Black Nylon Wire Tie MountThe AT-3 tie mount is smaller for panel and other small space applications. This part is molded in black nylon and is sized for a #3 wire tie with a maximum width of .20". Average pull strength is about 50 lbs. The square base measures .44" wide. Use this smaller wire tie for runs with only a few wires or where space prevents use of our larger tie mounts. Excellent for mounting compass wires on center console boats and for overhead panel runs.

Read more less

Executive Fastener Kit - No AdhesiveThis Kit Contains A Large Selection Of All The Common Weld Mount Parts And Is An Ideal Kit For The Full Service Yard Or Custom Builder. The Kit Does NOT Contain Acrylic Adhesive The Weld Mount System Eliminates The Need To Drill Into Cored Composites Which Can Result In Hull & Deck Delaminations. No Need To Drill, Tap, or Weld When Used On Metal Surfaces. Great For Mounting Electronics, Wire Runs, Bilge Applications, Water Separators, Battery Switches, Etc. The AT-1001008 Kit Contains: (1) AT-300 - Dispensing Gun (10) AT-850 - 3.5" Mixing Tips For AT-8040 Adhesive (100) AT-5 - Large White Cable Tie Mount (50) AT-3 - Small White Cable Tie Mount (4) AT-113 - Large Footman's Strap (10) PS62-832-16SS - 1.00" Long Panel Stud (4) ST125-1420-16SS - 1.00" Long Stud With 1/4 x 20 Threads 1.25" Base (4) ST125-1420-24SS - 1.50" Long Stud With 1/4 x 20 Threads 1.25" Base (4) ST125-1024-12SS - .75" Long Stud With #10 x 24 Threads 1.25" Base (4) ST125-1024-24SS - 1.50" Long Stud With #10 x 24 Threads 1.25" Base (1) Plano Storage Box 14" x 9" x 2.75" Step By Step Instructions

Read more less

Executive Adhesive & Fastener Kit w/AT-8040 AdhesiveThis Kit Contains A Large Selection Of All The Common Weld Mount Parts And Is An Ideal Kit For The Full Service Yard Or Custom Builder. The Kit Contains 1 Tube Of Our AT-8040 No Slide Multi Bonder Acrylic Adhesive Which Will Bond To Almost All Surfaces Except Low Energy Plastic Or Rubber. AT-8040 Will Hold Even Our Heaviest Parts on a Vertical or Overhead Surface Without Fixturing. The Adhesive Sets in 12 Minutes And Is Heat Resistant To 225°. The Adhesive Should Be Refrigerated and Has A Shelf Life Of 1 year.The Weld Mount System Eliminates The Need To Drill Into Cored Composites Which Can Result In Hull & Deck Delaminations. No Need To Drill, Tap, or Weld When Used On Metal Surfaces. Great For Mounting Electronics, Wire Runs, Bilge Applications, Water Separators, Battery Switches, Etc.The AT-1001003 Kit Contains: (1) AT-8040 - No Slide Multi Bonder Acrylic Adhesive (1) AT-300 - Dispensing Gun (10) AT-850 - 3.5" Mixing Tips For AT-8040 Adhesive (100) AT-5 - Large White Cable Tie Mount (50) AT-3 - Small White Cable Tie Mount (4) AT-113 - Large Footman's Strap (10) PS62-832-16SS - 1.00" Long Panel Stud (4) ST125-1420-16SS - 1.00" Long Stud With 1/4 x 20 Threads 1.25" Base (4) ST125-1420-24SS - 1.50" Long Stud With 1/4 x 20 Threads 1.25" Base (4) ST125-1024-12SS - .75" Long Stud With #10 x 24 Threads 1.25" Base (4) ST125-1024-24SS - 1.50" Long Stud With #10 x 24 Threads 1.25" Base (1) Plano Storage Box 14" x 9" x 2.75" Step By Step Instructions Quick Guide (pdf)Owner's Manual (pdf)

Read more less

Spanner Wrench/Deck Plate Key Features:Cast bronze with stainless steel pins to fit 1/4" and 5/16" holes.  Opens to service deck plates or strainer caps with key holes up to 7" apart.  Hangs conveniently near the strainer(s) location.   C83600 bronze

Read more less

Prop Wrench Set - Fits 17/32" to 1-1/4" Prop NutsMultiple socket sizes for all prop maintenance. Offers multiple sockets to fit from 17/32" to 1-1/4", allowing consumers to service multiple props Built of durable plastic WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Material: Plastic Box Dimensions: 1"H x 7"W x 16"L WT: 1 lbs UPC: 022697137074

Read more less

1" Tall Stainless Stud w/#8 x 32 ThreadOur Small Stainless Steel Panel Studs have a wide range of uses. Originally they were used for mounting on the backside of dash panels for mounting to the console. Now they are used for securing a wide range of wire clamps and other small components to composite surfaces. The base plate is 0.62" in diameter with a 1" tall stud. Tensile strength is 300 lbs. and shear strength is 375 lbs. Maximum torque load is 45 inch/lbs.

