Xantrex Freedon SW3024 Inverter/Charger815-302424V, 3000W - 120 Vac / 60 HzPowerful. Configurable. Versatile... The NEW GENERATION Freedom SW series represents highly sophisticated and advanced inverter/ chargers available in 3000 W with 150 A charger and 2000 W with 100 A charger models. Product DescriptionThe second generation 3000 watt model has been completely redesigned to include many of the same great features found in its high power counterpart.A key feature enhancement is 'Generator Support Mode' which enables the Freedom SW to supplement a generator when AC loads exceed the generator's capacity. The new generation models also feature improved AC transfer/AC input detection time, providing the ability to transfer AC loads to batteries in less than 10 milliseconds when the incoming grid or generator power is lost. Connected loads are almost unable to feel the power transition due to this quick transfer time. Both models are approved to UL458 with marine supplement, CSA, ABYC and FCC, Class B requirements.NEW - PARALLEL AND SERIES STACKINGParallel stacking enables the Freedom SW inverter/chargers to double the AC output in inverter mode. Series stacking enables the Freedom SW inverter/chargers to generate 120/240 V split phase output2 2 AC source must be split phase, requires Stacking Cable (part# 808-9005)ApplicationDesigned for a variety of mobile applications such as commercial, emergency and recreational vehicles, marine vessels, construction and military equipment.Product Features Pure sine wave output to operate sensitive electronics Advanced configuration options for customized applications Parallel and series stacking capability Built-in transfer switch automatically transfers between inverter power and incoming AC power Power factor corrected, multi-stage charger for fast, efficient charging Temperature compensated charging for a vareity of climate conditions Ignition lockout feature helps prevent unnecessary battery drain when the alternator is not providing power3 Wide operating temperature range: -4°F to 140°F (-20°C to 60°C) Conformal coated circuit boards for humid environments Dual input / Dual output AC interface for 3000 W model Ability to charge batteries drained to extremely low voltage Compatible with the Xantrex Automatic Generator Start4 (Part# 809-0915) 3When used with the remote panel4Sold separatelyProtection Features Battery over-voltage and under-voltage protection Over-temperature shutdown Automatic overload protection Short-circuit protection Integrated, resettable AC breakers WARNING: This product can expose you to chemicals including Diisononyl Phthalate (DINP) which is known to the State of California to cause cancer, and Di-isodecyl Phthalate (DIDP) which is known to the State of California to cause reproductive harm. For more information go to P65Warnings.ca.gov.This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns. Specifications: Charger Output - Amps: 75a Charger Output Voltage: 24v Inverter Output Voltage: 120v Inverter Input Voltage: 24v Charger Input - Voltage: 120v Outlet Qty: Optional Inverter Cont. Output Wattage: 3000w Charging Banks: 1 Box Dimensions: 13"H x 18"W x 21"L WT: 69.3 lbs UPC: 687873007673 Quick Guide (pdf)Owner's Manual (pdf)

Read more less

Freedom HF 1800Compact inverter/charger to power the comforts of home on your boat, RV, or truckWith modified sine wave output, Freedom HF 1800 inverter/charger is designed to run entertainment systems and small appliances in smaller boats, RV's and trucks. The Freedom HF inverter/charger is the smallest, lightest, and least expensive model in the Xantrex lineup.Freedom HF is designed for demanding marine and RV conditions. Temperature-controlled multistage charging ensures that your batteries are recharged safely and efficiently. Both models include an automatic transfer switch and a detachable digital remote control panel display that provides precise system information and can be mounted wherever you require the information.Product Features: Designed to power loads such as microwave ovens, TVs, DVD players, small appliances and other electronic equipment Removable digital display to provide system status Automatic three-stage battery charger Designed to be hardwired using a terminal strip, or by connecting AC through GFIC receptacles (Included) Built-in 30-amp relay to automatically transfer between inverter power and incoming AC utility power Protection Features: Battery over-voltage and under-voltage protection Over-temperature shutdown Automatic overload protection Short-circuit protection Ground-fault protection ETL listed for use in mobile RV and marine applications WARNING: This product can expose you to chemicals including Diisononyl Phthalate (DINP) which is known to the State of California to cause cancer, and Di-isodecyl Phthalate (DIDP) which is known to the State of California to cause reproductive harm. For more information go to P65Warnings.ca.gov.This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns. Specifications: Inverter Output Voltage: 120v Inverter Input Voltage: 12v Charger Input - Voltage: 120v Outlet Qty: 1 Duplex GFCI Charging Banks: 1 Inverter Cont. Output Wattage: 1800w Charger Output Voltage: 12v Charger Output - Amps: 40a Box Dimensions: 6"H x 11"W x 20"L WT: 15.4 lbs UPC: 715535890421 Quick Guide (pdf)Owner's Manual (pdf)

