FREE SHIPPING ON ORDERS OVER $100.0 Dollars!

  • Sale -$2.00 Xanigo Marine Mold Mildew Stain Remover - 16oz [XMRM16]

    Xanigo Marine Xanigo Marine Mold Mildew Stain Remover - 16oz [XMRM16]

    Mold & Mildew Stain Remover - 16ozSay goodbye to stubborn mold and mildew stains with Xanigo Marine’s Mold & Mildew Stain Remover! This powerful formula is easy to use and is the perfect solution for removing mold and mildew stains from boat tops, vinyl cushions, chairs, canopies, and more. Its versatile formula can also be used on rubber fenders, fiberglass, caulk, tile, grout, shower stalls, sinks, counters, and other surfaces that may be prone to mold and mildew.Simply spray the product onto a cool substrate, let it soak for a few minutes, and watch the mold and mildew disappear. To ensure the best results, avoid using it in direct sunlight.After removing it, make sure to PREVENT the mold from coming back with Xanigo Marine’s Mold & Mildew Preventer.Specifications:Bottle Size: 16 ouncesSTEP 1: Remove Mold & Mildew with Xanigo Marine's Mold & Mildew Stain RemoverXanigo Marin’s Mold & Mildew Stain Remover is a very effective way to remove mold and mildew. Being a harsh chemical, it should only be used once to remove the mold, and then the preventer should be applied to prevent the mold from coming back. Liberally apply the Mold & Mildew Stain Remover to the seats. Let it sit for 60-90 seconds but do not let it dry. An additional solution may need to be applied— keep it wet. Agitate in a circular motion with a brush to remove the mold from the pores. Rinse thoroughly with clean water.STEP 2: Neutralize the RemoverAfter rinsing the remover off with fresh water, it's important to make sure any leftover remover is neutralized so it doesn't dry out vinyl or impact stitching. Spray the Waterless Wash onto the seats and wipe it in with a microfiber cloth to neutralize the chemicals in the remover.STEP 3: Prevent Mold & Mildew with Xanigo Marine's Mold & Mildew PreventerWith just one application, a boat will be protected against mold and mildew for up to 90 days. The preventer creates a covalent bond with the surface on which it is applied. Users can apply this to almost any marine surface, including vinyl seats, life jackets, canvas, ropes, compartments, live wells, bilges, patio furniture, and other areas of high moisture.Spray the Mold & Mildew Preventer onto a clean, dry surface and spread it evenly with a microfiber cloth. Remember to spread, not wipe off.STEP 4: Maintain Seats with Xanigo Marine's Waterless WashKeep the boat clean between mold prevention applications without the use of harsh chemicals or wasting water. Spray the Waterless Wash onto the seats, let it sit for 15-20 seconds, and wipe it off with a microfiber cloth. Remove sunscreen (a major food source for mold) and leave a refreshing smell without impacting the protective layer created by the mold & mildew preventer.Also, a great way to shine up a gel coat quickly! Specifications: Type: Mildew & Moisture Box Dimensions: 3"H x 3"W x 8"L WT: 1.2 lbs UPC: 860007772771

    Read more

    $26.99 $24.99

  • Sale -$2.00 Xanigo Marine Mold Mildew Stain Remover - 32oz [XMRM32]

    Xanigo Marine Xanigo Marine Mold Mildew Stain Remover - 32oz [XMRM32]

    Mold & Mildew Stain Remover - 32ozSay goodbye to stubborn mold and mildew stains with Xanigo Marine’s Mold & Mildew Stain Remover! This powerful formula is easy to use and is the perfect solution for removing mold and mildew stains from boat tops, vinyl cushions, chairs, canopies, and more. Its versatile formula can also be used on rubber fenders, fiberglass, caulk, tile, grout, shower stalls, sinks, counters, and other surfaces that may be prone to mold and mildew.Simply spray the product onto a cool substrate, let it soak for a few minutes, and watch the mold and mildew disappear. To ensure the best results, avoid using it in direct sunlight.After removing it, make sure to PREVENT the mold from coming back with Xanigo Marine’s Mold & Mildew Preventer.Specifications:Bottle Size: 32 ouncesSTEP 1: Remove Mold & Mildew with Xanigo Marine's Mold & Mildew Stain RemoverXanigo Marin’s Mold & Mildew Stain Remover is a very effective way to remove mold and mildew. Being a harsh chemical, it should only be used once to remove the mold, and then the preventer should be applied to prevent the mold from coming back. Liberally apply the Mold & Mildew Stain Remover to the seats. Let it sit for 60-90 seconds but do not let it dry. An additional solution may need to be applied— keep it wet. Agitate in a circular motion with a brush to remove the mold from the pores. Rinse thoroughly with clean water.STEP 2: Neutralize the RemoverAfter rinsing the remover off with fresh water, it's important to make sure any leftover remover is neutralized so it doesn't dry out vinyl or impact stitching. Spray the Waterless Wash onto the seats and wipe it in with a microfiber cloth to neutralize the chemicals in the remover.STEP 3: Prevent Mold & Mildew with Xanigo Marine's Mold & Mildew PreventerWith just one application, a boat will be protected against mold and mildew for up to 90 days. The preventer creates a covalent bond with the surface on which it is applied. Users can apply this to almost any marine surface, including vinyl seats, life jackets, canvas, ropes, compartments, live wells, bilges, patio furniture, and other areas of high moisture.Spray the Mold & Mildew Preventer onto a clean, dry surface and spread it evenly with a microfiber cloth. Remember to spread, not wipe off.STEP 4: Maintain Seats with Xanigo Marine's Waterless WashKeep the boat clean between mold prevention applications without the use of harsh chemicals or wasting water. Spray the Waterless Wash onto the seats, let it sit for 15-20 seconds, and wipe it off with a microfiber cloth. Remove sunscreen (a major food source for mold) and leave a refreshing smell without impacting the protective layer created by the mold & mildew preventer.Also, a great way to shine up a gel coat quickly! Specifications: Type: Mildew & Moisture Box Dimensions: 4"H x 4"W x 10"L WT: 2.5 lbs UPC: 860007772788 Quick Guide (pdf)

    Read more

    $47.99 $45.99

  • Sale -$2.00 Davis Rocker Stopper Boat Stabilizer [352]

    Davis Instruments Davis Rocker Stopper Boat Stabilizer [352]

    Rocker Stopper Boat StabilizerRocker Stoppers help dampen the rocking motion of boats at anchor. Simply tie Rocker Stoppers approximately 44 cm (18″) apart, making a string of them, with a 5-10 pound weight attached at the bottom of the string. Hang one string off each side of the boat. Just four units per side are what it takes on most boats to 36′. Be sure you hang them where they will always be underwater. Many people use mushroom anchors with their Rocker Stoppers because this type of weight nests well inside the last Rocker Stopper in your string. Use 10 mm (3/8″) braided nylon or 3-stranded nylon line.Use without a weight (or with a reduced weight) for drift fishing. Rocker Stoppers will slow down drift substantially. They are also great to use at the end of a dock to stabilize the tip from rocking. Rocker Stoppers nest together and each one is 33 cm (14″) in diameter.It’s lightweight and molded of high impact, virtually indestructible styrene. Can be deployed or retrieved in seconds. Unaffected by saltwater and cannot affect the sides of your boat. Units are made to “nest” within each other, so storage is a breeze.A Number of Rocker Stopper Units Needed on Each Side of the Boat (Sail or Power): Up to 26 feet (0-8 m) – 3 27 to 36 feet (8-11 m) – 4 37 to 42 feet (11-13 m) – 5 43 to 50 feet (13-15 m) – 8 Quick Guide (pdf)

    Read more

    $19.99 $17.99

  • Sale -$4.00 Minn Kota MKP-32 Weedless Wedge 2 Prop [1865017]

    Minn Kota Minn Kota MKP-32 Weedless Wedge 2 Prop [1865017]

