![NavPod SailPod Pre-Cut f/Garmin 1242xsv, 1222xsv 1222 f/9.5" Wide Guard [GP1200-13]](http://rebellionmarine.com/cdn/shop/files/69552XL.jpg?crop=center&height=645&v=1740086666&width=645)
-
![NavPod SailPod Pre-Cut f/Garmin 1242xsv, 1222xsv 1222 f/9.5" Wide Guard [GP1200-13]](//rebellionmarine.com/cdn/shop/files/69552XL.jpg?crop=center&height=645&v=1740086666&width=645)
NavPod NavPod SailPod Pre-Cut f/Garmin 1242xsv, 1222xsv 1222 f/9.5" Wide Guard [GP1200-13]
SailPod Pre-Cut for Garmin 1242xsv, 1222xsv & 1222 for 9.5" Wide GuardSailPods are for mounting a single Radar or Chartplotter at the helm. Navigation at your finger tips. “Where you need it…when you need it”. Sail Pods are the smart solution for mounting your Radar or Chartplotter at the helm where you can easily operate and clearly see the fine details of the screen. NavPods have a high gloss finish, giving you a clean mounting solution while concealing unsightly wires. Nickel Chrome plated tamperproof screws provide a little bling and a lot of security. Designed with a double gasket waterproof seal, NavPods protect your electronics from the harshest of wet offshore boating conditions. A SailPod is best mounted on a Single Bend AngleGuard or use a Double Bend AngleGuard to fit an InstrumentPod on the top vertical section and SailPod below on the angled section.Structural Rigidity – The Gen3 enhancements now include a thicker gauge acrylic capped ABS material that improves strength and provides better structural rigidity. This thicker material allows for a larger waterproof seal. The better the structural rigidity, the less flexing when tightening and more uniform pressure on the seal. The excellent UV stability of the acrylic is combined with the durability of the ABS. The acrylic cap protects the ABS from UV and its potentially damaging effects on plastic.Waterproof Seal – All SailPods are manufactured with a double gasket system providing an excellent watertight seal. This seal provides the best protection of your Marine Electronics. SailPods are made to withstand the harshest wet offshore boating conditions. Gen3 enhancements include a thicker external silicone gasket with improved flush fit. The internal Poran Microcell Polyurathane gasket is now 50% thicker and is not subject to “compression set” like many rubber compounds. This is important when you need to open the SailPod in the future in order to service your electronics. The gasket will continue to do its job.Nickel Chrome Plated Stainless Steel – We use all 316 stainless steel hardware that is supplied with each NavPod. Large round head tamperproof screws have deeper sockets for the NavPod wrench for better holding ability when tightening than screws used on our Traditional Series NavPod. For Gen3 NavPods we provide nickel chrome-plated stainless steel tamperproof screws for security combined with a little style!Commitment to Quality - We stand behind our commitment by offering a 10-year warranty on all new Gen3 NavPods.This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns. Specifications: Cut/Uncut: Cut Mounting Style: Pedestal Box Dimensions: 8"H x 11"W x 17"L WT: 7.5 lbs UPC: 659988113778
$499.99 $427.99
-
Navpod NavPod StarPod 3 System For Starlink Gen 3 Standard
NavPod SPS3000 StarPod 3 System for Starlink Gen3 Standard Dish (23.04 x 15.07? dish size)Model: SPS3000The StarPod 3 System is a waterproof, secure, attractive mounting solution for your Starlink Gen3 Standard antenna. The housing features a built-in 10-degree angle and full swivel adjustability so that the dish can be manually adjusted for an optimized view of Starlink satellites in the sky. The 10-degree angle also prevents water from pooling on top of the housing, which can cause signal interference.***NOTE*** Assembly of this product requires the use of a deck fill wrench (Groco model SW-2531 or equivalent product). This tool is NOT included with the StarPod.Third-Party Accessory Disclaimer: The NavPod and StarPod brands are in no way affiliated with the Starlink or SpaceX brands. Their products are third-party accessories, distinct from the brands and products they are designed to house.Liability Disclaimer: NavPod assumes no liability for any violation of Starlink product warranty or terms of service that may result from modifying a Starlink dish or mounting it inside a StarPod
$700.79
-
Navpod NavPod StarPod 2 System For Starlink Gen 2 Actuated