Read more less

PowerHub 1800A Clean, Green, Backup Power SolutionThe Xantrex PowerHub is a combination of an inverter/charger module capable of delivering up to 1800 watts of household power. It is the first backup power solution to operate with solar and wind inputs. Power from a generator or the utility grid can also be used with the PowerHub system to recharge its batteries. The PowerHub provides an affordable, high-output, primary power solution for an off-grid cottage or cabin, as well as backup power for grid-connected homes when the power goes out. It is scalable up to 400 amp-hours of energy, allowing customers to build their system based on their power requirements.Features: Never worry about running out of power – renewable power sources, solar and wind, sustain the PowerHub’s battery charge indefinitely An excellent alternative to a generator – designed for indoor use, with no fuel, fumes or noise Add it to a grid-tie solar energy system for backup power Modified sine wave inverter/charger with battery box The battery box stores up to 200 amp-hours of battery power (single battery box included; batteries purchased separately) A second battery may be connected to double the battery capacity (additional battery box and batteries sold separately) Designed to include a generator as part of the system; generator power can pass through the unit to the AC outlets, and recharge the batteries Integrated transfer switch 40-amp three-stage charger Four AC outlets with hardwire option Two DC inputs for solar and/or wind connections Full-feature LED display for system monitoring WARNING: This product can expose you to chemicals including Diisononyl Phthalate (DINP) which is known to the State of California to cause cancer, and Di-isodecyl Phthalate (DIDP) which is known to the State of California to cause reproductive harm. For more information go to P65Warnings.ca.gov.This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns. Specifications: Inverter Cont. Output Wattage: 1440w Charger Input - Voltage: 120v Charging Banks: 1 Charger Output - Amps: 40a AC Connection Type: GFCI Outlet DC Connection Type: Hardwire GFCI: Yes Outlet Qty: 2 Duplex GFCI Inverter Surge Rating: 2880w Inverter Input Voltage: 12v Inverter Output Voltage: 120v Waveform: Modified Sine Wave Charger Output Voltage: 12v Box Dimensions: 17"H x 19"W x 24"L WT: 66.45 lbs UPC: 715535114626

Read more less

Xantrex Freedon SW2012 Inverter/Charger815-201212V, 2000W - 120 Vac / 60 HzPowerful. Configurable. Versatile... The Freedom SW series represents highly sophisticated and advanced inverter/ chargers available in 3000 W with 150 A charger and 2000 W with 100 A charger models. Product DescriptionThe second generation 2000 watt model has been completely redesigned to include many of the same great features found in its high power counterpart.A key feature enhancement is 'Generator Support Mode' which enables the Freedom SW to supplement a generator when AC loads exceed the generator's capacity. The new generation models also feature improved AC transfer/AC input detection time, providing the ability to transfer AC loads to batteries in less than 10 milliseconds when the incoming grid or generator power is lost. Connected loads are almost unable to feel the power transition due to this quick transfer time. Both models are approved to UL458 with marine supplement, CSA, ABYC and FCC, Class B requirements.PARALLEL AND SERIES STACKINGParallel stacking enables the Freedom SW inverter/chargers to double the AC output in inverter mode. Series stacking enables the Freedom SW inverter/chargers to generate 120/240 V split phase output2 2 AC source must be split phase, requires Stacking Cable (part# 808-9005)ApplicationDesigned for a variety of mobile applications such as commercial, emergency and recreational vehicles, marine vessels, construction and military equipment.Product Features Pure sine wave output to operate sensitive electronics Advanced configuration options for customized applications Parallel and series stacking capability Built-in transfer switch automatically transfers between inverter power and incoming AC power Power factor corrected, multi-stage charger for fast, efficient charging Temperature compensated charging for a vareity of climate conditions Ignition lockout feature helps prevent unnecessary battery drain when the alternator is not providing power3 Wide operating temperature range: -4°F to 140°F (-20°C to 60°C) Conformal coated circuit boards for humid environments Dual input / Dual output AC interface for 3000 W model Ability to charge batteries drained to extremely low voltage Compatible with the Xantrex Automatic Generator Start4 (Part# 809-0915) 3When used with the remote panel4Sold separatelyProtection Features Battery over-voltage and under-voltage protection Over-temperature shutdown Automatic overload protection Short-circuit protection Integrated, resettable AC breakers WARNING: This product can expose you to chemicals including Diisononyl Phthalate (DINP) which is known to the State of California to cause cancer, and Di-isodecyl Phthalate (DIDP) which is known to the State of California to cause reproductive harm. For more information go to P65Warnings.ca.gov.This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns. Specifications: Charger Output - Amps: 75a Charger Output Voltage: 12v Charging Banks: 1 Outlet Qty: Optional Inverter Output Voltage: 120v Inverter Input Voltage: 12v Charger Input - Voltage: 120v Inverter Cont. Output Wattage: 2000w Box Dimensions: 13"H x 18"W x 21"L WT: 61.7 lbs UPC: 715535917036 Quick Guide (pdf)Owner's Manual (pdf)