Read more less

.75" Tall Stainless Stud w/#8 x 32 ThreadOur Small Stainless Steel Panel Studs have a wide range of uses. Originally they were used for mounting on the backside of dash panels for mounting to the console. Now they are used for securing a wide range of wire clamps and other small components to composite surfaces. The base plate is 0.62" in diameter with a .75" tall stud. Tensile strength is 300 lbs. and shear strength is 375 lbs. Maximum torque load is 45 inch/lbs.

Read more less

AT-3 Small White Nylon Tie Mount - Qty. 500The AT-3 tie mount is smaller for panel and other small space applications. This part is molded in white nylon and is sized for a #3 wire tie with a maximum width of .20". Average pull strength is about 50 lbs. The square base measures .44" wide. Use this smaller wire tie for runs with only a few wires or where space prevents use of our larger tie mounts. Excellent for mounting compass wires on center console boats and for overhead panel runs.

Read more less

1.25" Tall Stainless Stud w/#8 x 32 ThreadOur Small Stainless Steel Panel Studs have a wide range of uses. Originally they were used for mounting on the backside of dash panels for mounting to the console. Now they are used for securing a wide range of wire clamps and other small components to composite surfaces. The base plate is 0.62" in diameter with a 1.25" tall stud. Tensile strength is 300 lbs. and shear strength is 375 lbs. Maximum torque load is 45 inch/lbs.

Read more less

1" Tall Stainless Stud w/1/4" x 20 ThreadMounts to virtually any surface using the AT-4010 Acrylic Adhesive. This is a structural part with 500 lbs. of tensile strength and 650 lbs. in shear. All studs have 1/4" x 20 threads. Use for hanging panels, through deck mounts and many other uses.

Read more less

No Slide Metal/Composite BonderRevolutionary Metal Bonder will hold heavy parts at application without sliding either on a vertical or overhead surface. AT-8040 will hold 3,500lbs in 40 minutes. No Welding, Drilling or Tapping.Weld Mount AT-8040 is a solvent free, VOC Compliant, two part methacrylate-based, structural adhesive formulated to bond metals for use in severe environments. It will also bond engineered thermo- and thermosetting plastics, composites to metals or various substrate combinations. It has excellent adhesion to as received metal surfaces including aluminum, stainless steel, galvanized steel, and plated steels. AT-8040 forms a tough, high strength bonds usually with minimal surface preparation developing handling strength in 12 minutes and a functional cure within 45 minutes. Ultimate strength exceeds 3500 psi of tensile shear strength on aluminum with remarkable impact and peel strengths. AT-8040 will hold all Weld Mount parts on a vertical or overhead surface without sagging when properly used.Features: Revolutionary Adhesive Parts Stay Where Placed Without Sliding For Use Overhead and on Vertical Surfaces No Need for Fixtures Quick Guide (pdf)Owner's Manual (pdf)

Read more less

No Slide Metal/Composite Bonder *Case of 10*Revolutionary Metal Bonder will hold heavy parts at application without sliding on a vertical or overhead surface. AT-8040 will hold 3,500 lbs in 40 minutes - no Welding, Drilling, or Tapping.Weld Mount AT-8040 is a solvent-free, VOC Compliant, two-part methacrylate-based, structural adhesive formulated to bond metals for use in severe environments. It will also bond engineered thermo- and thermosetting plastics, and composites to metals or various substrate combinations. It has excellent adhesion to as-received metal surfaces including aluminum, stainless steel, galvanized steel, and plated steel. AT-8040 forms tough, high-strength bonds usually with minimal surface preparation developing handling strength in 12 minutes and a functional cure within 45 minutes. Ultimate strength exceeds 3500 psi of tensile shear strength on aluminum with remarkable impact and peel strengths. AT-8040 will hold all Weld Mount parts on a vertical or overhead surface without sagging when properly used.Features: Revolutionary Adhesive Parts Stay Where Placed Without Sliding For Use Overhead and on Vertical Surfaces No Need for Fixtures Case of 10 Quick Guide (pdf)Owner's Manual (pdf)