NavPod SPS2000 StarPod 2 System for Starlink Actuated (Starlink Gen2 Actuated dish; 20.2 x 11.9? dish size)Model: SPS2000The StarPod 2 System is a waterproof, secure, attractive mounting solution for your Starlink Gen2 Actuated antenna. The housing features a built-in 10-degree angle and full swivel adjustability so that the dish can be manually adjusted for an optimized view of Starlink satellites in the sky. The 10-degree angle also prevents water from pooling on top of the housing, which can cause signal interference.***NOTE*** Assembly of this product requires the use of a deck fill wrench (Groco model SW-2531 or equivalent product). This tool is NOT included with the StarPod.Third-Party Accessory Disclaimer: The NavPod and StarPod brands are in no way affiliated with the Starlink or SpaceX brands. Their products are third-party accessories, distinct from the brands and products they are designed to house.Liability Disclaimer: NavPod assumes no liability for any violation of Starlink product warranty or terms of service that may result from modifying a Starlink dish or mounting it inside a StarPod
$700.79
-
Navpod NAVPOD GP2200-20 SailPod 1223/1243/xsv 12" Wide Guard
NavPod GP2200-20 SailPod Pre-Cut for Garmin GPSMAP 1223/1223xsv/1243/1243xsv/1253xsv for 12? wide guardModel: GP2200-20SailPods are for mounting a single Radar or Chartplotter at the helm. Navigation at your finger tips? "Where you need it, when you need it." SailPods are the smart solution for mounting your Radar or Chartplotter at the helm where you can easily operate and clearly see the fine details of the screen. NavPods have a high gloss finish, giving you a clean mounting solution while concealing unsightly wires. Nickel Chrome-Plated tamper-resistant screws provide a little bling and a lot of security. Designed with a double gasket waterproof seal, NavPods protect your electronics from the harshest of wet offshore boating conditions. A SailPod is best mounted on a Single Bend AngleGuard, or on the angled section of a Double Bend Angle Guard with an InstrumentPod mounted above it on the straight section.Structural Rigidity — The Gen3 enhancements now include a thicker gauge acrylic capped ABS material that improves strength and provides better structural rigidity. This thicker material allows for a larger waterproof seal. The better the structural rigidity, the less flexing when tightening and more uniform pressure on the seal. The excellent UV stability of the acrylic is combined with the durability of the ABS. The acrylic cap protects the ABS from UV and its potentially damaging effects on plastic.Waterproof Seal — All SailPods are manufactured with a double gasket system providing an excellent watertight seal. This seal provides the best protection of your Marine Electronics. SailPods are made to withstand the harshest wet offshore boating conditions. Gen3 enhancements include a thicker external silicone gasket with improved flush fit. The internal Poron Microcell Polyurethane gasket is now 50% thicker and is not subject to "compression set" like many rubber compounds. This is important when you need to open the SailPod in the future in order to service your electronics. The gasket will continue to do its job.Nickel Chrome-Plated Stainless Steel — We use all 316 stainless steel hardware that is supplied with each NavPod. Large round-head tamper-resistant screws have deeper sockets for the NavPod wrench for better holding ability when tightening than screws used on our Traditional Series NavPod. The Nickel Chrome-Plated Stainless Steel tamper-resistant screws provide security combined with a little style!Commitment to Quality — We stand behind our commitment by offering a 10-year warranty on all new Gen3 NavPods.
$437.99
-
Navpod Navpod SK135 Stanchion Kit for dash mounting of GP1800 GP1040, GP1050, GP1200
NAVPOD SK135 PowerPanel Stanchion KitModel: SK135Stanchion Kit Pre-drilled for GP1050, GP1200, GP1030, GP1060, GP1800 Series SailPods, GP1040, GP1080, GP1170 Series SystemPodsThe SK135 Stanchion Kit can be combined with most SystemPods (or SailPods) for a very strong and sturdy mounting system. The system includes two 1.25" diameter mirror polished 316 grade stainless steel tubes with 0.065" wall thickness, 15" tall with a 20° bend, pre-drilled to easily fit together with a compatible NavPod. Wires can be routed down both tubes and are all concealed for a very clean installation. Includes pair of round stainless steel feet and mounting hardware.Great for on dash mounting on Powerboats or extending the available dash space on the flybridge. Useful for unique mounting locations in the cockpit on Sailboats. Can be used for overhead mounting as well (however, check out the SK125, SK129, and SK130 Stanchion Kits first, as those models are designed specifically for overhead applications).Compatible NavPods are the GP1030, GP1050, GP1060, GP1080, GP1170, GP1200, GP1800, GP1900, GP1920, GP2030, GP2060, GP2080, GP2170, GP2200, and GP2920 Series.