Read more less

PT-25W Battery ChargerNewmar’s Phase Three Series Battery Chargers employ “Smart” battery charging technology for 12-volt systems aboard marine applications including workboats, military vessels, commercial vessels, and recreational craft. This charger interacts with batteries, providing the optimum three-stage charge process for fast recovery and conditioning, maximizing performance, and extending battery life.A selector switch adjusts output voltage to adapt to gel-cell, flooded lead-acid, or AGM battery types. An optional temperature compensation sensor also adjusts output for ideal voltage based on changes in the batteries’ ambient temperature. This model is housed in a rugged stainless steel case with a durable white powder coat finish, and the internal circuitry is polyurethane coated for maximum corrosion resistance.Features: 12-volt model “Smart” circuitry provides three-stage charging – bulk, absorption, and float Gel-Cell/Flooded Lead-acid/AGM battery type switch selects optimum charge/float voltages Multiple isolated output banks; ammeter indicates total output current. (Except PT-7) The optional sensor adjusts the output voltage based on battery temperature. (Except PT-7) Current limitations prevent damage from overloading Clean well-regulated output can be used as a power supply; can power loads directly without a battery in line Built to last – rugged stainless steel case with a durable white powder coat finish, an optional drip shield, and marinized internal circuitry Protection: Current Limiting, Thermal Protection, Forced Air Cooling, Drip Shield ABS-type approval for battery charging and power supplies Specifications: Input VAC (50-60 Hz.): 90-132 or 180-264 Input Amps @ Full Load: @ 115 VAC: 6.5, @ 230 VAC: 4 Power Factor: .7 Max Output Amps: 25 Output Banks: 3 Battery Capacity (Amp-Hours): 50-250 Operating Temp. Rating Reference: T-4 Case Size Reference: A-2 Case Size (H x W x D): 11.2A x 7.7 x 4.75A inches (31.8A x 19.6 x 12.1A centimeters) *Note with Dripshield installed A add 1.1” (2.8 cm) to height and .92” (2.3 cm) to depth Weight Lbs./Kg: 8.2/4 Optional Temp. Sensor Model: TCS-12/24                 Remote Panel Model: RP Equalize Option: Yes Output Indicator Reference: M-3 Compliance Reference: CG Temperature Rating References: Temperature: -20 degrees C to +60 degrees C Derate Linearly From 100% @ 50 degrees C to 60% @ 60 degrees C Nominal Output Voltages at Gel/Flooded Switch Settings (without Temperature Compensation): Gel-Cell: 14.0 VDC Charge @ 50% load and 13.6 VDC Float @ .5 amp load Flooded/AGM: 14.2 VDC Charge @ 50% load and 13.4 VDC Float @ .5 amp load Compliance References: CG: USCG CFR 183.410 (Ignition protected) CE: Carries the CE mark ABS: PT Series meets SVR 2009 4-8-3/5.9, Under 90 meters Rules 2006 4-6-4/7.19, and HSNC 2007 4-8-3/5.13. Options: Remote Panel, model RP, for use with all models except PT-7 and PT-40U (LEDs indicate charger output stage. Manual re-initialization of three-stage charge cycle. With 25′ of cable. Panel dimensions: 3″ H x 4.75″ W) Temperature Compensation Sensor, Model TCS 12/24, for use with all models except PT 7 (-5 mV per cell degrees C, 25′ cable (40’cable optional) This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns. Specifications: Charger Input - Voltage: 115/230v Charger Output - Amps: 25a Charger Output Voltage: 12v Charging Banks: 3 Inverter Input Voltage: 115/230v Inverter Output Voltage: 12v Outlet Qty: Hardwire Portable: No Box Dimensions: 10"H x 10"W x 16"L WT: 9.5 lbs Owner's Manual (pdf)

Read more less

PT-24-8W Battery Charger“Smart” marine battery charging technology for 24-volt systems aboard workboats, military vessels, commercial vessels, and recreational craft. This charger interacts with batteries, providing the optimum three-stage charge process for fast recovery and conditioning, maximizing performance, and extending battery life.A selector switch adjusts output voltage to adapt to gel-cell, flooded lead-acid, or AGM battery types. An optional temperature compensation sensor also adjusts output for ideal voltage based on changes in the batteries’ ambient temperature. All models are housed in a rugged stainless steel case with a durable white powder coat finish, and the internal circuitry is polyurethane coated for maximum corrosion resistance.Features: 24-volt model “Smart” circuitry provides three-stage charging – bulk, absorption, float Gel-Cell/Flooded Lead-acid/AGM battery type switch selects optimum charge/float voltages Multiple isolated output banks; ammeter indicates total output current The optional sensor adjusts output voltage based on battery temperature Current limiting prevents damage from overloading Use as a power supply; can power loads without a battery in line Built to last – rugged stainless steel case with a durable white powder coat finish with an optional drip shield and marinized internal circuitry Protection: Current Limiting, Thermal Protection, Forced Air Cooling, Drip Shield Install in conjunction with PT-MCU for additional control and monitoring ABS-type approval for battery charging and power supplies Specifications: Input VAC (50-60 Hz.): 85 – 264 Input Amps @ Full Load: @ 115 VAC: 2.8, @ 230 VAC: 1.4 Power Factor: .98@115V and .93@230V Max Output Amps: 8 Output Banks: 3 Battery Capacity (Amp-Hours): 16 – 80 Operating Temp. Rating Reference: T-1 Case Size Reference: A-1 Case Size (H x W x D): 11.2A x 7.7 x 4.75A inches (28.4A x 19.6 x 12.1A centimeters) *Note with Dripshield installed A add 1.1” (2.8 cm) to height and .92” (2.3 cm) to depth Weight Lbs./Kg: 8/4 Optional Temp. Sensor Model: TCS-12/24         Remote Panel Model: RP Compliance Reference: CG, CE, ABS Temperature Rating References: Temperature: -10 degrees C to +60 degrees C Derate Linearly From 100% @ 40 degrees C to 60% @ 60 degrees C Nominal Output Voltages at Gel/Flooded Switch Settings (without Temperature Compensation): Gel-Cell: 28.0 VDC Charge @ 50% load and 27.2 VDC Float @ .5 amp load Flooded/AGM: 28.4 VDC Charge @ 50% load and 26.8 VDC Float @ .5 amp load Compliance References: UL: UL 1950 (per DNB report) CG: USCG CFR 183.410 (Ignition protected) EN: EN 60335-1 CE: Carries the CE mark ABS: PT Series meets SVR 2009 4-8-3/5.9, Under 90 meters Rules 2006 4-6-4/7.19, and HSNC 2007 4-8-3/5.13. Options:Remote Panel, model RP, for use with all models except PT-24-20U, PT-24-60, and PT-32-25 (LEDs indicate charger output stage. Manual re-initialization of three-stage charge cycle. With 25′ of cable. Panel dimensions: 3″ H x 4.75″ W)This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns. Specifications: Charger Input - Voltage: 115/230v Charger Output - Amps: 8a Charger Output Voltage: 24v Charging Banks: 3 Inverter Input Voltage: 115/230v Inverter Output Voltage: 24v Outlet Qty: Hardwire Portable: No Box Dimensions: 10"H x 10"W x 16"L WT: 8.3 lbs Quick Guide (pdf)Owner's Manual (pdf)