Read more less

Oetiker Stepless Clamp Kit with PliersStepless™ 150-Piece Clamp Rigging Kit by T-H Marine®. This product is made of high-quality materials to serve you for years to come. Designed using state-of-the-art technology and with customers in mind, this product by T-H Marine® will last a lifetime. Features: Plastic storage case contains 150 stainless steel Oetiker earless clamps, 10 each of 15 popular sizes, plus standard pincer installation tool Oetiker hose clamps with mechanical interlock allows use of pre-coated materials Specially formed strip edges reduce the risk of damage to the part being clamped with uniform compression and increased clamping force All 304 stainless steel bands - Kit includes full size range for all marine hose Includes: (10) 5.8-7MM Ear Clamps (10) 7.8 9.5MM Ear Clamps (10) 8.8-10.5MM Ear Clamps (10) 9.6-11.3MM Ear Clamps (10) 11.5-14MM Ear Clamps (10) 12-14.5MM Ear Clamps (10) 13.2-15.7MM Ear Clamps (10) 14.5-17MM Ear Clamps (10) 15.3-18.5MM Ear Clamps (10) 17.8-21MM Ear Clamps (10) 22.4-25.6 Ear Clamps (10) 26.9-30.1MM Ear Clamps (10) 28.4-31.6MM Ear Clamps (10) 37.8-41MM Ear Clamps (1) Oetiker Jaw Pliers (1) Plastic Tackle Tray

Read more less

AT-5 Large White Nylon Tie Mount - Qty. 500The AT-5 tie mount is designed to be set into wet resin during the hull lay up or bonded with our acrylic adhesives. It's designed for a #5 wire tie and has an average pull strength of 150 lbs. It's approved for submerged bilge applications. Stop putting plywood in your hull just to have a place to drive wire tie screws. Saves material and labor costs!

Read more less

White Nylon Wire Tie MountThe AT-3 tie mount is smaller for panel and other small space applications. This part is molded in white nylon and is sized for a #3 wire tie with a maximum width of .20". Average pull strength is about 50 lbs. The square base measures .44" wide. Use this smaller wire tie for runs with only a few wires or where space prevents use of our larger tie mounts. Excellent for mounting compass wires on center console boats and for overhead panel runs.

Read more less

White Nylon Wire Tie MountThe AT-5 tie mount is designed to be set into wet resin during the hull lay up or bonded with our acrylic adhesives. It's designed for a #5 wire tie and has an average pull strength of 150 lbs. It's approved for submerged bilge applications. Stop putting plywood in your hull just to have a place to drive wire tie screws. Saves material and labor costs!

Read more less

White Nylon Wire Tie MountThe AT-5 tie mount is designed to be set into wet resin during the hull lay up or bonded with our acrylic adhesives. It's designed for a #5 wire tie and has an average pull strength of 150 lbs. It's approved for submerged bilge applications. Stop putting plywood in your hull just to have a place to drive wire tie screws. Saves material and labor costs!

Read more less

AT-5B Large Black Nylon Wire Tie Mount - Qty. 500The AT-5 tie mount is designed to be set into wet resin during the hull lay up or bonded with our acrylic adhesives. It's designed for a #5 wire tie and has an average pull strength of 150 lbs. It's approved for submerged bilge applications. Stop putting plywood in your hull just to have a place to drive wire tie screws. Saves material and labor costs!

Read more less

1.5" Tall Stainless Stud w/#10 x 24 ThreadUtilize the same base as the 1.4" x 20 studs but with a smaller threaded stud inserted into the base. These studs are ideal for mounting wire clamps and securing items which require a smaller stud diameter. These studs can be bonded from either surface of the base plate.

Read more less

AT-651 Mixing Tips for Use with AT-6031 Adhesive - Qty. 10Weld Mount’s AT-651 mixing tip is designed specifically for use with Weld Mount’s AT-6031 adhesive. AT-6031 is a 10 to 1 adhesive that requires a mixing tip with more mixing chambers to ensure proper mixing before use. These mixing tips minimize waste compared with traditional 6" mixing tips. This package contains 10 mixing tips.Features:10 to 1 adhesive

Read more less

Aluminum Base Wire Tie MountThis tie mount is provided with an anodized aluminum base with a nylon tie mount which is riveted to the base. The nylon mount swivels 360 degrees making alignment with the wire harness easier. This tie mount is designed for a #5 wire tie and has an average pull strength of 150 lbs.