$218.99
-
Navpod NAVPOD SK130 PowerPanel Stanch for overhead mounting GP1030, GP1060
NAVPOD SK130 PowerPanel Stanchion KitModel: SK130PowerPanel Stanchion Kit -Two 1.25" S.S. tubes for overhead mounting of GP1030, GP1060, GP1080 or GP1170 Serieshe SK130 Large PowerPanel Stanchion Kit is used for overhead mounting of the GP1030, GP1060 Series SailPods & GP1080, GP1170 Series SystemPods.PowerPanel Stanchion Kits are a very strong, sturdy, and secure way to mount electronics in the overhead area where an overhead box does not exist. The NavPod will be positioned at 40 degrees off the vertical axis. The stanchion tubes are made from mirror polished 316 grade stainless steel with 1.25" tube diameter and 0.065" wall thickness. There are 3 different Stanchion Kits for different size NavPods. Find the right SystemPod or SailPod for your electronics, then choose the corresponding Stanchion Kit. Each kit includes stainless steel feet and mounting hardware.
$218.99
-
Navpod NAVPOD SK129 PowerPanel Stanch for overhead mounting GP1800, GP1040,
NAVPOD SK129 PowerPanel Stanchion KitModel: SK129PowerPanel Stanchion Kit -Two 1.25" S.S. tubes for overhead mounting of GP1800, GP1040, GP1050 or GP1200 SeriesThe SK129 Medium PowerPanel Stanchion Kit is used for overhead mounting of the GP1050, GP1200, GP1800, GP1900 Series SailPods & GP1040 SystemPod.PowerPanel Stanchion Kits are a very strong, sturdy, and secure way to mount electronics in the overhead area where an overhead box does not exist. The NavPod will be positioned at 40 degrees off the vertical axis. The stanchion tubes are made from mirror polished 316 grade stainless steel with 1.25" tube diameter and 0.065" wall thickness. There are 3 different Stanchion Kits for different size NavPods. Find the right SystemPod or SailPod for your electronics, then choose the corresponding Stanchion Kit. Each kit includes stainless steel feet and mounting hardware.
$218.99
-
Navpod NAVPOD SK125 PowerPanel Stanch for overhead mounting of GP1300, GP1400, GP1500,
NAVPOD SK125 PowerPanel Stanchion KitModel: SK125PowerPanel Stanchion Kit -Two 1.25" S.S. tubes for overhead mounting of GP1300, GP1400, GP1500 or GP1600 SeriesThe SK125 Small PowerPanel Stanchion Kit is used for overhead mounting of the GP1300, GP1400 Series InstrumentPods and the GP1500, GP1600 Series SystemPods.PowerPanel Stanchion Kits are a very strong, sturdy, and secure way to mount electronics in the overhead area where an overhead box does not exist. The NavPod will be positioned at 40 degrees off the vertical axis. The stanchion tubes are made from mirror polished 316 grade stainless steel with 1.25" tube diameter and 0.065" wall thickness. There are 3 different Stanchion Kits for different size NavPods. Find the right SystemPod or SailPod for your electronics, then choose the corresponding Stanchion Kit. Each kit includes stainless steel feet and mounting hardware.
$218.99
-
Navpod NAVPOD SK11 Stanchion Kit for mounting GP1300, GP1400 GP1500, GP1600
NAVPOD SK11 Stanchion KitModel: SK11Stanchion Kit predrilled for GP1300, GP1400 Series InstrumentPods, GP1500, GP1600 and GP1040 Series SystemPods and GP1800 Series SailPodsThe SK11 Stanchion Kit is a very strong and sturdy mounting system used for mounting GP1300, GP1400 Series InstrumentPods, GP1500, GP1600 and GP1040 Series SystemPods and GP1800, GP1900 Series SailPods. The stanchion tubes are made from mirror polished 316 grade stainless steel with 1.25" tube diameter and 0.065" wall thickness, 11" high and pre-drilled to easily fit together with a compatible NavPod. Wires can be routed down both tubes and are all concealed for a very clean installation. Includes pair of round stainless steel feet and mounting hardware.Great for on dash mounting on Powerboats or extending the available dash space on the flybridge. Useful for unique mounting locations in the cockpit on Sailboats. Can be used for overhead mounting as well (however, check out the SK125, SK129, and SK130 Stanchion Kits first, as those models are designed specifically for overhead applications).
$175.19
-
Navpod Navpod SK100 Stanchion Kit
NavPod SK100 Stantion Kit SK100 Stanchion Kitis used for mounting all 9.5" InstrumentPods or GP160 Series SystemPods onto a flat surface. H W Overall Size 15" 9.5" Stanchion Kit includes 1" diameter 316 stainless steel Mirror polished finish Pre-drilled mounting and wire access hole Stainless steel feet can be removed for adjusting the height
$87.59
-
Navpod Navpod SG225 Straight Guard 12" Wide 1.25" Tube
NAVPOD SG225 StraightGuardModel: SG225 316 grade stainless steel 065 gauge wall thickness Mirror polished finish All 1.25" include stainless steel feet (1" does not include feet) StraightGuard 12" Wide 1.25" Straight for InstrumentPodsSG10 StraightGuard has no bends and is designed to fit a single InstrumentPod. 1" diameter stainless steel tubes. No feet included on 1" StraightGuards.