Read more less

PT-24-13W Battery Charger“Smart” marine battery charging technology for 24-volt systems aboard workboats, military vessels, commercial vessels, and recreational craft. This charger interacts with batteries, providing the optimum three-stage charge process for fast recovery and conditioning, maximizing performance, and extending battery life.A selector switch adjusts output voltage to adapt to gel-cell, flooded lead-acid, or AGM battery types. An optional temperature compensation sensor also adjusts output for ideal voltage based on changes in the batteries’ ambient temperature. All models are housed in a rugged stainless steel case with a durable white powder coat finish, and the internal circuitry is polyurethane coated for maximum corrosion resistance.Features: 24-volt model “Smart” circuitry provides three-stage charging – bulk, absorption, float Gel-Cell/Flooded Lead-acid/AGM battery type switch selects optimum charge/float voltages Multiple isolated output banks; ammeter indicates total output current The optional sensor adjusts output voltage based on battery temperature Current limiting prevents damage from overloading Use as a power supply; can power loads without a battery in line Built to last – rugged stainless steel case with a durable white powder coat finish with an optional drip shield and marinized internal circuitry Protection: Current Limiting, Thermal Protection, Forced Air Cooling, Drip Shield Install in conjunction with PT-MCU for additional control and monitoring ABS-type approval for battery charging and power supplies Specifications: Input VAC (50-60 Hz.): 90 – 132, 180 – 264 Input Amps @ Full Load: @ 115 VAC: 6.5, @ 230 VAC: 4  Power Factor: .7 Max Output Amps: 13 Output Banks: 3 Battery Capacity (Amp-Hours): 26 – 130 Operating Temp. Rating Reference: T-2 Case Size Reference: A-1 Case Size (H x W x D): 11.2A x 7.7 x 4.75A inches (28.4A x 19.6 x 12.1A centimeters) *Note with Dripshield installed A add 1.1” (2.8 cm) to height and .92” (2.3 cm) to depth Weight Lbs./Kg: 8/4 Optional Temp. Sensor Model: TCS-12/24     Remote Panel Model: RP Compliance Reference: CG, ABS  Temperature Rating References: Temperature: -10 degrees C to +60 degrees C     Derate Linearly From 100% @ 50 degrees C to 60% @ 60 degrees C Nominal Output Voltages at Gel/Flooded Switch Settings (without Temperature Compensation): Gel-Cell: 28.0 VDC Charge @ 50% load and 27.2 VDC Float @ .5 amp load Flooded/AGM: 28.4 VDC Charge @ 50% load and 26.8 VDC Float @ .5 amp load Compliance References: UL: UL 1950 (per DNB report) CG: USCG CFR 183.410 (Ignition protected) EN: EN 60335-1 CE: Carries the CE mark ABS: PT Series meets SVR 2009 4-8-3/5.9, Under 90 meters Rules 2006 4-6-4/7.19, and HSNC 2007 4-8-3/5.13. Options:Remote Panel, model RP, for use with all models except PT-24-20U, PT-24-60, and PT-32-25 (LEDs indicate charger output stage. Manual re-initialization of three-stage charge cycle. With 25′ of cable. Panel dimensions: 3″ H x 4.75″ W)This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns. Specifications: Charger Input - Voltage: 115/230v Charger Output - Amps: 13a Charger Output Voltage: 24v Charging Banks: 3 Inverter Input Voltage: 115/230v Inverter Output Voltage: 24v Outlet Qty: Hardwire Portable: No Box Dimensions: 10"H x 10"W x 16"L WT: 9 lbs Owner's Manual (pdf)