Read more less

Acrylic Adhesive - 10-PackCAN NOT SHIP AIR,UPS GROUND ONLYAT-4020 is a specially formulated adhesive for holding all our parts with little or no sagging in vertical or overhead applications. Cures in 10 - 12 minutes and has working strength within 40 minutes. AT-4020 is recommended for composite and plastic bonding applications and not for bonding to metal substrates. Unlike other 2 part acrylic adhesives AT-4020 has a one year shelf life when stored at 72 degrees but is best refrigerated when ever possible. It is packaged in a 50ml cartridge and can be mixed by hand or by using our AT-300 gun and mixing tips. The 50ml cartridge will bond 150 - 200 parts. Quick Guide (pdf)Owner's Manual (pdf)

Read more less

Footman's Strap MountThe Footman's Strap Mount is designed to be bonded with AT-4020 Acrylic Adhesive. This strap mount is 3.25" long and 1" wide and holds up to a 1.3" max strap width. This strap is incredibly strong, paintable, and is rated for over 600 lbs. strength. Use it for battery and tank tie downs and mounting heavy hoses and cables or deck mounted for life raft tie downs.

Read more less

Black Nylon Wire Tie MountThe AT-3 tie mount is smaller for panel and other small space applications. This part is molded in black nylon and is sized for a #3 wire tie with a maximum width of .20". Average pull strength is about 50 lbs. The square base measures .44" wide. Use this smaller wire tie for runs with only a few wires or where space prevents use of our larger tie mounts. Excellent for mounting compass wires on center console boats and for overhead panel runs.

Read more less

1.5" Tall Stainless Stud w/1/4" x 20 ThreadMounts to virtually any surface using the AT-4010 Acrylic Adhesive. This is a structural part with 500 lbs. of tensile strength and 650 lbs. in shear. All studs have 1/4" x 20 threads. Use for hanging panels, through deck mounts and many other uses.

Read more less

Black Nylon Wire Tie MountThe AT-5 tie mount is designed to be set into wet resin during the hull lay up or bonded with our acrylic adhesives. It's designed for a #5 wire tie and has an average pull strength of 150 lbs. It's approved for submerged bilge applications. Stop putting plywood in your hull just to have a place to drive wire tie screws. Saves material and labor costs!

Read more less

Footman's Strap MountThe Footman's Strap Mount is designed to be bonded with AT-4020 Acrylic Adhesive. This strap mount is 3.25" long and 1" wide and holds up to a 1.3" max strap width. This strap is incredibly strong, paintable, and is rated for over 600 lbs. strength. Use it for battery and tank tie downs and mounting heavy hoses and cables or deck mounted for life raft tie downs.

Read more less

AT-850 Square Mixing Tip f/2010, 4020, & 8040 Adhesives - 4" - Case of 10Weld Mount's AT-850 tip is for use only with the 2010, 4020, & 8040 adhesives. It's unique design eliminates any possibility of the cartridge plugging up as the entry is separated.Features: Square Mixing Tip 4" Long Case of 10

Read more less

Aluminum Wire TieUsed with Stainless Steel or Nylon wire ties up to 0.4 inches wide. 250 lbs tensile strength when bonded with AT-6030 adhesive manufactured of 5052 marine grade aluminum for UV and salt water resistance. Ideal alternative to welding or drilling and tapping to mount hoses, conduit, etc.

Read more less

AT-6031 Metal Bond AdhesiveAT-6031 is a 10-to-1 metal bonding adhesive. It has high viscosity (cures in 10–12 minutes), has a 6-minute working time, and develops working strength in 40 minutes. AT-6031 develops more than 2,500 lbs. (psi) of tensile strength on most metal surfaces, making it an ideal alternative to welding in many applications.The AT-6031 uses AT-651 mixing tips and comes in a 50mL cartridge. Compared to the previous version, users get 13mL more product at the same price.*AT-6031 has a 6-month shelf life and should always be stored refrigeratedFeatures:The nozzle on the cartridge will never freeze up

Read more less

AT-3B Small Black Nylon Wire Tie Mount - Qty. 500The AT-3 tie mount is smaller for panel and other small space applications. This part is molded in black nylon and is sized for a #3 wire tie with a maximum width of .20". Average pull strength is about 50 lbs. The square base measures .44" wide. Use this smaller wire tie for runs with only a few wires or where space prevents use of our larger tie mounts. Excellent for mounting compass wires on center console boats and for overhead panel runs.