$385.42
-
Navpod Navpod SG125 Straight Guard 1.25" Stainless Steel Tube
"Navpod SG125 Straight Guard 1.25" Stainless Steel TubeModel: SG125Navpod SG125 Straight Guard 1.25" Stainless Steel TubeSpecifications Part Number NAVSG125 Freight Program Qualifies for Ground Program Vendor Item Number SG125 Brand Navpod UPC 659988103373
$385.42
-
Navpod Navpod SG10 Straight Guard 1" Stainless Steel Tube
NAVPOD SG10 StraightGuardModel: SG10 316 grade stainless steel 065 gauge wall thickness Mirror polished finish All 1.25" include stainless steel feet (1" does not include feet) StraightGuard 9.5" Wide 1" Straight for InstrumentPodsSG10 StraightGuard has no bends and is designed to fit a single InstrumentPod. 1" diameter stainless steel tubes. No feet included on 1" StraightGuards.Height in 2.75 cm 7.0 Width in 6.98 cm 17.7 View Angle 30
$332.88
-
Navpod NAVPOD RMX4900-14 Railmount for Humminbird SOLIX 10
NAVPOD RMX4900-14 RailmountModel: RMX4900-14RailMount Pre-Cut for Humminbird SOLIX 10 (fits 1" or 1.25" tubing)RailMount NavPods are best used for mounting of an autopilot control, sailing instrument, or small chartplotter onto an existing pedestal guard. Fits onto any 1" or 1.25" diameter tube. A Nickel Chrome-Plated Stainless Steel arm is used to mount a NavPod. The NavPod can rotate 180 degrees for easy viewing while sitting under the dodger on a rainy day. All wiring runs from the NavPod, down the center of the stainless steel arm, and into the pedestal guard. This application provides a clean and sturdy installation for electronics, without replacement of the pedestal guard.RailMounts are designed for all popular standard size instruments as well as 7 and 9 inch chartplotters.Structural Rigidity — The Gen3 enhancements now include a thicker gauge acrylic capped ABS material that improves strength and provides better structural rigidity. This thicker material allows for a larger waterproof seal. The better the structural rigidity, the less flexing when tightening and more uniform pressure on the seal. The excellent UV stability of the acrylic is combined with the durability of the ABS. The acrylic cap protects the ABS from UV and its potentially damaging effects on plastic.Waterproof Seal — All RailMount NavPods are manufactured with a double gasket system providing an excellent watertight seal. This seal provides the best protection of your Marine Electronics. NavPods are made to withstand the harshest wet offshore boating conditions. Gen3 enhancements include a thicker external silicone gasket with improved flush fit. The internal Poron Microcell Polyurethane gasket is now 50% thicker and is not subject to "compression set" like many rubber compounds. This is important when you need to open the NavPod in the future in order to service your electronics. The gasket will continue to do its job.Nickel Chrome-Plated Stainless Steel — We use all 316 stainless steel hardware that is supplied with each NavPod. Large round-head tamper-resistant screws have deeper sockets for the NavPod wrench for better holding ability when tightening than screws used on our Traditional Series NavPod. The Nickel Chrome-Plated Stainless Steel tamper-resistant screws provide security combined with a little style!Specifications Overall Height in 11.61 cm 29.5 Width in 14.25 Width 36.2 Depth in 7.72 cm 19.6 Usable Face Height 7.39 in 7.39 cm 18.8 Width in 12.36 cm 31.4 Depth in 5.29 cm 13.4 Max Cutout Height in 8.09 cm 20.5 Width in 13.26 cm 33.7 RMX Radius Height in 2.75 cm 7.0 Width in 6.98 cm 17.7 View Angle 30
$525.59
-
Navpod NAVPOD RMX4900-11 Railmount for Garmin GPSMAP 1042/1022
NAVPOD RMX4900-11 RailmountModel: RMX4900-11RailMount NavPod for Garmin GPSMAP 1042xsv/1022xsv/1022 (fits 1" or 1.25" tubing)RailMount NavPods are best used for mounting of an autopilot control, sailing instrument, or small chartplotter onto an existing pedestal guard. Fits onto any 1" or 1.25" diameter tube. A Nickel Chrome-Plated Stainless Steel arm is used to mount a NavPod. The NavPod can rotate 180 degrees for easy viewing while sitting under the dodger on a rainy day. All wiring runs from the NavPod, down the center of the stainless steel arm, and into the pedestal guard. This application provides a clean and sturdy installation for electronics, without replacement of the pedestal guard.RailMounts are designed for all popular standard size instruments as well as 7 and 9 inch chartplotters.Structural Rigidity — The Gen3 enhancements now include