    Weedless Wedge™ 2 Props (MKP-32) Minn Kota®s exclusive prop is the only of its kind that is 100 percent weedless. Unique design features swept-back and flared blades to "wedge" weeds away while conserving battery power. Moves through heavy vegetation, even at slow speeds. Motor Diameter:   3 - 5 / 8"Prop Nut Kit:        "A" Compatible with Motor Models With Serial Number Prefix "WW"55AT, 55AT/H, 70AT, TERROVA 55, TERROVA 55/US2, TERROVA 55/AP, TERROVA 55/AP/US2, MAX 55/SC, MAX 55, MAX 55/SC/H, MAX 70, MAX 70/H/3X,MAX 70/SC, MAX 70/SC/H, MAX 70/US, MAX 55T, MAX 70T, 50PD v2, 55PD v2, 55PD V2/US2, 55PD V2/AP, 55PD V2/AP/US2, 65PD V2, 70PD V2, 70PD V2/AP ,70PD V2/AP/US2, 54PD V2 pontoon, 68PD V2 pontoon, 55HC pontoon, 70HC pontoon, 50PD, 55PD/AP, 55PD/AP/US, 55PD/US, 65PD, 70PD, 70PD/AP, 70PD/US, 70PD/AP/US, VECTOR 46, VECTOR 55, VECTOR 55/3X, VECTOR 70, VECTOR 70/3X, EDGE 45, EDGE 55, EDGE 55/H, EDGE 70, ENDURA 46, ENDURA 50, ENDURA 55, ENDURA PRO 46, ENDURA PRO 55, CAMO 55XL, RT 55/ST/CP , RT 55/ST/CP/AP, RT 55/SP/CP, RT 55/SP/CP/AP, RT 70/SP/CP, RT 70/SP/CP/AP, RT 55/SM /L&D, RT 55/SM/L&D/SC, RT 55/SM/L&D/3X, RT 55/SM/BG/3X, RT 70/SM/L&D/SC , RT 55/SE/L&D, RT 70/SE/L&D, RT 55/B/H, RT55/B/SC/L&D, RT55/B/L&D/3X, RT55/B/3X, RT65/B/SC, RT65/B/SC/L&D/3X, RT 70/B/H, RT 70/SC, RT50/S, RT55/S, MK55EM, RT 55EM, TRAXXIS 70, TRAXXIS 55, TRAXXIS 55/SCWARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Brochure (pdf)

    Read more

    $31.99 $27.99

  • Sale -$2.00 Flitz Instant Brass & Copper Tarnish Remover - 16. oz Spray [BC 01806]

    Flitz Flitz Instant Brass & Copper Tarnish Remover - 16. oz Spray [BC 01806]

    Instant Brass & Copper Tarnish RemoverNatural Organic salts formula Instantly Removes heavy tarnish without rubbing. Safer than traditional acid-based cleaners. Just spray & rinse. Use Indoors or Out.Instantly removes:Heavy tarnish, Rust & corrosion, Calcium deposits & stains, Heavy oxidation, Water spots & stainsSafe on:Glass, aluminum, painted surfaces, fiberglass, stucco, brick, porcelain, brass & copper. Works great on heavy tarnish, rust & corrosion, calcium deposits & stains, heavy oxidation, water spots & stains.Not for: Chrome or Patina finishes. WARNING: This product can expose you to chemicals including Methanol which is known to the State of California to cause reproductive harm, and 1, 4-Dioxane which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov. Specifications: Type: Metal Box Dimensions: 2"H x 4"W x 10"L WT: 1.2 lbs UPC: 065925018066

    Read more

    $19.95 $17.95

  • Sale -$6.01 Toadfish Non-Tipping Can Cooler 2.0 - Universal Design - Navy [5014]

    Toadfish Toadfish Non-Tipping Can Cooler 2.0 - Universal Design - Navy [5014]

    Non-Tipping Can Cooler 2.0 - Universal Design - NavyThe Toadfish Non-Tipping Can Cooler 2.0 has a one-size-fits-all design. Much like the regular Toadfish Non-Tipping Can Cooler, this is the first of its kind—an un-spillable beverage cooler. Innovative SmartGrip technology allows the can cooler to stick to any smooth surface. From a lack of cup holders on a rocking boat to wagging dog tails, this product will keep your drink upright, accident-free, and icy cold. To use, simply place the can cooler on any smooth surface, and it will keep the drink in place (securely up-right).Features: Universal design fits bottles and 12oz cans (normal and slim) Navy can cooler  Cup-holder compatible SmartGrip Technology - Patented SmartGrip technology makes it hard to tip but easy to lift Double-Wall Vacuum Insulation - Keeps your drinks cold until the last sip Stainless Steel - Made with high-grade stainless steel, making them puncture & rust-resistant Rubber Locking Gasket - Removable rubber gasket to securely lock in the can

    Read more

    $25.00 $18.99

  • Sale -$7.00 Meguiar's #45 Boat/RV Polish & Gloss Enhancer - 16oz [M4516]

    Meguiar's Meguiar's #45 Boat/RV Polish & Gloss Enhancer - 16oz [M4516]

    Boat/RV Polish & Gloss Enhancer16ozRestores brilliant gloss on fiberglass and painted marine or RV surfaces after cleaning. Restores valuable oils to feed and nourish the fiberglass or painted surfaces. Especially effective on dark colors. *Use polish only after the surface has been cleaned and restored to a "like new" or "average" finish.Benefits Effortless application and wipe-off in full sun Product can be safely applied with a Dual Action Polisher Product can be applied by hand High Speed Rotary Non-Scratch Creates a brilliant high-gloss surface VOC Compliant Specifications: Type: Waxes & Polishes Box Dimensions: 2"H x 4"W x 11"L WT: 1.2 lbs UPC: 070382145163

    Read more

    $18.99 $11.99

  • Sale -$2.00 Xanigo Marine Waterless Wash Fabric Refresher - 1qt [XMAP32]

    Xanigo Marine Xanigo Marine Waterless Wash Fabric Refresher - 1qt [XMAP32]

    Waterless Wash & Fabric Refresher - 1qtThe Xanigo Marine Waterless Wash is the perfect way to keep the boat clean between Xanigo Marine Mold & Mildew Preventer applications without the use of harsh chemicals or wasting water. No hose or running water is needed!Protect investments by protecting against mold and mildew on seats, life jackets, vinyl, canvas, ropes, carpets, and other areas with high moisture.Specifications:Bottle Size: 1 quartThe Complete Process to Treat and Prevent Mold & Mildew on Vinyl Boat SeatsSTEP 1: Remove Mold & Mildew with Xanigo Marine's Mold & Mildew Stain RemoverXanigo Marin’s Mold & Mildew Stain Remover is a very effective way to remove mold and mildew. Being a harsh chemical, it should only be used once to remove the mold, and then the preventer should be applied to prevent the mold from coming back. Liberally apply the Mold & Mildew Stain Remover to the seats. Let it sit for 60-90 seconds but do not let it dry. An additional solution may need to be applied— keep it wet. Agitate in a circular motion with a brush to remove the mold from the pores. Rinse thoroughly with clean water.STEP 2: Neutralize the RemoverAfter rinsing the remover off with fresh water, it's important to make sure any leftover remover is neutralized so it doesn't dry out vinyl or impact stitching. Spray the Waterless Wash onto the seats and wipe it in with a microfiber cloth to neutralize the chemicals in the remover.STEP 3: Prevent Mold & Mildew with Xanigo Marine's Mold & Mildew PreventerWith just one application, a boat will be protected against mold and mildew for up to 90 days. The preventer creates a covalent bond with the surface on which it is applied. Users can apply this to almost any marine surface, including vinyl seats, life jackets, canvas, ropes, compartments, live wells, bilges, patio furniture, and other areas of high moisture.Spray the Mold & Mildew Preventer onto a clean, dry surface and spread it evenly with a microfiber cloth. Remember to spread, not wipe off.STEP 4: Maintain Seats with Xanigo Marine's Waterless WashKeep the boat clean between mold prevention applications without the use of harsh chemicals or wasting water. Spray the Waterless Wash onto the seats, let it sit for 15-20 seconds, and wipe it off with a microfiber cloth. Remove sunscreen (a major food source for mold) and leave a refreshing smell without impacting the protective layer created by the mold & mildew preventer.Also, a great way to shine up a gel coat quickly! Specifications: Type: Washes Box Dimensions: 3"H x 3"W x 10"L WT: 2.3 lbs UPC: 860007772740 Quick Guide (pdf)