Read more less

PT-80 Battery ChargerNewmar’s Phase Three Series Battery Chargers employ “Smart” battery charging technology for 12-volt systems aboard marine applications including workboats, military vessels, commercial vessels, and recreational craft. This charger interacts with batteries, providing the optimum three-stage charge process for fast recovery and conditioning, maximizing performance, and extending battery life.A selector switch adjusts output voltage to adapt to gel-cell, flooded lead-acid, or AGM battery types. An optional temperature compensation sensor also adjusts output for ideal voltage based on changes in the batteries’ ambient temperature. This model is housed in a rugged stainless steel case with a durable white powder coat finish, and the internal circuitry is polyurethane coated for maximum corrosion resistance.Features: 12-volt model “Smart” circuitry provides three-stage charging – bulk, absorption, and float Gel-Cell/Flooded Lead-acid/AGM battery type switch selects optimum charge/float voltages Multiple isolated output banks; ammeter indicates total output current. (Except PT-7) The optional sensor adjusts the output voltage based on battery temperature. (Except PT-7) Current limitations prevent damage from overloading Clean well-regulated output can be used as a power supply; can power loads directly without a battery in line Built to last – rugged stainless steel case with a durable white powder coat finish, an optional drip shield, and marinized internal circuitry Protection: Current Limiting, Thermal Protection, Forced Air Cooling, Drip Shield ABS-type approval for battery charging and power supplies Specifications: Input VAC (50-60 Hz.): 90-264 Input Amps @ Full Load: @ 115 VAC: 12, @ 230 VAC: 7 Power Factor: .95@230V or .98@115V Max Output Amps: 80 Output Banks: 3 Battery Capacity (Amp-Hours): 160-800 Operating Temp. Rating Reference: T-7 Case Size Reference: A-5 Case Size (H x W x D): 16.8C x 9.6 x 6.1C inches (42.7C x 24.4 x 15.5C centimeters) *Note with Dripshield installed C add 1” (2.54 cm) to height and .5” (1.27 cm) to depth Weight Lbs./Kg: 15.2/7 Optional Temp. Sensor Model: TCS-12/24                 Remote Panel Model: RP Equalize Option: Yes Output Indicator Reference: M-3 Compliance Reference: CE Temperature Rating References: Temperature: -10 degrees C to +60 degrees C Derate Linearly From 100% @ 50 degrees C to 80% @ 60 degrees C Nominal Output Voltages at Gel/Flooded Switch Settings (without Temperature Compensation): Gel-Cell: 14.0 VDC Charge @ 50% load and 13.6 VDC Float @ .5 amp load Flooded/AGM: 14.2 VDC Charge @ 50% load and 13.4 VDC Float @ .5 amp load Compliance References: CG: USCG CFR 183.410 (Ignition protected) CE: Carries the CE mark ABS: PT Series meet SVR 2009 4-8-3/5.9, Under 90 meters Rules 2006 4-6-4/7.19, and HSNC 2007 4-8-3/5.13 Options: Remote Panel, model RP, for use with all models except PT-7 and PT-40U (LEDs indicate charger output stage. Manual re-initialization of three-stage charge cycle. With 25′ of cable. Panel dimensions: 3″ H x 4.75″ W) Temperature Compensation Sensor, Model TCS 12/24, for use with all models except PT 7 (-5 mV per cell degrees C, 25′ cable (40’cable optional) This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns. Specifications: Charger Input - Voltage: 115/230v Charger Output - Amps: 80a Charger Output Voltage: 12v Charging Banks: 3 Inverter Input Voltage: 115/230v Inverter Output Voltage: 12v Outlet Qty: Hardwire Portable: No Box Dimensions: 11"H x 15"W x 20"L WT: 18 lbs Quick Guide (pdf)Owner's Manual (pdf)

Read more less

Freedom HF 1000Compact inverter/charger to power the comforts of home on your boat, RV, or truckWith modified sine wave output, Freedom HF 1000 inverter/charger is designed to run entertainment systems and small appliances in smaller boats, RV's and trucks. The Freedom XMIC inverter/charger is the smallest, lightest, and least expensive model in the Xantrex lineup.Freedom HF is designed for demanding marine and RV conditions. Temperature-controlled multistage charging ensures that your batteries are recharged safely and efficiently. Both models include an automatic transfer switch and a detachable digital remote control panel display that provides precise system information and can be mounted wherever you require the information.Product Features: Designed to power loads such as microwave ovens, TVs, DVD players, small appliances and other electronic equipment Removable digital display to provide system status Automatic three-stage battery charger Designed to be hardwired using a terminal strip, or by connecting AC through GFIC receptacles (Included) Built-in 30-amp relay to automatically transfer between inverter power and incoming AC utility power Protection Features: Battery over-voltage and under-voltage protection Over-temperature shutdown Automatic overload protection Short-circuit protection Ground-fault protection ETL listed for use in mobile RV and marine applications WARNING: This product can expose you to chemicals including Diisononyl Phthalate (DINP) which is known to the State of California to cause cancer, and Di-isodecyl Phthalate (DIDP) which is known to the State of California to cause reproductive harm. For more information go to P65Warnings.ca.gov.This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns. Specifications: Inverter Output Voltage: 120v Inverter Input Voltage: 12v Charger Input - Voltage: 120v Outlet Qty: 1 Duplex GFCI Charging Banks: 1 Inverter Cont. Output Wattage: 1000w Charger Output Voltage: 12v Charger Output - Amps: 20a Box Dimensions: 6"H x 11"W x 18"L WT: 12.95 lbs UPC: 715535890414 Quick Guide (pdf)Owner's Manual (pdf)

Read more less

PT-24-45U Battery Charger“Smart” marine battery charging technology for 24-volt systems aboard workboats, military vessels, commercial vessels, and recreational craft. This charger interacts with batteries, providing the optimum three-stage charge process for fast recovery and conditioning, maximizing performance, and extending battery life.A selector switch adjusts output voltage to adapt to gel-cell, flooded lead-acid, or AGM battery types. An optional temperature compensation sensor also adjusts output for ideal voltage based on changes in the batteries’ ambient temperature. All models are housed in a rugged stainless steel case with a durable white powder coat finish, and the internal circuitry is polyurethane coated for maximum corrosion resistance.Features: 24-volt model “Smart” circuitry provides three-stage charging – bulk, absorption, float Gel-Cell/Flooded Lead-acid/AGM battery type switch selects optimum charge/float voltages Multiple isolated output banks; ammeter indicates total output current The optional sensor adjusts output voltage based on battery temperature Current limiting prevents damage from overloading Use as a power supply; can power loads without a battery in line Built to last – rugged stainless steel case with a durable white powder coat finish with an optional drip shield and marinized internal circuitry Protection: Current Limiting, Thermal Protection, Forced Air Cooling, Drip Shield Install in conjunction with PT-MCU for additional control and monitoring ABS-type approval for battery charging and power supplies Specifications: Input VAC (50-60 Hz.): 90 – 264 Input Amps @ Full Load: @ 115 VAC: 12, @ 230 VAC: 7  Power Factor: .98@115V and .95@230V Max Output Amps: 45 Output Banks: 3 Battery Capacity (Amp-Hours): 90 – 450 Operating Temp. Rating Reference: T-5 Case Size Reference: A-4 Case Size (H x W x D): 14.8B x 9.6 x 5.6D inches (37.6D x 24.4 x 14.2D centimeters) *Note with Dripshield installed D add 1” (2.54 cm) to height and .5” (1.2 cm) to depth Weight Lbs./Kg: 12/6 Optional Temp. Sensor Model: TCS-12/24     Remote Panel Model: RP Compliance Reference: EN, CE, ABS Temperature Rating References: Temperature: -20 degrees C to +70 degrees C     Derate Linearly From 100% @ 50 degrees C to 50% @ 70 degrees C Nominal Output Voltages at Gel/Flooded Switch Settings (without Temperature Compensation): Gel-Cell: 28.0 VDC Charge @ 50% load and 27.2 VDC Float @ .5 amp load Flooded/AGM: 28.4 VDC Charge @ 50% load and 26.8 VDC Float @ .5 amp load Compliance References: UL: UL 1950 (per DNB report) CG: USCG CFR 183.410 (Ignition protected) EN: EN 60335-1 CE: Carries the CE mark ABS: PT Series meets SVR 2009 4-8-3/5.9, Under 90 meters Rules 2006 4-6-4/7.19, and HSNC 2007 4-8-3/5.13. Options:Remote Panel, model RP, for use with all models except PT-24-20U, PT-24-60, and PT-32-25 (LEDs indicate charger output stage. Manual re-initialization of three-stage charge cycle. With 25′ of cable. Panel dimensions: 3″ H x 4.75″ W)This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns. Specifications: Charger Input - Voltage: 115/230v Charger Output - Amps: 45a Charger Output Voltage: 24v Charging Banks: 3 Inverter Input Voltage: 115/230v Inverter Output Voltage: 24v Outlet Qty: Hardwire Portable: No Box Dimensions: 10"H x 14"W x 20"L WT: 18 lbs Quick Guide (pdf)Owner's Manual (pdf)