a thicker gauge acrylic capped ABS material that improves strength and provides better structural rigidity. This thicker material allows for a larger waterproof seal. The better the structural rigidity, the less flexing when tightening and more uniform pressure on the seal. The excellent UV stability of the acrylic is combined with the durability of the ABS. The acrylic cap protects the ABS from UV and its potentially damaging effects on plastic.Waterproof Seal — All RailMount NavPods are manufactured with a double gasket system providing an excellent watertight seal. This seal provides the best protection of your Marine Electronics. NavPods are made to withstand the harshest wet offshore boating conditions. Gen3 enhancements include a thicker external silicone gasket with improved flush fit. The internal Poron Microcell Polyurethane gasket is now 50% thicker and is not subject to "compression set" like many rubber compounds. This is important when you need to open the NavPod in the future in order to service your electronics. The gasket will continue to do its job.Nickel Chrome-Plated Stainless Steel — We use all 316 stainless steel hardware that is supplied with each NavPod. Large round-head tamper-resistant screws have deeper sockets for the NavPod wrench for better holding ability when tightening than screws used on our Traditional Series NavPod. The Nickel Chrome-Plated Stainless Steel tamper-resistant screws provide security combined with a little style!Specifications Overall Height in 11.61 cm 29.5 Width in 14.25 Width 36.2 Depth in 7.72 cm 19.6 Usable Face Height 7.39 in 7.39 cm 18.8 Width in 12.36 cm 31.4 Depth in 5.29 cm 13.4 Max Cutout Height in 8.09 cm 20.5 Width in 13.26 cm 33.7 RMX Radius Height in 2.75 cm 7.0 Width in 6.98 cm 17.7 View Angle 30
$525.59
-
Navpod NAVPOD RMX4900-01 Railmount for Raymarine eS95/97/98
NAVPOD RMX4900-01 RailmountModel: RMX4900-01RailMount Pre-Cut for Raymarine eS95/eS97/eS98 & AXIOM PRO 9 (fits 1" or 1.25" tubing)RailMount NavPods are best used for mounting of an autopilot control, sailing instrument, or small chartplotter onto an existing pedestal guard. Fits onto any 1" or 1.25" diameter tube. A Nickel Chrome-Plated Stainless Steel arm is used to mount a NavPod. The NavPod can rotate 180 degrees for easy viewing while sitting under the dodger on a rainy day. All wiring runs from the NavPod, down the center of the stainless steel arm, and into the pedestal guard. This application provides a clean and sturdy installation for electronics, without replacement of the pedestal guard.RailMounts are designed for all popular standard size instruments as well as 7 and 9 inch chartplotters.Structural Rigidity — The Gen3 enhancements now include a thicker gauge acrylic capped ABS material that improves strength and provides better structural rigidity. This thicker material allows for a larger waterproof seal. The better the structural rigidity, the less flexing when tightening and more uniform pressure on the seal. The excellent UV stability of the acrylic is combined with the durability of the ABS. The acrylic cap protects the ABS from UV and its potentially damaging effects on plastic.Waterproof Seal — All RailMount NavPods are manufactured with a double gasket system providing an excellent watertight seal. This seal provides the best protection of your Marine Electronics. NavPods are made to withstand the harshest wet offshore boating conditions. Gen3 enhancements include a thicker external silicone gasket with improved flush fit. The internal Poron Microcell Polyurethane gasket is now 50% thicker and is not subject to "compression set" like many rubber compounds. This is important when you need to open the NavPod in the future in order to service your electronics. The gasket will continue to do its job.Nickel Chrome-Plated Stainless Steel — We use all 316 stainless steel hardware that is supplied with each NavPod. Large round-head tamper-resistant screws have deeper sockets for the NavPod wrench for better holding ability when tightening than screws used on our Traditional Series NavPod. The Nickel Chrome-Plated Stainless Steel tamper-resistant screws provide security combined with a little style!Specifications Overall Height in 11.61 cm 29.5 Width in 14.25 Width 36.2 Depth in 7.72 cm 19.6 Usable Face Height 7.39 in 7.39 cm 18.8 Width in 12.36 cm 31.4 Depth in 5.29 cm 13.4 Max Cutout Height in 8.09 cm 20.5 Width in 13.26 cm 33.7 RMX Radius Height in 2.75 cm 7.0 Width in 6.98 cm 17.7 View Angle 30