    Read more

    $34.99 $32.99

  • Sale -$8.00 Stay Afloat Marine Instant Leak Plug Sealant - 14oz [SA-0214]

    Stay Afloat Stay Afloat Marine Instant Leak Plug Sealant - 14oz [SA-0214]

    Instant Leak Plug & Sealant - 14ozStay Afloat is an instant-leak plug and sealant. It is a simple and versatile material intended to be used to stop or slow water leaks. Used alone, it requires no mixing, measuring, or curing. It is easily molded and applied by hand into holes, gaps, and cracks. Applied in sufficient quantity, it can stop or slow many types of leaks, and when combined with other material(s), such as wood or plastic, it can stop or slow larger leaks.Stay afloat has been used in many rescue operations, yet it takes common sense to know where, when, and how it can be used. (It is not a miracle product or gimmick.) In most cases, Stay Afloat is a temporary fix, and leaks should be permanently repaired as soon as possible.Features:Additional applications include sealing, lubricating, and water-proofingSpecifications:Size: 14oz Quick Guide (pdf)

    Read more

    $21.99 $13.99

  • Sale -$38.90 T-H Marine 6" Hole Shot Plate f/Z-Lock Jack Plate [JPZHSP-6]

    T-H Marine Supplies T-H Marine 6" Hole Shot Plate f/Z-Lock Jack Plate [JPZHSP-6]

    6" Hole Shot Plate for Z-Lock™ Jack PlateREVOLUTIONARY...SIMPLE...UNIQUE...EXCITING.These are but a few of the comments coming from users of T-H Marine's HOT SHOT™ hole shot plates. This simple but revolutionary plate easily attaches to the bottom of our jack plate to provide an amazing 18 to 20 percent better hole shot. That's 2 to 3 seconds faster out of the hole. Hot Shot™ does this by dramatically reducing water drag on take-off as well as serving as a center trim tab. An added advantage is the ability to stay on a plane and virtually eliminate porpoising at lower speeds.Models available for Z-LOCK™ manual plates.  Features: Provides Improved Hole Shot Reduces Water Drag at Take Off Reduces Porpoising WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

    Read more

    $96.89 $57.99

  • Sale -$44.00 Faria Chesapeake White SS 2" Depth Sounder w/Thru-Hull Transducer [13894]

    Faria Beede Instruments Faria Chesapeake White SS 2" Depth Sounder w/Thru-Hull Transducer [13894]

    Chesapeake White SS 2" Depth Sounder with Thru-Hull TransducerPerimeter-lighted black dial with stylish Blue and White graphics, polished stainless steel bezel, and domed glass lens.The Depth Sounders from Faria offer a 3-199 foot (1-61meters) depth capability, with an automatic gain control, backlighting for maximum night vision, keel offset, and deep and shallow water alarms. Depth can be read in meters, and feet. With its oversized back-lit display depth can be easily read in any condition. Audible and Visual alarms let the boater know when a shallow or deep water condition exists.  Depth Sounder includes a Faria SN2060 thru-hull mount transducer w/26' cable.2" - Hole Size: 2.0625" (53mm)Specifications: Imperial and Metric Values Domed Glass Anti-fog, Scratch Resistant Lens Programmable Keel Offest  Stainless Steel Bezel 199 Foot (61m) Depth Capability Audible and Visual alarm for Shallow/Deep Water Conditions Factory P/N DS0110*Sold as an Individual**Gauge Cover not IncludedThis product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns. Specifications: Box Set: No Gauge Type: Depth Sounder Voltage - Input Range (Volts): 12/24 V Series: Chesapeake White Gauge Size: 2" Box Dimensions: 8"H x 8"W x 9"L WT: 2.1 lbs UPC: 759266138940 Owner's Manual (pdf)

    Read more

    $259.99 $215.99

  • Sale -$17.96 Swobbit Quick Dry Water Blade - 18" [SW21314]

    Swobbit Swobbit Quick Dry Water Blade - 18" [SW21314]

    Quick Dry Water Blade - 18"Swobbit award winning water blades are made of high quality, medical grade silicone.  Perfect for a drying all types of surface types and surface sizes. No need for messy towels or chamois. Whether marine, auto, RV or aviation, Swobbit water blades make protecting your investment, a simple one. Features: T-Bar edge whisks away water in one pass Dries virtually any surface in 1/3 the time of messy towels, chamois or squeegees  15 times less friction than towels Safe for all finishes including paint, fiberglass, windows and enclosures Can be used with the Quick Dry Uni-Snap adapter (SW21215) to dry hard to reach areas *Sold as an Individual  Specifications: Type: Tools & Accessories Box Dimensions: 2"H x 3"W x 18"L WT: 0.6 lbs UPC: 633590213149 Brochure (pdf)

    Read more

    $54.95 $36.99

  • Sale -$15.00 Corrosion Block 12oz Aerosol Can - Non-Hazmat, Non-Flammable Non-Toxic [20012]

    Corrosion Block Corrosion Block 12oz Aerosol Can - Non-Hazmat, Non-Flammable Non-Toxic [20012]

    12oz Aerosol Can - Non-Hazmat, Non-Flammable & Non-ToxicCorrosion Block is a clean fluid that actively protects metal using advanced polar bonding chemistry.  Synthetic additives in Corrosion Block completely penetrate corrosion cells…replacing the salt water which is then allowed to evaporate.  Corrosion Block’s hydrophobic film remains to further protect the metal acting like an “OFF SWITCH” for corrosion. Unlike waxy products Corrosion Block then leaves a clean clear moisture proof/hydrophobic film to prevent new corrosion formation. deeply penetrating into joints, connectors and around fasteners. Features: Formulated to KILL CORROSION ON CONTACT from completely submerged, to equipment affected by high moisture content in the air Corrosion Block is a clean fluid that actively protects metal and electronics using advanced polar bonding chemistry Synthetic additives in Corrosion Block completely penetrate corrosion cells...replacing the salt water which is allowed to evaporate A hydrophobic film remains to further protect the metal acting like an "OFF SWITCH" for corrosion Corrosion Block is safe; it is non-toxic and non-flammable, also the propellant used in our aerosol products is non-flammable Used worldwide to protect electrical and mechanical equipment in "Safety First" situations such  as Mining, Power Generating Stations, Fuel Depots, Gas and Petroleum refineries and more Protects: Switches Pressure Gauges Motor Operated Valves Terminal Strips Circuit Breakers Locks  Electronics Battery Terminals Running Lights Fuel Tanks Fuse Panels Connectors Alternator Leads Reefer Unit Wheels & Hubs Engines GPS Systems  Specifications: Type: Corrosion Protection Box Dimensions: 2"H x 2"W x 10"L WT: 0.95 lbs UPC: 770153200120

    Read more

    $29.99 $14.99

  • Sale -$10.00 VDO Reed Switch Fuel Sender - 150 MM [226-615]

    VDO VDO Reed Switch Fuel Sender - 150 MM [226-615]