Read more less

PT-14W Battery ChargerNewmar’s Phase Three Series Battery Chargers employ “Smart” battery charging technology for 12-volt systems aboard marine applications including workboats, military vessels, commercial vessels, and recreational craft. This charger interacts with batteries, providing the optimum three-stage charge process for fast recovery and conditioning, maximizing performance, and extending battery life.A selector switch adjusts output voltage to adapt to gel-cell, flooded lead-acid, or AGM battery types. An optional temperature compensation sensor also adjusts output for ideal voltage based on changes in the batteries’ ambient temperature. This model is housed in a rugged stainless-steel case with a durable white powder coat finish, and the internal circuitry is polyurethane-coated for maximum corrosion resistance.Features: “Smart” circuitry provides three-stage charging – bulk, absorption, float Gel-Cell/Flooded Lead-acid/AGM battery type switch selects optimum charge/float voltages Multiple isolated output banks; ammeter indicates total output current. (Except PT-7) The optional sensor adjusts output voltage based on battery temperature. (Except PT-7) Current limiting prevents damage from overloading Clean well-regulated output can be used as a power supply; can power loads directly without a battery in line Built to last – rugged stainless-steel case with a durable white powder coat finish with an optional drip shield and marinized internal circuitry Protection: Current Limiting, Thermal Protection, Forced Air Cooling, Drip Shield ABS-type approval for battery charging and power supplies Specifications: Input VAC (50-60 Hz.): 85-264     Input Amps @ Full Load: @ 115 VAC: 2.8, @ 230 VAC: 1.4  P.F. Rating: .93@230V and .98@115V Max Output Amps: 14 Output Banks: 3 Battery Capacity (Amp-Hours): 28-140     Operating Temp. Rating Reference: T-2 Case Size Reference: A-2 Case Size (H x W x D): 11.2A x 7.7 x 4.75A inches (31.8A x 19.6 x 12.1A centimeters) *Note with Dripshield installed A add 1.1” (2.8 cm) to height and .92” (2.3 cm) to depth Weight Lbs./Kg: 8/4 Optional Temp. Sensor Model: TCS-12/24     Remote Panel Model: RP Equalize Option: Yes Output Indicator Reference: M-3 Compliance Reference: CG, CE     Temperature Rating References: Temperature: -10 degrees C to +60 degrees C     Derate Linearly From 100% @ 40 degrees C to 60% @ 60 degrees C Nominal Output Voltages at Gel/Flooded Switch Settings (without Temperature Compensation): Gel-Cell: 14.0 VDC Charge @ 50% load and 13.6 VDC Float @ .5 amp load Flooded/AGM: 14.2 VDC Charge @ 50% load and 13.4 VDC Float @ .5 amp load Compliance References: CG: USCG CFR 183.410 (Ignition protected) CE: Carries the CE mark ABS: PT Series meets SVR 2009 4-8-3/5.9, Under 90 meters Rules 2006 4-6-4/7.19, and HSNC 2007 4-8-3/5.13. Options:Remote Panel, model RP, for use with all models except PT-7 and PT-40U (LEDs indicate the charger output stage. Manual re-initialization of a three-stage charge cycle. With 25′ of cable. Panel dimensions: 3″ H x 4.75″ W)This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns. Specifications: Charger Input - Voltage: 115/230v Charger Output - Amps: 14a Charger Output Voltage: 12v Charging Banks: 3 Inverter Input Voltage: 115/230v Inverter Output Voltage: 115/230v Outlet Qty: Hardwire Portable: No Box Dimensions: 11"H x 11"W x 16"L WT: 9.5 lbs Quick Guide (pdf)Owner's Manual (pdf)