$525.59
-
Navpod Navpod RMX4809 Railmount Pod PRE-CUT Raymarine A95/97/98
NavPod RMX4814 RailMount NavPod Pre-Cut for Raymarine a95/a97/a98 RailMount NavPods are best used for mounting of an autopilot control, sailing instrument, or small chartplotter onto an existing pedestal guard. Fits onto any 1" or 1.25" diameter tube. A Chromed Stainless Steel arm is used to mount a NavPod. The NavPod can rotate 180 degrees for easy viewing while sitting under the dodger on a rainy day. All wire run from the NavPod, down the center of the stainless steel arm, and into the pedestal guard. This application provides a clean and sturdy installation for electronics, without replacement of the pedestal guard. H W D Overall Size 9" 10.2" 6" Usable Face 5.6" 8.9" 3.75" Max Cutout 4.625" 8" All RailMount NavPods include Acrylic capped ABS plastic Chromed stainless steel tamper-proof fasteners Double Seal for watertight integrity Models are available pre-cut for popular electronics. Chromed stainless steel arm with swivel mount Both sets of adaptors included for 1" or 1.25" diameter tubing
$525.59
-
Navpod Navpod RMX4813 Railmount Pod PRE-CUT Simrad NSS9 evo2
NavPod RMX4813 RailMount Pre-Cut for Simrad NSS9 evo2 or B&G Zeus2 9" RailMount NavPods are best used for mounting of an autopilot control, sailing instrument, or small chartplotter onto an existing pedestal guard. Fits onto any 1" or 1.25" diameter tube. A Chromed Stainless Steel arm is used to mount a NavPod. The NavPod can rotate 180 degrees for easy viewing while sitting under the dodger on a rainy day. All wire run from the NavPod, down the center of the stainless steel arm, and into the pedestal guard. This application provides a clean and sturdy installation for electronics, without replacement of the pedestal guard. H W D Overall Size 9" 10.2" 6" Usable Face 5.6" 8.9" 3.75" Max Cutout 4.625" 8" All RailMount NavPods include Acrylic capped ABS plastic Chromed stainless steel tamper-proof fasteners Double Seal for watertight integrity Models are available pre-cut for popular electronics. Chromed stainless steel arm with swivel mount Both sets of adaptors included for 1" or 1.25" diameter tubing
$525.59
-
Navpod Navpod RMX4811 Railmount Pod PRE-CUT Garmin 8000/8208
NavPod RMX4811 RailMount NavPod Pre-Cut for Garmin 8008/8208 RailMount NavPods are best used for mounting of an autopilot control, sailing instrument, or small chartplotter onto an existing pedestal guard. Fits onto any 1" or 1.25" diameter tube. A Chromed Stainless Steel arm is used to mount a NavPod. The NavPod can rotate 180 degrees for easy viewing while sitting under the dodger on a rainy day. All wire run from the NavPod, down the center of the stainless steel arm, and into the pedestal guard. This application provides a clean and sturdy installation for electronics, without replacement of the pedestal guard. H W D Overall Size 9" 10.2" 6" Usable Face 5.6" 8.9" 3.75" Max Cutout 4.625" 8" All RailMount NavPods include Acrylic capped ABS plastic Chromed stainless steel tamper-proof fasteners Double Seal for watertight integrity Models are available pre-cut for popular electronics. Chromed stainless steel arm with swivel mount Both sets of adaptors included for 1" or 1.25" diameter tubing
$525.59
-
Navpod Navpod RMX4809 Railmount Pod PRE-CUT Raymarine C/E 95/97
NavPod RMX4809 RailMount NavPod Pre-Cut for Raymarine c95 / c97 / e95 / e97 RailMount NavPods are best used for mounting of an autopilot control, sailing instrument, or small chartplotter onto an existing pedestal guard. Fits onto any 1" or 1.25" diameter tube. A Chromed Stainless Steel arm is used to mount a NavPod. The NavPod can rotate 180 degrees for easy viewing while sitting under the dodger on a rainy day. All wire run from the NavPod, down the center of the stainless steel arm, and into the pedestal guard. This application provides a clean and sturdy installation for electronics, without replacement of the pedestal guard. H W D Overall Size 9" 10.2" 6" Usable Face 5.6" 8.9" 3.75" Max Cutout 4.625" 8" All RailMount NavPods include Acrylic capped ABS plastic Chromed stainless steel tamper-proof fasteners Double Seal for watertight integrity Models are available pre-cut for popular electronics. Chromed stainless steel arm with swivel mount Both sets of adaptors included for 1" or 1.25" diameter tubing
$525.59
-
Navpod Navpod RMX4808 Railmount Pod PRE-CUT Simrad NSS8