    Reed Switch Fuel Sender - 150 MMMost aftermarket fuel senders use a rotating float arm and resistance cards to measure the amount of fuel in a tank which can lead to erratic pointer movements.  This revolutionary design comes with many benefits!  This is ideal for applications where a conventional swing arm will not fit due to clearance issues.  The tubular design acts as a dampener to prevent the gauge pointer from moving due to fuel slosh.  The floatless fuel sender has no side to side motion, which means it has no moving parts to wear out.  It is top mounted and utilizes the aftermarket standard SAE 5 hole mounting flange and comes complete with neoprene gasket and mounting hardware. Features: Stainless steel construction Ethanol resistant Viton gasket 240-33 Ohm range Fits tanks with a depth of 6" (150mm)  Insulated 1/4"" spade connectors Standard 5 hole mounting flange Works with most standard marine fuel gauges Ground - Floating Connection - Insulated .25" Spade *Sold as an IndividualWARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Color: Silver Box Dimensions: 3"H x 3"W x 10"L WT: 0.6 lbs UPC: 754059064352

    Read more

    $49.99 $39.99

  • Sale -$6.10 Sika Aktivator-205 Clear 250ml Bottle [108616]

    Sika Sika Aktivator-205 Clear 250ml Bottle [108616]

    Aktivator-205 Clear 250ml BottleSika® Aktivator-205 is a solvent-based colorless clear adhesion promoter, which reacts with moisture and deposits active groups on the substrate. These groups act as a link between substrates and primers or sealants/adhesives. Sika® Aktivator-205 is designed for the treatment of bond faces prior to the application of Sikaflex® and Sikasil® adhesives and sealants.   Features: Enhanced adhesion on various substrates Short flash-off time Easy to use Transparent Areas of Application:Sika® Aktivator-205 is used to improve adhesion on non-porous substrates such as metals, plastics, ceramic screen prints, and painted surfaces. Seek manufacturer’s advice and perform tests on original substrates before using Sika® Aktivator-205 on materials prone to stress cracking. This product is suitable for experienced professional users only. Tests with actual substrates and conditions have to be performed to ensure adhesion and material compatibility.

    Read more

    $33.09 $26.99

  • Sale -$3.00 Sika Sikaflex 295 UV - White - 10oz Tube w/Nozzle [769]

    Sika Sika Sikaflex 295 UV - White - 10oz Tube w/Nozzle [769]

    Sikaflex® 295 UV - White - 10oz Tube with NozzleExterior sealant and direct glazing adhesive for organic glass in Marine applications. Sikaflex®-295 UV is a 1-component polyurethane adhesive of paste-like consistency that cures on exposure to atmospheric moisture. It is suitable for interior and exterior sealing applications and to bond organic glass in the Marine business. Sikaflex®-295 UV meets the requirements set out by the International Maritime Organization (IMO).  Features: Excellent application properties Resistant to aging and weathering Suitable for organic glasses Areas of ApplicationSikaflex®-295 UV has been specially developed for the marine industry, where it is used to bond and seal plastic glazing materials in boats and ships. Because of its excellent weatherability this product can also be used to seal joints in exposed areas. Suitable substrates are aluminum (bright or anodized), GRP (polyester resin), stainless steel, timber, 2-component coatings, and plastic glazing materials (PC, PMMA). Seek manufacturer’s advice and perform tests on original substrates before using Sikaflex®-295 UV on materials prone to stress cracking. This product is suitable for experienced professional users only. Tests with actual substrates and conditions have to be performed to ensure adhesion and material compatibility.Product Benefits: Excellent application properties Resistant to aging and weathering Suitable for organic glasses Approved for the OEM market Wheelmark approved Surface Preparation:Surfaces must be clean, dry, and free from grease, oil, dust, and contaminants. Surface treatment depends on the specific nature of the substrates and is crucial for a long-lasting bond. Suggestions for surface preparation may be found on the current edition of the appropriate Sika® Pre-treatment Chart. Consider that these suggestions are based on experience and have in any case to be verified by tests on original substrates. Application:Sikaflex®-295 UV can be processed between 10 °C and 35 °C (climate and product) but changes in reactivity and application properties have to be considered. The optimum temperature for substrate and sealant is between 15 °C and 25 °C.Consider that the viscosity will increase at low temperatures. For easy application, condition the adhesive at ambient temperature prior to use. To ensure a uniform thickness of the bonding it is recommended to apply the adhesive in form of a triangular bead.Tooling & FinishingTooling and finishing must be carried out within the skin time of the product. It is recommended to use Sika® Tooling Agent N. Other finishing agents must be tested for suitability and compatibility prior to the use. RemovalUncured Sikaflex®-295 UV can be removed from tools and equipment with Sika® Remover-208 or another suitable solvent. Once cured, the material can only be removed mechanically. Hands and exposed skin have to be washed immediately using Sika® Cleaner-350H cleaning towels or a suitable industrial hand cleaner and water. Do not use solvents on the skin.OverpaintingSikaflex®-295 UV can be painted prior to and after the formation of the skin. If the painting process takes place after the sealant has built a skin, adhesion could be improved by treating the joint surface with Sika® Aktivator-100 or Sika® Aktivator-205 prior to the painting process. If the paint requires a baking process (> 80 °C), the best performance is achieved by allowing the sealant to fully cure first. All paints have to be tested by carrying preliminary trials under manufacturing conditions. The elasticity of paints is usually lower than that of sealants. This could lead to cracking of the paint in the joint area.

    Read more

    $24.99 $21.99

  • Sale -$3.00 Sika Sikaflex 295 UV - Black - 10oz Tube w/Nozzle [778]

    Sika Sika Sikaflex 295 UV - Black - 10oz Tube w/Nozzle [778]

    Sikaflex® 295 UV - Black - 10oz Tube with NozzleExterior sealant and direct glazing adhesive for organic glass in Marine applications. Sikaflex®-295 UV is a 1-component polyurethane adhesive of paste-like consistency that cures on exposure to atmospheric moisture. It is suitable for interior and exterior sealing applications and to bond organic glass in the Marine business. Sikaflex®-295 UV meets the requirements set out by the International Maritime Organization (IMO).  Features: Excellent application properties Resistant to aging and weathering Suitable for organic glasses Areas of ApplicationSikaflex®-295 UV has been specially developed for the marine industry, where it is used to bond and seal plastic glazing materials in boats and ships. Because of its excellent weatherability this product can also be used to seal joints in exposed areas. Suitable substrates are aluminum (bright or anodized), GRP (polyester resin), stainless steel, timber, 2-component coatings, and plastic glazing materials (PC, PMMA). Seek manufacturer’s advice and perform tests on original substrates before using Sikaflex®-295 UV on materials prone to stress cracking. This product is suitable for experienced professional users only. Tests with actual substrates and conditions have to be performed to ensure adhesion and material compatibility.Product Benefits: Excellent application properties Resistant to aging and weathering Suitable for organic glasses Approved for the OEM market Wheelmark approved Surface Preparation:Surfaces must be clean, dry, and free from grease, oil, dust, and contaminants. Surface treatment depends on the specific nature of the substrates and is crucial for a long-lasting bond. Suggestions for surface preparation may be found on the current edition of the appropriate Sika® Pre-treatment Chart. Consider that these suggestions are based on experience and have in any case to be verified by tests on original substrates. Application:Sikaflex®-295 UV can be processed between 10 °C and 35 °C (climate and product) but changes in reactivity and application properties have to be considered. The optimum temperature for substrate and sealant is between 15 °C and 25 °C.Consider that the viscosity will increase at low temperatures. For easy application, condition the adhesive at ambient temperature prior to use. To ensure a uniform thickness of the bonding it is recommended to apply the adhesive in form of a triangular bead.Tooling & FinishingTooling and finishing must be carried out within the skin time of the product. It is recommended to use Sika® Tooling Agent N. Other finishing agents must be tested for suitability and compatibility prior to the use. RemovalUncured Sikaflex®-295 UV can be removed from tools and equipment with Sika® Remover-208 or another suitable solvent. Once cured, the material can only be removed mechanically. Hands and exposed skin have to be washed immediately using Sika® Cleaner-350H cleaning towels or a suitable industrial hand cleaner and water. Do not use solvents on the skin.OverpaintingSikaflex®-295 UV can be painted prior to and after the formation of the skin. If the painting process takes place after the sealant has built a skin, adhesion could be improved by treating the joint surface with Sika® Aktivator-100 or Sika® Aktivator-205 prior to the painting process. If the paint requires a baking process (> 80 °C), the best performance is achieved by allowing the sealant to fully cure first. All paints have to be tested by carrying preliminary trials under manufacturing conditions. The elasticity of paints is usually lower than that of sealants. This could lead to cracking of the paint in the joint area.