Read more less

AT-850 Square Mixing Tip 4" - Case of 50Weld Mount's AT-850 tip is for use only with the 2010, 4010, & 8040 adhesives. It's unique design eliminates any possibility of the cartridge plugging up as the entry is separated.Features: Square Mixing Tip 4" Long Case of 50

Read more less

White Nylon Wire Tie MountThe AT-3 tie mount is smaller for panel and other small space applications. This part is molded in white nylon and is sized for a #3 wire tie with a maximum width of .20". Average pull strength is about 50 lbs. The square base measures .44" wide. Use this smaller wire tie for runs with only a few wires or where space prevents use of our larger tie mounts. Excellent for mounting compass wires on center console boats and for overhead panel runs.

Read more less

Black Nylon Wire Tie MountThe AT-5 tie mount is designed to be set into wet resin during the hull lay up or bonded with our acrylic adhesives. It's designed for a #5 wire tie and has an average pull strength of 150 lbs. It's approved for submerged bilge applications. Stop putting plywood in your hull just to have a place to drive wire tie screws. Saves material and labor costs!

Read more less

Acrylic Adhesive - 10-PackCAN NOT SHIP AIR,UPS GROUND ONLYAT-2010 is our biggest seller and is a unique adhesive. It has high viscosity and will hold smaller parts without sagging. AT-2010 cures in 5 - 6 minutes, has a 4 minute working time and develops working strength in 15 -20 minutes. This makes AT-2010 the ideal adhesive for applications which require an immediate high strength bond. AT-2010 has a 6 month shelf life when stored at 72 degrees. We recommend that where ever possible this adhesive be refrigerated. Packaged in a 50ml cartridge and can be mixed by hand or by using our AT-300 gun and mixing tips. The 50ml cartridge will bond 150 - 200 parts.

Read more less

Acrylic AdhesiveCAN NOT SHIP AIR,UPS GROUND ONLYAT-2010 is our biggest seller and is a unique adhesive. It has high viscosity and will hold smaller parts without sagging. AT-2010 cures in 5 - 6 minutes, has a 4 minute working time and develops working strength in 15 -20 minutes. This makes AT-2010 the ideal adhesive for applications which require an immediate high strength bond. AT-2010 has a 6 month shelf life when stored at 72 degrees. We recommend that where ever possible this adhesive be refrigerated. Packaged in a 50ml cartridge and can be mixed by hand or by using our AT-300 gun and mixing tips. The 50ml cartridge will bond 150 - 200 parts.** AT 850 Mixing Tips sku 56273 required ** Brochure (pdf)

Read more less

Marine Formula™ 10oz AerosolMarine Formula™ is a specially formulated patented mixture that cleans and removes adhesives and sealants on and inside the boat. Use Marine Formula™ to clean up and remove these common marine adhesives and sealants. Quick Guide (pdf)

Read more less

Acrylic AdhesiveCAN NOT SHIP AIR,UPS GROUND ONLYAT-4020 is a specially formulated adhesive for holding all our parts with little or no sagging in vertical or overhead applications. Cures in 10 - 12 minutes and has working strength within 40 minutes. AT-4020 is recommended for composite and plastic bonding applications and not for bonding to metal substrates. Unlike other 2 part acrylic adhesives AT-4020 has a one year shelf life when stored at 72 degrees but is best refrigerated when ever possible. It is packaged in a 50ml cartridge and can be mixed by hand or by using our AT-300 gun and mixing tips. The 50ml cartridge will bond 150 - 200 parts. Brochure (pdf)

Read more less

Marine Formula™ 5oz AerosolMarine Formula™ is a specially formulated patented mixture that cleans and removes adhesives and sealants on and inside the boat. Use Marine Formula™ to clean up and remove these common marine adhesives and sealants. Quick Guide (pdf)