NavPod RMX4808 RailMount NavPod Pre-Cut for B&G Zeus Touch 8 and Simrad NSS 8 RailMount NavPods are best used for mounting of an autopilot control, sailing instrument, or small chartplotter onto an existing pedestal guard. Fits onto any 1" or 1.25" diameter tube. A Chromed Stainless Steel arm is used to mount a NavPod. The NavPod can rotate 180 degrees for easy viewing while sitting under the dodger on a rainy day. All wire run from the NavPod, down the center of the stainless steel arm, and into the pedestal guard. This application provides a clean and sturdy installation for electronics, without replacement of the pedestal guard. H W D Overall Size 9" 10.2" 6" Usable Face 5.6" 8.9" 3.75" Max Cutout 4.625" 8" All RailMount NavPods include Acrylic capped ABS plastic Chromed stainless steel tamper-proof fasteners Double Seal for watertight integrity Models are available pre-cut for popular electronics. Chromed stainless steel arm with swivel mount Both sets of adaptors included for 1"or 1.25" diameter tubing
$525.59
-
Navpod Navpod RMX4804 Railmount Pod PRE-CUT Garmin 5008/5208
NavPod RMX4804 RailMount NavPod Pre-Cut for Garmin 5008 / 5208 RailMount NavPods are best used for mounting of an autopilot control, sailing instrument, or small chartplotter onto an existing pedestal guard. Fits onto any 1" or 1.25" diameter tube. A Chromed Stainless Steel arm is used to mount a NavPod. The NavPod can rotate 180 degrees for easy viewing while sitting under the dodger on a rainy day. All wire run from the NavPod, down the center of the stainless steel arm, and into the pedestal guard. This application provides a clean and sturdy installation for electronics, without replacement of the pedestal guard. H W D Overall Size 9" 10.2" 6" Usable Face 5.6" 8.9" 3.75" Max Cutout 4.625" 8" All RailMount NavPods include Acrylic capped ABS plastic Chromed stainless steel tamper-proof fasteners Double Seal for watertight integrity Models are available pre-cut for popular electronics. Chromed stainless steel arm with swivel mount Both sets of adaptors included for 1" or 1.25" diameter tubing
$525.59
-
Navpod NAVPOD RMX4800-20 Railmount for Garmin 7408/7608
NAVPOD RMX4800-20 RailmountModel: RMX4800-20RailMount Pre-Cut for Garmin GPSMAP 7408/7408xsv/7608/7608xsvRailMount NavPods are best used for mounting of an autopilot control, sailing instrument, or small chartplotter onto an existing pedestal guard. Fits onto any 1" or 1.25" diameter tube. A Nickel Chrome-Plated Stainless Steel arm is used to mount a NavPod. The NavPod can rotate 180 degrees for easy viewing while sitting under the dodger on a rainy day. All wiring runs from the NavPod, down the center of the stainless steel arm, and into the pedestal guard. This application provides a clean and sturdy installation for electronics, without replacement of the pedestal guard.RailMounts are designed for all popular standard size instruments as well as 7 and 9 inch chartplotters.Structural Rigidity — The Gen3 enhancements now include a thicker gauge acrylic capped ABS material that improves strength and provides better structural rigidity. This thicker material allows for a larger waterproof seal. The better the structural rigidity, the less flexing when tightening and more uniform pressure on the seal. The excellent UV stability of the acrylic is combined with the durability of the ABS. The acrylic cap protects the ABS from UV and its potentially damaging effects on plastic.Waterproof Seal — All RailMount NavPods are manufactured with a double gasket system providing an excellent watertight seal. This seal provides the best protection of your Marine Electronics. NavPods are made to withstand the harshest wet offshore boating conditions. Gen3 enhancements include a thicker external silicone gasket with improved flush fit. The internal Poron Microcell Polyurethane gasket is now 50% thicker and is not subject to "compression set" like many rubber compounds. This is important when you need to open the NavPod in the future in order to service your electronics. The gasket will continue to do its job.Nickel Chrome-Plated Stainless Steel — We use all 316 stainless steel hardware that is supplied with each NavPod. Large round-head tamper-resistant screws have deeper sockets for the NavPod wrench for better holding ability when tightening than screws used on our Traditional Series NavPod. The Nickel Chrome-Plated Stainless Steel tamper-resistant screws provide security combined with a little style!