    Read more

    $24.99 $21.99

  • Sale -$25.56 Lenco Single Rocker Switch f/Airboat [15095-001]

    Lenco Marine Lenco Single Rocker Switch f/Airboat [15095-001]

    Single Rocker Switch for AirboatSingle Rocker Switch with deutsch connector and two 30" non-terminated power leads. Recommended for use with 15112-101 Airboat Trim Tab Kit Features: Switch specifically used for Airboat Single Rocker Switch (2) 30" non-terminated power leads WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

    Read more

    $76.55 $50.99

  • Sale -$10.00 Minn Kota Micro Remote-Bluetooth [1866561] Minn Kota Micro Remote-Bluetooth [1866561]

    Minn Kota Minn Kota Micro Remote-Bluetooth [1866561]

    Micro Remote-BluetoothMinn Kota's advanced GPS navigation system gives you full command of your trolling motor. But when you want simplified, compact control, grab the new waterproof Bluetooth Micro Remote accessory for quick command of Spot-Lock, speed, steering, and AutoPilot. Navigation systems can learn multiple remotes for increased flexibility.Features: Minn Kota trolling motors can learn multiple remotes, so you can use your standard remote and Micro Remote together Compatible only with Bluetooth-enabled Minn Kota navigation systems manufactured after 2017 Waterproof The remote is powered by one replaceable CR2450 coin-cell lithium battery. Includes neck lanyard

    Read more

    $109.99 $99.99

  • Sale -$9.00 Faria Chesapeake White SS 2" Fuel Level Gauge (E-1/2-F) [13801]

    Faria Beede Instruments Faria Chesapeake White SS 2" Fuel Level Gauge (E-1/2-F) [13801]

    Chesapeake White SS 2" Fuel Level Gauge (E-1/2-F)Perimeter-lighted White dial with stylish Blue and White graphics, polished stainless steel bezel, contoured White pointer and domed glass lens.Fuel Level gauge operates by sending a low amperage current through the gauges meter to ground via a sending unit with variable resistance. The resistance of the sending units increase or decrease with the changes in pressure, temperature, etc...As the sender's resistance varies, the amount of current allowed to flow through it to ground changes and the meter deflects, showing the level of fuel.2" - Hole Size: 2.0625" (53mm)Specifications: Anti-scratch glass lens Perimeter lighted back light 12 VDC negative ground Can be adapted for 24 VDC systems Factory P/N GP9373*Sold as an Individual**Gauge Cover not IncludedThis product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns. Specifications: Gauge Type: Fuel Level Series: Chesapeake White Gauge Size: 2" Box Set: No Voltage - Input Range (Volts): 12/24 V Box Dimensions: 4"H x 4"W x 5"L WT: 0.3 lbs UPC: 759266138018 Quick Guide (pdf)

    Read more

    $44.99 $35.99

  • Sale -$8.00 Whitecap Teak Toilet Tissue Rack [62322] Whitecap Teak Toilet Tissue Rack [62322]

    Whitecap Whitecap Teak Toilet Tissue Rack [62322]

    Toilet Tissue Rack Spring-loaded bar 1-7/8"H x 5-1/2"W x 3-3/4"D

    Read more

    $24.99 $16.99

  • Sale -$0.19 Shurhold Replacement 5" Dual Action Polisher Backing Plate [3130]

    Shurhold Shurhold Replacement 5" Dual Action Polisher Backing Plate [3130]

    Replacement 5" Dual Action Polisher Backing PlateFeatures: Designed specifically to work with Shurhold's Award winning Dual Action Polisher. 5" (125mm) polyurethane backing plate with 5/16" (24) treaded post Quick release hook and loop system, works with most 5.5" - 6.5" (140 -165mm) Velcro style pads Specifications: Type: Buffers & pads Box Dimensions: 1"H x 5"W x 5"L WT: 0.3 lbs

    Read more

    $15.17 $14.98

  • Sale -$9.00 STA-BIL Fuel Stabilizer - 1 Gallon [22213]

    STA-BIL STA-BIL Fuel Stabilizer - 1 Gallon [22213]

    Fuel Stabilizer - 1 GallonAMERICA’S #1 FUEL STABILIZER TREATMENTSTA-BIL Storage Fuel Stabilizer keeps fuel fresh for quick easy starts after storage. It removes water to prevent corrosion and cleanses carburetors and fuel injectors. This product also protects the engine from gum, varnish, rust, and corrosion and prolongs the life of any engine. Eliminate the need to drain the fuel of your 2 or 4 cycle engine by treating the fuel with STA-BIL before storing.USAGE DIRECTIONS:Use STA-BIL Fuel Stabilizer in any gasoline-powered vehicle or equipment you plan to store for 30-days or longekeeps the fuel fresh for up to 24 months during storage, eliminating the need to drain your tank. Works effectively in all gasoline blends, including Ethanol-blended fuel, up to E-85. 1-ounce (30-milliliter) treats up to 2½ gallons (9.5-liters) of fuel. Use STA-BIL only with fresh fuel, and keep the gas can or tank 95% full to avoid condensation build up in the tank during storage. Run Engine for 5 minutes after adding product to treat entire fuel system. Product does not contain alcohol. Perfect for collector cars, generators, lawn mowers, snow blowers, etc.PERFECT FOR STORING: LAWNMOWERS: Fuel can deteriorate in as little as 60 days, causing gum and varnish to build up in your lawnmower engine. That means difficulty starting the engine, poor performance and reduced engine life. The simplest, easiest fix is using a fuel stabilizer to prevent fuel deterioration during storage. BOATS: Drain the lower unit of old gear oil and replace with a fresh supply. When changing the gear oil, be sure to check for moisture. If water comes out first, or if you see milky or lumpy oil, this is an indication your boat is experiencing moisture contamination and will need new seals before next season. AUTOMOBILES: Fill the tank 95% full with new fuel and add STA-BIL Storage to keep it fresh for up to 24 months. MOTORCYCLES: When putting your bike away for the season, it’s important to find winter storage that is dry and protected from environmental elements. Avoid storing it near windows to prevent the paint from fading with constant contact with light. Features: America’s #1 Fuel Stabilizer Treatment Keeps fuel fresh for long term storage – up to 24 months Eliminates the need to drain fuel prior to storage Ensures quick easy starts after storage by preventing gum and varnish build up* Effective in all gasoline, including Ethanol and Non-Ethanol For all gasoline engines, including 2-Cycle. Use in your vehicles, motorcycles, small engines, generators, boats Made in the U.S.A. WARNING: This product can expose you to chemicals including benzene which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Type: Engine & Fuel Box Dimensions: 5"H x 7"W x 11"L WT: 7.15 lbs UPC: 073905222136

    Read more

    $56.99 $47.99

  • Sale -$5.00 BoatLIFE Teak Brite Advanced Formula Teak Oil - 32oz [1188]

    BoatLIFE BoatLIFE Teak Brite Advanced Formula Teak Oil - 32oz [1188]

    Teak Brite® Advanced Formula Teak Oil - 32ozMost advanced teak oil and sealer available. Will deliver long lasting protection even in tropical climates. Penetrates deep into wood (dry wood only) to feed and protect finish. Compatible with Life-Calk® seam compounds. (Hint: for a fantastic finish, allow teak to dry for at least 24 hours minimum before applying oil). Specifications: Type: Teak Box Dimensions: 3"H x 5"W x 7"L WT: 2.1 lbs UPC: 020537011881

    Read more

    $38.99 $33.99

  • Sale -$1.05 Octopus Hydraulic Steering Fluid - Quart [OCTOIL1USQ]

    Octopus Autopilot Drives Octopus Hydraulic Steering Fluid - Quart [OCTOIL1USQ]

