nut WrenchA single-handed wrench to tighten the hull nut on bronze and stainless steel housings. You can use wrench 75WR-4 to brace the housing when using this wrench.For use with: B75 SS75 Specifications: Type: Tools Box Dimensions: 1"H x 5"W x 9"L WT: 0.65 lbs

Read more less

10-Conductor In-Line Cable Splice - IP67Airmar CHIRP transducers are made with cables ending in a bare wire connection. Some sounders have internal terminal blocks to which these bare wires can be connected, but many CHIRP fishfinders and sounders use brand-specific connectors.Gemeco has introduced a new line of in-line splices that can be used to connect CHIRP transducers to the correct connector for a given application. These splices are available in two models, one for wires with up to 6 conductors and one for wires with up to 10 conductors. Both models have waterproof gland fittings rated to IP67. A 1.3mm hex-head wrench is included. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns. Specifications: Type: Misc Box Dimensions: 1"H x 1"W x 5"L WT: 0.2 lbs

Read more less

117WR-2 Transducer Hull Nut WrenchA single-handed wrench to tighten the hull nut on 2" bronze and stainless steel housings.You can use wrench 117WR-4 to brace the housing when using this wrench.For use with: B117 B150 B744V B744VL B765C SS555 Specifications: Type: Tools Box Dimensions: 1"H x 4"W x 9"L WT: 0.6 lbs

Read more less

Airmar Single Arm WrenchModel: 164WR-2Single arm wrench for use with Airmar B164 and B175 series transducers

Read more less

Spares kit for S800 and ST800/ Contains all wearing parts in the paddlewheel and blankign plug. 1 - paddlewheel and shaft 2 - O-rings 1 - valve sleeve 1 - retaining ring Note: Not the same as ST600.

Read more less

75WR-4 Transducer Housing WrenchA single-handed wrench that holds the main thru-hull housing via the 'wrench flats' on the side of the housing to facilitate tightening of the hull nut. Use wrench 75WR-2 or 75WR-3 for the hull nut.For use with: B75 SS75 Specifications: Type: Tools Box Dimensions: 1"H x 5"W x 10"L WT: 0.6 lbs

Read more less

75WR-1 Crows Foot Transducer WrenchTransducer wrenches are available for all bronze low profile transducers. They are used to facilitate holding of the transducer and tightening of the hull nut. Wrenches are constructed of 3/16" thick mild steel. They can easily be bent or modified to accommodate challenging installation locations. For use with: B75 SS75 Specifications: Type: Tools Box Dimensions: 1"H x 4"W x 5"L WT: 0.55 lbs

Read more less

60WR-4 Transducer Housing WrenchA single-handed wrench that holds the main thru-hull housing via the 'wrench flats' on the side of the housing to facilitate tightening of the hull nut.Use wrench 60WR-2 or 60WR-3 for the hull nut.For use with: B60 SS60 Specifications: Type: Tools Box Dimensions: 0"H x 6"W x 9"L WT: 0.51 lbs

Read more less

60WR-1 Crows Foot Transducer WrenchTransducer wrenches are available for all bronze low profile transducers. They are used to facilitate holding of the transducer and tightening of the hull nut. Wrenches are constructed of 3/16" thick mild steel. They can easily be bent or modified to accommodate challenging installation locations. For use with: SS60 B60 Specifications: Type: Tools Box Dimensions: 1"H x 4"W x 5"L WT: 0.5 lbs

Read more less

117WR-4 Transducer Housing WrenchA single-handed wrench that holds the main thru-hull housing via the 'wrench flats' on the side of the housing to facilitate tightening of the hull nut. For 2" bronze and stainless steel housings (P617V, B617V, SS617V).Use wrench 117WR-2 or 117WR-3 for the hull nut.*Note that this wrench will not fit on the CA500 camera housing. Specifications: Type: Tools Box Dimensions: 1"H x 3"W x 8"L WT: 0.45 lbs

Read more less

Replacement speed insert for B744V and B66V housings.

Read more less

AIRMAR 33-483-01 B744VL Blanking Plug Assembly

Read more less