Read more less

PT-24-95U Battery Charger“Smart” marine battery charging technology for 24-volt systems aboard workboats, military vessels, commercial vessels, and recreational craft. This charger interacts with batteries, providing the optimum three-stage charge process for fast recovery and conditioning, maximizing performance, and extending battery life.A selector switch adjusts output voltage to adapt to gel-cell, flooded lead-acid, or AGM battery types. An optional temperature compensation sensor also adjusts output for ideal voltage based on changes in the batteries’ ambient temperature. All models are housed in a rugged stainless steel case with a durable white powder coat finish, and the internal circuitry is polyurethane coated for maximum corrosion resistance.Features: 24-volt model “Smart” circuitry provides three-stage charging – bulk, absorption, float Gel-Cell/Flooded Lead-acid/AGM battery type switch selects optimum charge/float voltages Multiple isolated output banks; ammeter indicates total output current The optional sensor adjusts output voltage based on battery temperature Current limiting prevents damage from overloading Use as a power supply; can power loads without a battery in line Built to last – rugged stainless steel case with a durable white powder coat finish with an optional drip shield and marinized internal circuitry Protection: Current Limiting, Thermal Protection, Forced Air Cooling, Drip Shield Install in conjunction with PT-MCU for additional control and monitoring ABS-type approval for battery charging and power supplies Specifications: Input VAC (50-60 Hz.): 90-264 Input Amps @ Full Load: @ 115 VAC: 26, @ 230 VAC: 14 Power Factor: .98@115V and .95@230V Max Output Amps: 95 Output Banks: 3 Battery Capacity (Amp-Hours): 180 – 950 Operating Temp. Rating Reference: T-5 Case Size Reference: A-5 Case Size (H x W x D): 17.5E x 12 x 7.2E inches (44.5E x 30.5 x 18.3E centimeters) *Note with Dripshield installed E add 2” (5.08 cm) to height and 1” (2.54 cm) to depth Weight Lbs./Kg: 24.5/11 Optional Temp. Sensor Model: TCS-12/24             Remote Panel Model: RP Compliance Reference: EN, CE, ABS Temperature Rating References: Temperature: -20 degrees C to +70 degrees C Derate Linearly From 100% @ 50 degrees C to 50% @ 70 degrees C Nominal Output Voltages at Gel/Flooded Switch Settings (without Temperature Compensation): Gel-Cell: 28.0 VDC Charge @ 50% load and 27.2 VDC Float @ .5 amp load Flooded/AGM: 28.4 VDC Charge @ 50% load and 26.8 VDC Float @ .5 amp load Compliance References: UL: UL 1950 (per DNB report) CG: USCG CFR 183.410 (Ignition protected) EN: EN 60335-1 CE: Carries the CE mark ABS: PT Series meets SVR 2009 4-8-3/5.9, Under 90 meters Rules 2006 4-6-4/7.19, and HSNC 2007 4-8-3/5.13. Options:Remote Panel, model RP, for use with all models except PT-24-20U, PT-24-60, and PT-32-25 (LEDs indicate charger output stage. Manual re-initialization of three-stage charge cycle. With 25′ of cable. Panel dimensions: 3″ H x 4.75″ W)This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns. Specifications: Charger Input - Voltage: 115/230v Charger Output - Amps: 95a Charger Output Voltage: 24v Charging Banks: 3 Inverter Input Voltage: 115/230v Inverter Output Voltage: 24v Outlet Qty: Hardwire Portable: No Box Dimensions: 12"H x 17"W x 26"L WT: 31.5 lbs Quick Guide (pdf)Owner's Manual (pdf)

Read more less

Freedom 458 Inverter/ChargerAC Power Inverter with High Surge Capability, 3-Stage ChargerWith filtered modified sine wave output, Freedom inverter/chargers run virtually anything, from electrical equipment to appliances and electronics in your RV. Temperature controlled multistage charging ensures that your batteries are recharged quickly, and automatic shutdown and other safety features protect your expensive deep-cycle batteries from excessive depletion. For inverter/charger control and basic system monitoring, use the Freedom Basic Remote. For advanced battery monitoring and remote control, Freedom 458 systems can be paired with optional Link instrumentation.Product Features MSW AC power inverter with high surge capability Automatic 3-stage battery charger Temperature compensation with equalization stage provides optimal charging of deep cycle batteries Built-in transfer switch automatically transfers between inverter power and incoming AC power Power sharing prevents source AC input circuit breaker from tripping Customized settings can be programmed with the Freedom Basic Remote or Link 1000 panels Includes battery temperature sensor 30 month warranty Protection Features Over voltage and under voltage protection Over-temperature protection Overload protection Short circuit protection Electrical Specifications - Inverter Output power (continuous): 2000W Surge power (AC amps): 50A Output frequency regulation: 60Hz Inverter voltage regulation: 120V +/-5% true RMS Output wave form: Modified sine wave Efficiency (full load): 85% Peak efficiency: 92% No load current draw (idle mode): 0.12A AC output connections: Dual - 20/15 Circuit Breakers AC input connections: Single AC transfer switch: 30A Electrical Specifications - Charger Charge rate: 100A DC AC input voltage range: 90 130 VAC Battery voltage (nominal): 12 VDC Battery voltage range: 10.0 15.5 VDC Low battery cut-out: 10.0 VDC AC input (max. charge mode): 21A AC Bulk charge voltage: 14.3 VDC*** Float charge voltage: 13.4 VDC*** Equalize charge voltage: 16.3 VDC Charge control: 3-stage Battery type settings: Wet / Gel 1 / Gel 2 / AGM Equalization: Yes Temperature sensitive charging: Yes ***Default value varies with battery type and temperatureWARNING: This product can expose you to chemicals including Diisononyl Phthalate (DINP) which is known to the State of California to cause cancer, and Di-isodecyl Phthalate (DIDP) which is known to the State of California to cause reproductive harm. For more information go to P65Warnings.ca.gov.This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns. Specifications: Outlet Qty: None Charging Banks: 1 Inverter Output Voltage: 120v Inverter Input Voltage: 12v Charger Input - Voltage: 120v Inverter Cont. Output Wattage: 2000w Charger Output Voltage: 12v Charger Output - Amps: 100a Box Dimensions: 13"H x 15"W x 19"L WT: 55.7 lbs UPC: 647912106149 Owner's Manual (pdf)Brochure (pdf)