    Hydraulic Steering Fluid - QuartFeatures: Applications: All Hydraulic Steering Systems Type: ISO 15 Low Temp Mineral Hydraulic Fluid Select Container Size: Quart

    Read more

    $19.04 $17.99

  • Sale -$1.97 Shurhold Bucket Seat/Lid - Black [2403]

    Shurhold Shurhold Bucket Seat/Lid - Black [2403]

    Bucket Seat/LidFeatures: Contoured, durable and soft lid for seating Protects bucket contents from weather Specifications: Type: Tools & Accessories Box Dimensions: 2"H x 12"W x 12"L WT: 0.9 lbs UPC: 703485121092

    Read more

    $14.95 $12.98

  • Sale -$14.01 Toadfish Stainless Steel Wine Chiller - Rose Gold [1110]

    Toadfish Toadfish Stainless Steel Wine Chiller - Rose Gold [1110]

    Stainless Steel Wine Chiller - Rose GoldThe Toadfish® Wine Chiller is the ultimate wine accessory. Keep your favorite wine at the perfect temperature longer. Double-walled, stainless steel construction keeps your wine, champagne, sparkling water, or other like-size beverage chilled for hours. Take your iceless chilled wine anywhere with this revolutionary, easy-to-carry, lightweight, and portable design.Features: Color: Rose gold Condensation-free and does not require ice The adjustable top fits more bottles, better Adjustable Top - fits most standard wine, Champagne, Sparkling Water Bottles, etc. Flexi-Lock Design - holds the bottle securely while pouring Double-Wall Vacuum Insulation - keeps desired liquid chilled for hours! Stainless Steel - Made with high-grade stainless steel for a condensation-free grip How to UseSimply unscrew the top, insert your chilled bottle, screw the top back on, and enjoy! The expandable locking lid holds your bottle securely while pouring so you don't have to worry about taking the bottle in and out until it's empty.*DO NOT place wine chiller in the freezer

    Read more

    $50.00 $35.99

  • Sale -$5.00 Meguiar's #47 Hard Water Spot Remover - 16oz [M4716]

    Meguiar's Meguiar's #47 Hard Water Spot Remover - 16oz [M4716]

    Hard Water Spot Remover16ozThick low drip formula remains on vertical surfaces for easy cleaning. New technology chemically embraces and lifts mineral deposits and protects surface from future water spots. Easy to apply and easy to wipe off.Benefits Cleans surface dirt and grime Effortless application and wipe-off in full sun Product can be applied by hand Brings back to like-new condition VOC Compliant Specifications: Type: Hard Water Box Dimensions: 2"H x 4"W x 11"L WT: 1.2 lbs UPC: 070382147167

    Read more

    $17.99 $12.99

  • Sale -$6.01 Toadfish Non-Tipping Can Cooler 2.0 - Universal Design - Teal [5004]

    Toadfish Toadfish Non-Tipping Can Cooler 2.0 - Universal Design - Teal [5004]

    Non-Tipping Can Cooler 2.0 - Universal Design - TealThe Toadfish Non-Tipping Can Cooler 2.0 has a one-size-fits-all design. Much like the regular Toadfish Non-Tipping Can Cooler, this is the first of its kind—an un-spillable beverage cooler. Innovative SmartGrip technology allows the can cooler to stick to any smooth surface. From a lack of cup holders on a rocking boat to wagging dog tails, this product will keep your drink upright, accident-free, and icy cold. To use, simply place the can cooler on any smooth surface, and it will keep the drink in place (securely up-right).Features: Universal design fits bottles and 12oz cans (normal and slim) Teal can cooler Cup-holder compatible SmartGrip Technology - Patented SmartGrip technology makes it hard to tip but easy to lift Double-Wall Vacuum Insulation - Keeps your drinks cold until the last sip Stainless Steel - Made with high-grade stainless steel, making them puncture & rust-resistant Rubber Locking Gasket - Removable rubber gasket to securely lock in the can

    Read more

    $25.00 $18.99

  • Sale -$5.56 Sika Sikaflex 221 Multi-Purpose Polyurethane Sealant/Adhesive - 10.3oz(300ml) Cartridge - Black [90893]

    Sika Sika Sikaflex 221 Multi-Purpose Polyurethane Sealant/Adhesive - 10.3oz(300ml) Cartridge - Black [90893]

    Sikaflex® 221 Multi-Purpose Polyurethane Sealant/Adhesive - 10.3oz(300ml) Cartridge - BlackSikaflex®-221 is a high-quality multi-purpose non-sag 1-c polyurethane sealant/adhesive that cures on exposure to atmospheric humidity to form a durable elastomer. Meets approvals ASTM C920 types Sikaflex®-221 is tested and classified in accordance with ANSI/UL 723 “Test for Surface Burning Characteristics of Building Materials”.Uses:Sikaflex®-221 bonds well to a wide variety of substrates and is suitable for making permanent elastic seals of high adhesive strength. Suitable substrate materials are wood, metals, metal primers and paint coatings (2-c systems), ceramic materials and plastics.Characteristics & Advantages: Highly elastic and durable Resistant to aging and weathering exposure Non-corrosive Can be sanded and overpainted NSF registered, Proprietary Substances and Nonfood Compounds (black, gray, and white) UL listed for potable water (black, gray, and white) WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Quick Guide (pdf)

    Read more

    $15.55 $9.99

  • Sale -$6.00 Super Stainless 16oz Stainless Steel Cleaner [SS16]

    Super Stainless Super Stainless 16oz Stainless Steel Cleaner [SS16]

    16oz Stainless Steel CleanerThis is a phosphoric acid-based stainless steel cleaner. Features: It removes rust staining and surface corrosion from polished marine-grade stainless steel  Shelf Life at 23 degrees Celsius is 24 months  Specifications: pH Value: 1.0 Size: 16oz bottle Contents: Contains non-ionic surfactants < 5%  Recommended Applications: A brush is recommended, but cotton, a rag, or a sponge may be used Recommended UseUsed for cleaning rust staining and surface corrosion from polished marine-grade stainless steel.Surface PreparationApply the product to the area to be treated. Allow it to work for up to 30 minutes. Rinse well with fresh water and a sponge.Pre-treatmentClean with detergent.StorageThis product must be stored in accordance with national regulations. Keep the containers in a dry, cool, and well-ventilated space away from sources of heat and ignition. Containers must be kept tightly closed. Handle with care. Quick Guide (pdf)

    Read more

    $24.99 $18.99

  • Sale -$28.00 Attwood Portable Fuel Tank - 6 Gallon w/Gauge [8806LPG2]

    Attwood Marine Attwood Portable Fuel Tank - 6 Gallon w/Gauge [8806LPG2]

    Portable Fuel Tank - 6 Gallon with GaugeAttwood has engineered the industry’s only comprehensive EPA-certified fuel tank-to-engine solution. Rugged materials and innovative design stand up to harsh marine conditions. 6-gallon tank adapts to virtually any outboard engine. Includes gauge.Features: 6 Gallon fuel capacity Compatible with 1/4" NPT fuel fittings Additional oil and ullage/vapor capacity EPA Cap with automatic, high-flow vacuum valve Cap with built-in vacuum valve means no need for manual venting High-contrast & easy to read gauge Automotive-grade, multi-layer construction withstands the pressure build-up associated with closed fuel systems Meets EPA and CARB (California Air Resources Board) regulations Complies with all ABYC/NMMA requirements for portable marine fuel tanks Dimensions: Length: (inch) 19.82" Width: (inch) 13.50" Height: (inch) 9.16" *Fuel line is not includedWARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Quick Guide (pdf)

    Read more

    $92.99 $64.99

  • Sale -$42.09 Marinco 303SSEL-B 30A Power Inlet - Stainless Steel - 125V [303SSEL-B]

    Marinco Marinco 303SSEL-B 30A Power Inlet - Stainless Steel - 125V [303SSEL-B]