Read more less

Prop Master Propeller WrenchThe Prop Master™ is the original molded propeller wrench.This 1-1/16" six point socket style prop wrench is made of high tensile strength, indestructible nylon. It is totally resistant to fuel, sun, salt water, and other chemicals. The Prop Master™ is less expensive than metal wrenches which rattle and can cause damage to your boat. However, it has plenty of brawn to get the job done. The Prop Master™ will tighten all 1 1/16" propeller nuts without slipping or stripping. (OMC, Johnson and Evinrude, - over 40 HP, Mercury - over 50 HP) High visibility color makes it easy to locate in dark boat compartments. The Prop Master™ also has a 9/16" garboard drain plug socket on the reverse side. Will not corrode in the salt water environment.Features: Fits All 1-1/16” Prop Nuts (40hp & up) Rugged Nylon Resists Stripping 9/16” Garboard Drain Socket on Back Non-Corrosive in Salt Environment High Visibility Yellow makes wrench easy to find WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Pitch: N/A Material: Polymer Diameter (Inches): 0.6875 Box Dimensions: 2"H x 6"W x 16"L WT: 0.6 lbs UPC: 733572020007

Read more less

Add-A-Snap - White - 2-1/2" For use with canvas or nylon boat covers, the Add-A-Snap allows you to easily add length on hard to reach snaps from shrunken material. Nickel plated brass/nylon.WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less

Add-A-Snap - Black - 4" For use with canvas or nylon boat covers, the Add-A-Snap allows you to easily add length on hard to reach snaps from shrunken material. Nickel plated brass/nylon.WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less

Add-A-Snap - White - 4" For use with canvas or nylon boat covers, the Add-A-Snap allows you to easily add length on hard to reach snaps from shrunken material. Nickel plated brass/nylon.WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less

Canvas Snap Tool Canvas Snap Tool includes a die wrench and three removable dies for various snap caps and studs. Great addition to any tool box. Aluminum/steel construction. Not for use with heavy duty stainless canvas snaps. WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less

NAVDoctor NMEA Network Diagnostic ToolNAVDoctor is the perfect NMEA 2000 diagnostic tool for dealers, installers, and boat builders. It turns any mobile device into an NMEA 2000 network analyzer, creating simple and clear web pages that show the health and status of your NMEA 2000 network. NAVDoctor is a portable NMEA 2000 network diagnostic tool/tester. It allows you to quickly check and diagnose the NMEA 2000 network. It combines the functionality of existing NMEA 2000 display programs and test equipment into a single, cost-effective, simple plug ‘n play box.It’s self-powered from the network and creates a local wifi point for a mobile phone, tablet, or PC to connect.  Once connected, you simply access functions through a web browser so there’s no complicated software to install.NMEA 2000 networks are based on a robust Canbus architecture, but one bad device, cable, or termination can have a detrimental effect on performance.  Fault finding can be time-consuming and tricky, so having a NAVDoctor in your toolkit will save you time, money, and frustration.NAVDoctor is an essential tool for every marine electronics technician or installer and also offers the capability of printing a network health check certificate to validate an installation and improve customer service.OperationYou can configure the NavDoctor through its simple web interface, just open your web browser, enter the NavDoctor’s IP address and you can access the NavDoctor web interface. So no complicated programming software or app is required.Through the web interface, you can analyze all the equipment connected to the NMEA 2000 network and get additional information about the equipment. You can also display all the NMEA 2000 data (PGN) being received.The health section gives you an overview of the NMEA 2000 network (voltage, bus capacity, etc.). Finally, the test report section analyses all the NMEA 2000 network, equipment, and data and can generate a PDF.Features: NMEA 2000 Wireless Diagnostic Tool Self-powered from NMEA 2000 bus – fits in seconds Creates its wireless network on the boat or can join an existing network in the workshop No apps are required, NAVDoctor’s simple web interface displays in your browser Lists all devices on the NMEA network and all PGNs being transmitted The health page gives you an immediate snapshot of the network key performance parameters Can log all data to text file for in-depth analysis Generates a Network Health Report that you can either print or save to PDF You can give a health report to the customer or you can retain it for your installation records Specifications:Dimensions: 180mm x 145mm x 40mmWhat's In The Box? 1M NMEA2000 drop cable WiFi antenna built-in Owner's Manual (pdf)

Read more less

Emergency Deck Fill PlugNitrile-Buna RubberThis Emergency Deck Fill Plug is a must for any vessel. Fits most 1-1/2" hose deck fills in the event you lose your cap. For temporary use only until you can replace your OEM cap. Constructed of fuel resistant Nitrile-Buna rubber. WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less

Stainless Steel Bottle Opener with Brushed Finish Corrosion resistant investment cast 316 stainless steel bottle opener wall mounts with two #6 FH fasteners (not included).WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less