Read more less

Freedom 458 Inverter/Charger - 2000W120 Vac / 60 HzWith filtered modified sine wave output, the Freedom 458 inverter/charger has the ability to run electrical equipment, appliances and even sensitive electronics. Perfect for any RV, the temperature controlled multistage charging ensures that your batteries are recharged quickly, and safety features such as automatic shut down protects your expensive deep-cycle batteries from excessive depletion.AC Power Inverter with High Surge Capability, 3-Stage ChargerWith filtered modified sine wave output, Freedom inverter/chargers run virtually anything, from electrical equipment to appliances and electronics in your RV. Temperature controlled multistage charging ensures that your batteries are recharged quickly, and automatic shutdown and other safety features protect your expensive deep-cycle batteries from excessive depletion.For inverter/charger control and basic system monitoring, use the Freedom Basic Remote. For advanced battery monitoring and remote control, Freedom 458 systems can be paired with optional Link instrumentation.Product Features: MSW AC power inverter with high surge capability Automatic 3-stage battery charger Temperature compensation with equalization stage provides optimal charging of deep cycle batteries Built-in transfer switch automatically transfers between inverter power and incoming AC power Power sharing prevents source AC input circuit breaker from tripping Customized settings can be programmed with the Freedom Basic Remote or Link 1000 panels Includes battery temperature sensor 30 month warranty Hardwired AC Output (Single In/Single Out) Protection Features: Over voltage and under voltage protection Over-temperature protection Overload protection Short circuit protection WARNING: This product can expose you to chemicals including Diisononyl Phthalate (DINP) which is known to the State of California to cause cancer, and Di-isodecyl Phthalate (DIDP) which is known to the State of California to cause reproductive harm. For more information go to P65Warnings.ca.gov.This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns. Specifications: Charger Output Voltage: 12v Charger Output - Amps: 100a Inverter Output Voltage: 120v Inverter Input Voltage: 12v Charger Input - Voltage: 120v Inverter Cont. Output Wattage: 2000w Outlet Qty: None Charging Banks: 1 Box Dimensions: 12"H x 15"W x 19"L WT: 55 lbs UPC: 647912105630 Quick Guide (pdf)Owner's Manual (pdf)

Read more less

Xantrex Freedom SW3012 Inverter/Charger815-301212V, 3000W - 120 Vac / 60 HzPowerful. Configurable. Versatile... The NEW GENERATION Freedom SW series represents highly sophisticated and advanced inverter/ chargers available in 3000 W with 150 A charger and 2000 W with 100 A charger models. Product DescriptionThe second generation 3000 watt model has been completely redesigned to include many of the same great features found in its high power counterpart.A key feature enhancement is 'Generator Support Mode' which enables the Freedom SW to supplement a generator when AC loads exceed the generator's capacity. The new generation models also feature improved AC transfer/AC input detection time, providing the ability to transfer AC loads to batteries in less than 10 milliseconds when the incoming grid or generator power is lost. Connected loads are almost unable to feel the power transition due to this quick transfer time. Both models are approved to UL458 with marine supplement, CSA, ABYC and FCC, Class B requirements.NEW - PARALLEL AND SERIES STACKINGParallel stacking enables the Freedom SW inverter/chargers to double the AC output in inverter mode. Series stacking enables the Freedom SW inverter/chargers to generate 120/240 V split phase output2 2 AC source must be split phase, requires Stacking Cable (part# 808-9005)ApplicationDesigned for a variety of mobile applications such as commercial, emergency and recreational vehicles, marine vessels, construction and military equipment.Product Features Pure sine wave output to operate sensitive electronics Advanced configuration options for customized applications Parallel and series stacking capability Built-in transfer switch automatically transfers between inverter power and incoming AC power Power factor corrected, multi-stage charger for fast, efficient charging Temperature compensated charging for a vareity of climate conditions Ignition lockout feature helps prevent unnecessary battery drain when the alternator is not providing power3 Wide operating temperature range: -4°F to 140°F (-20°C to 60°C) Conformal coated circuit boards for humid environments Dual input / Dual output AC interface for 3000 W model Ability to charge batteries drained to extremely low voltage Compatible with the Xantrex Automatic Generator Start4 (Part# 809-0915) 3When used with the remote panel4Sold separatelyProtection Features Battery over-voltage and under-voltage protection Over-temperature shutdown Automatic overload protection Short-circuit protection Integrated, resettable AC breakers WARNING: This product can expose you to chemicals including Diisononyl Phthalate (DINP) which is known to the State of California to cause cancer, and Di-isodecyl Phthalate (DIDP) which is known to the State of California to cause reproductive harm. For more information go to P65Warnings.ca.gov.This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns. Specifications: Charger Output Voltage: 12v Inverter Output Voltage: 120v Inverter Input Voltage: 12v Charger Input - Voltage: 120v Outlet Qty: Optional Charging Banks: 1 Inverter Cont. Output Wattage: 3000w Charger Output - Amps: 150a Box Dimensions: 12"H x 18"W x 21"L WT: 69.4 lbs UPC: 008153012413 Quick Guide (pdf)Owner's Manual (pdf)

Read more less