    30A 125V Power Inlet303SSEL-BProduct Features Solid cast 316 stainless steel Locking waterproof cap Easy Lock System Soft Touch cap stays open in the upright position 8-way right angle rear safety enclosure WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Type: Inlets Box Dimensions: 4"H x 6"W x 9"L WT: 1.25 lbs UPC: 093344300172 Quick Guide (pdf)Owner's Manual (pdf)Brochure (pdf)

    Read more

    $123.08 $80.99

  • Sale -$7.00 Attwood Portable Fuel Tank Cap w/Tether - EPA Certified [88TC06-7]

    Attwood Marine Attwood Portable Fuel Tank Cap w/Tether - EPA Certified [88TC06-7]

    Portable Fuel Tank Cap with Tether - EPA CertifiedHigh-flow valve exceeds OEM engine fuel flow requirements. Be sure your fuel system is safe; the ratchet feature ensures a proper seal while the tether prevents cap loss. Very versatile; designed for 0 to 350 horsepower engines.Features: Standard 2 ¼ inch neck for convenience Includes high-flow automatic vacuum valve Tether Included Compatible with 8803LP/8806LP/8812LP/8812LLP Tanks Easy-to-grip cap features ratcheting noise so you know it’s properly sealed Quick Guide (pdf)

    Read more

    $27.99 $20.99

  • Sale -$4.96 Faria 2" Gauge Weather Cover - White [F91401]

    Faria Beede Instruments Faria 2" Gauge Weather Cover - White [F91401]

    2" Gauge Weather Cover - WhiteProtect your gauges from fading, scratches and the sun when not in use.  This protective cover fits snugly over the gauge to ensure your gauge looks as good as when you got it.Compatible with all Faria 2" Gauges. Available in 2", 4" or 5" size and in Black or White.*Sold as an IndividualThis product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns. Specifications: Diameter (mm): 51 Diameter (Inches): 2 Color: White Box Dimensions: 1"H x 2"W x 2"L WT: 0.1 lbs UPC: 759266914018 Quick Guide (pdf)

    Read more

    $9.95 $4.99

  • Sale -$8.00 Minn Kota MKA-50 Bow-Mount Stabilizer Kit f/Fortrex [1862050] Minn Kota MKA-50 Bow-Mount Stabilizer Kit f/Fortrex [1862050]

    Minn Kota Minn Kota MKA-50 Bow-Mount Stabilizer Kit f/Fortrex [1862050]

    MKA-50 Bow-Mount Stabilizer Kit for FortrexFeatures: Reduces motor bouncing when in stowed position Attaches to the left or right side of bowguard Pivots into vertical position and rests on the boat deck when motor is stowed Rotates in the horizontal position with bowguard when the motor is deployed Includes rubber bumper to protect deck finish Stainless steel hardware tested for saltwater use Fits any Fortrex or Riptide SF bow-mount trolling motor WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

    Read more

    $54.99 $46.99

  • Sale -$261.01 Turning Point Express Mach4 - Right Hand - Stainless Steel Propeller - EX-1421-4 - 4-Blade - 14" x 21 Pitch [31502131]

    Turning Point Propellers Turning Point Express Mach4 - Right Hand - Stainless Steel Propeller - EX-1421-4 - 4-Blade - 14" x 21 Pitch [31502131]

    Express® Mach4™ - Right Hand - Stainless Steel Propeller - EX-1421-4  - 4-Blade - 14" x 21 PitchThe Prop that put the "four" in Perfourmance! Turning Point's Four Blade revolutionized the propeller market when it was introduced. No one had ever produced a propeller with two different blade shapes (they call it Dual Geometry) for 90-300+hp applications. This prop is uniquely engineered with two blade geometries: (diagram label 2)two blades utilize the Hustler high performance variable rake and aggressive pitch design for incredible hole shot and cornering, and (diagram label 1) two blades utilize an offshore style design for high speed and maximum stern lift.These props re-wrote the rules, proving that you can run a four blade that has unprecedented hole shot, handling, and rough water stability without the top-end speed loss you experience with other manufacturers’ propellers.Now manufactured in our Industry leading TP17 stainless, the Express Mach4 series is perfect for any application that demands enhanced acceleration, cornering, and load carrying capabilities. This prop series is ideally suited for watersports, sterndrive boats, tri-toons, bay boats, and any vessel that can use stern lift. It is our best upgrade of older stainless designs from the 70’s, 80’s, 90’s, and ’00’s, and will outrun most newer props, including five blade ski props.Proprietary Stainless Steel, TP17™Formulated to meet the exacting requirements of the New Express Mach3 and Mach4 designs. 20% higher chromium content than the competition - more shine, better corrosion resistance. Almost 250% Stronger and 5X more durable than run-of-the-mill stainless steel. This new material allows Turning Point's Engineers and Designers the freedom to produce radical new designs that will help you wring the most performance out of your boat.Large Free Flowing Exhaust PortsTurning Point's Propeller Housings have massive Exhaust flow pathways. Their Propellers have 40% more exhaust flow Area versus competitive product. More exhaust flow and less backpressure can generate more horsepower. Like headers for your boat.Turning Point manufactures Express propellers to fit 9.9(bigfoot)-300+hp Evinrude®, Force®, Honda®, Johnson®, Mariner®, Mercruiser®, Mercury®, Nissan®, OMC®, Parsun®, Suzuki®, Tohatsu®, Volvo® Penta®, and Yamaha® Outboards and Sterndrives. Choose one of our Lifetime Warranty MasterGuard Installation Kits to fit your engine, then choose the propeller that matches your boating requirements. There are 3 and 4 blade, left and right rotation prop models with a variety of diameter and pitch options available for almost all boat types. Turning Point's Props Run Faster, Pull Harder, and Handle Better.Note: A Hub Kit is required for installation of this propeller. See the Turning Point Selection Chart or the Prop Wizard™ for hub kit selection.WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Pitch: 21 Material: Stainless Steel Diameter (Inches): 14" Rotation: Right Box Dimensions: 8"H x 16"W x 16"L WT: 16.85 lbs UPC: 652480200892 Quick Guide (pdf)Brochure (pdf)

    Read more

    $646.00 $384.99

  • Sale -$7.00 303 Marine Fabric Guard - 32oz [30604]

    303 303 Marine Fabric Guard - 32oz [30604]

    Marine Fabric Guard - 32oz303 Fabric Guard is the only product recommended by fabric manufacturers to restore lost water repellency to fabrics.  Resist water, even when you’re on the water.  303 Fabric Guard creates a powerful shield to greatly increase repellency and protect against oil and water- based stains. Spray it on outdoor leather seats, boat covers, awnings, Dacron sails and more.  When applied to clean and dry fabrics, 303 Fabric Guard restores lost water and stain repellency to straight-from-the-factory levels. Keep all your favorite fabrics crisp and clean for years to come.Features: Fabric protector spray that strengthens and restores lost water repellency for marine fabrics Safe for synthetic and natural fibers in marine environments Protects against both water-based and oil-based stains Does not alter fabric color, feel, flammability or breathability Recommended by leading outdoor fabric manufacturer Made in the U.S.A. *Sold as an Individual WARNING: This product can expose you to chemicals including Ethylbenzene which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov. Specifications: Type: Fabric & upholstery Box Dimensions: 3"H x 5"W x 12"L WT: 1.8 lbs UPC: 082043006508

    Read more

    $36.99 $29.99

  • Sale -$51.00 Marinco Dockside 30A to 15A Adapter with GFI [199128]

    Marinco Marinco Dockside 30A to 15A Adapter with GFI [199128]

    Dockside 30A to 15A Adapter with GFI Provides safer hook-up to 30A dockside power Provides protection against harmful electric shock Reduces the possibility of fire Offers protection for up to 3 attached tools Corrosion resistant and rain-proof rated for outdoor use GFI trip level of 4-6 mA WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Type: Pigtail Adapter Box Dimensions: 4"H x 8"W x 15"L WT: 2.1 lbs UPC: 093344312311

    Read more

    $149.99 $98.99

  • Sale -$2.02 STA-BIL Pump Protector - 4oz [22007]

    STA-BIL STA-BIL Pump Protector - 4oz [22007]

    Pump Protector - 4ozEver get your pressure washer out in the spring, fire it up, and you see water leaking from the bottom of the pump with no water pressure? This is due to seals going bad because of no lubrication, or in cold climates, water in the pump during the winter freezes and causes the cast pump to crack. STA-BIL Pressure Washer Pump Protector is quick and easy to use year-round to keep everything working properly inside your pressure washer. This product is great for protecting pressure washer pumps during storage as well as keeping pistons and seals fresh during the season for easy trouble-free startups. It is simple to use and takes seconds to protect your investment. The next-generation anti-freeze and lubricant will protect your pressure washer pumps 24/7. Screw the pump protector onto the water hose inlet of the pressure washer, with the pressure washer wand disconnected. Push down on the STA-BIL Pressure Washer Pump Protector trigger and hold until you see foam come out the side the wand connects onto. Your pressure washer is now lubricated and any standing water has been pushed out.Features: Protects Pressure Washer Pumps During Storage Protects Pistons and Seals From Damage Can Safely Be Drained Next Generation Anti-Freeze and Lubricant Formula Coats and Protects Components Of Pressure Washer To Prevent Freezing Helps Prevent Harmful Buildup Of Hard Water Mineral Deposits

    Read more

    $8.99 $6.97

  • Sale -$4.20 303 Marine Clear Vinyl Protective Cleaner - 32oz [30215]

    303 303 Marine Clear Vinyl Protective Cleaner - 32oz [30215]

    Marine Clear Vinyl Protective Cleaner - 32oz303 Clear Vinyl Protective Cleaner offers superior protection against the harmful effects of UV rays.  This product is all you need to safely clean and protect against yellowing and cracking of vinyl, clear vinyl, Strataglass and Eisenglass boat windows, leaving a non-streaking finish.Features: Safely cleans and protects against yellowing and cracking of vinyl and clear vinyl Safe for use on vinyl windows like Strataglass™ and Eisenglass Leaves a non-streak finish with no left behind residue Provides superior UV protection Made in the U.S.A. *Sold as an Individual WARNING: This product can expose you to chemicals including benzene which is known to the State of California to cause cancer, birth defects or other reproductive harm, and Ethylbenzene which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov. Specifications: Type: Vinyl & Rubber Box Dimensions: 3"H x 5"W x 12"L WT: 2.25 lbs UPC: 082043302150

    Read more

    $20.99 $16.79

  • Sale -$3.00 Springfield Taper-Lock Hi-Lo Bushing f/2-3/8" Post [2171032]

    Springfield Marine Springfield Taper-Lock Hi-Lo Bushing f/2-3/8" Post [2171032]

    Taper-Lock™ Hi-Lo Bushing for 2-3/8" PostHigh-Strength Composite Bushing Inserts Into End Of Post For Hi-Lo Seat Swivel Mount.WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

    Read more

    $15.99 $12.99

  • Sale -$38.01 Schmitt Marine Ongaro Mini Compact Twin Horn - 12V [10001]

    Schmitt Marine Schmitt Marine Ongaro Mini Compact Twin Horn - 12V [10001]

    Mini Compact Twin Horn - 12V Features: 304 Stainless Steel Trumpets, Diaphragm, and Mounting Brackets Meets ABYCA-23 for boats up to 12 meters Pre-wired Fits existing hole patterns Much louder than competitive models Specifications: Dimensions: 3"L, 8"W, 1-3/4"H (7.5 x 20.5 x 4.5 cm) Max Amp Draw: 6 Amps Rating: 112 db@ 1 Meter Specifications: Voltage - Input Range (Volts): 12v Color: Stainless Box Dimensions: 3"H x 5"W x 12"L WT: 1.55 lbs UPC: 768170100011

    Read more

    $89.00 $50.99

  • Sale -$19.74 Tecnoseal Anode Kit w/Hardware - Mercury Bravo 2-3 up to 2003 - Magnesium [20804MG]

    Tecnoseal Tecnoseal Anode Kit w/Hardware - Mercury Bravo 2-3 up to 2003 - Magnesium [20804MG]

    Mercury Bravo 2-3 Anode KitContents: (1) 00815MG (1) 00820MG (2) 00818MG Material: MagnesiumPackaging: PolybagHardware: Included Specifications: Material: Magnesium Box Dimensions: 3"H x 7"W x 8"L WT: 1.3 lbs UPC: 8059617819392 Quick Guide (pdf)Owner's Manual (pdf)

    Read more

    $57.73 $37.99

  • Sale -$126.26 Schaefer Transom Door Latch Handle - Catch Plate Included [TDH-900]

    Schaefer Marine Schaefer Transom Door Latch Handle - Catch Plate Included [TDH-900]

    Transom Door Latch Handle - Catch Plate IncludedIdeal for one handed operation of Transom Doors. 316 SS Hand Buffed and Electro-Polished. Includes Handle and Catch Plate.Specifications:  Weight 2.8 lbs (1.27kg) Length 9-5/8" (244mm) Height 2-3/4" (70mm)   Base Plate 4-1/2" (114mm) x 3-1/2" (89mm) Uses (4) 1/4" Flat Head Fasteners

    Read more

    $514.25 $387.99

  • Sale -$7.00 Trident Marine 1-1/2" Type A2 Fuel Fill Hose - Sold by the Foot [327-1126-FT]

    Trident Marine Trident Marine 1-1/2" Type A2 Fuel Fill Hose - Sold by the Foot [327-1126-FT]

    1-1/2" Type A2 Fuel Fill Hose - Sold by the FootTrident 1-1/2" ID A2 fuel fill hose for gasoline (including ethanol blends) and diesel (including bio diesel blends). Features:  Sold by the foot  This hose is built with the best fuel, fire, and age-resistant formulation  Provides extraordinary resistance to aging, fire, heat, cold, and the ozone  Also, provides excellent bend-ability Applications: Marine Fuel Hose for fill and vent plus diesel distribution Approved, for all marine fuels including gasoline, alcohol blends, diesel and bio-diesel Construction: Tube & Cover: NBR / Neoprene  Reinforcement: High tenacity polyester 2 spiral, spring steel helix Temperature Range: -20°F to 212°F (-20ºC to 100ºC)  Specifications: Inner Diameter: (inch) 1/2" / (mm) 38 Outer Diameter: (inch) 2 / (mm) 51 Wall: (inch) 0.25 / (mm) 6.4 Working Pressure: (psi) 60 / (mpa) 0.41 Bend Radius: (inch) 5.5" / (mm) 140 *The #327 series exceeds ABYC H-24 & H-33, SAE J1527, ISO 7840, & USCG Type A2; and is NMMA Type Accepted, CE certified, and Lloyds Registry Type Approved Quick Guide (pdf)

    Read more

    $19.99 $12.99

  • Sale -$4.00 Attwood Trolling Motor Quick Connectors [14367-6]

    Attwood Marine Attwood Trolling Motor Quick Connectors [14367-6]

    TM Quick ConnectorsAttwood's Trolling Motor Quick Connectors is the safe and easy quick connect / disconnect system from your trolling motor to your battery. For use where a plug and socket cannot be used. Heavy duty 10-gauge connector. Replaces battery clips 2-connector kit Safe and easy Semi-gloss finish

    Read more

    $14.99 $10.99

  • Sale -$9.01 Bennett Trim Tabs Lexan Cover [VP1138]

    Bennett Marine Bennett Trim Tabs Lexan Cover [VP1138]

    Lexan cover protects electrohydraulic unit from occasional wash down. WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

    Read more

    $27.00 $17.99

You have seen 48 out of 3419 products

Show more products

Footer image

© 2025 REBELLION MARINE, Powered by Shopify

    Login

    Forgot your password?

    Don't have an account yet?
    Create account

    Add address