$525.59
-
Navpod NAVPOD RMX4800-10 Railmount for Garmin GPSMAP 8410/8610
NAVPOD RMX480010 RailMountModel: RMX4800-10RailMount Pre-Cut for Garmin GPSMAP 8410xsv/8610xsv (fits 1" or 1.25" tubing)RailMount NavPods are best used for mounting of an autopilot control, sailing instrument, or small chartplotter onto an existing pedestal guard. Fits onto any 1" or 1.25" diameter tube. A Nickel Chrome-Plated Stainless Steel arm is used to mount a NavPod. The NavPod can rotate 180 degrees for easy viewing while sitting under the dodger on a rainy day. All wiring runs from the NavPod, down the center of the stainless steel arm, and into the pedestal guard. This application provides a clean and sturdy installation for electronics, without replacement of the pedestal guard.RailMounts are designed for all popular standard size instruments as well as 7 and 9 inch chartplotters.Structural Rigidity — The Gen3 enhancements now include a thicker gauge acrylic capped ABS material that improves strength and provides better structural rigidity. This thicker material allows for a larger waterproof seal. The better the structural rigidity, the less flexing when tightening and more uniform pressure on the seal. The excellent UV stability of the acrylic is combined with the durability of the ABS. The acrylic cap protects the ABS from UV and its potentially damaging effects on plastic.Waterproof Seal — All RailMount NavPods are manufactured with a double gasket system providing an excellent watertight seal. This seal provides the best protection of your Marine Electronics. NavPods are made to withstand the harshest wet offshore boating conditions. Gen3 enhancements include a thicker external silicone gasket with improved flush fit. The internal Poron Microcell Polyurethane gasket is now 50% thicker and is not subject to "compression set" like many rubber compounds. This is important when you need to open the NavPod in the future in order to service your electronics. The gasket will continue to do its job.Nickel Chrome-Plated Stainless Steel — We use all 316 stainless steel hardware that is supplied with each NavPod. Large round-head tamper-resistant screws have deeper sockets for the NavPod wrench for better holding ability when tightening than screws used on our Traditional Series NavPod. The Nickel Chrome-Plated Stainless Steel tamper-resistant screws provide security combined with a little style!Commitment to Quality — We stand behind our commitment by offering a 10-year warranty on all new Gen3 NavPods.
$525.59
-
Navpod NAVPOD RMX4800-07 Railmount for Raymarine AXIOM 9
NAVPOD RMX4800-07 RailmountModel: RMX4800-07RailMount Pre-Cut for Raymarine AXIOM 9 (Pre-Cut is for Surface Mount using rear mounting brackets, Requires Raymarine Right Angle Connector) (fits 1" or 1.25" tubing)Railmount NavPods are best used for mounting of an autopilot control, sailing instrument, or small chartplotter onto an existing pedestal guard. Fits onto any 1" or 1.25" diameter tube. A Nickel Chrome-Plated Stainless Steel arm is used to mount a NavPod. The NavPod can rotate 180 degrees for easy viewing while sitting under the dodger on a rainy day. All wiring runs from the NavPod, down the center of the stainless steel arm, and into the pedestal guard. This application provides a clean and sturdy installation for electronics, without replacement of the pedestal guard.Railmounts are designed for all popular standard size instruments as well as 7 and 9 inch chartplotters.Structural Rigidity — The Gen3 enhancements now include a thicker gauge acrylic capped ABS material that improves strength and provides better structural rigidity. This thicker material allows for a larger waterproof seal. The better the structural rigidity, the less flexing when tightening and more uniform pressure on the seal. The excellent UV stability of the acrylic is combined with the durability of the ABS. The acrylic cap protects the ABS from UV and its potentially damaging effects on plastic.Waterproof Seal — All Railmount NavPods are manufactured with a double gasket system providing an excellent watertight seal. This seal provides the best protection of your Marine Electronics. NavPods are made to withstand the harshest wet offshore boating conditions. Gen3 enhancements include a thicker external silicone gasket with improved flush fit. The internal Poron Microcell Polyurethane gasket is now 50% thicker and is not subject to "compression set" like many rubber compounds. This is important when you need to open the NavPod in the future in order to service your electronics. The gasket will continue to do its job.Nickel Chrome-Plated Stainless Steel — We use all 316 stainless steel hardware that is supplied with each NavPod. Large round-head tamper-resistant screws have deeper sockets for the NavPod wrench for better holding ability when tightening than screws used on our Traditional Series NavPod. The Nickel Chrome-Plated Stainless Steel tamper-resistant screws provide security combined with a little style!
$525.59
-
Navpod Navpod RMX4800 Railmount Pod UN-CUT
NavPod RMX4800 RailMount NavPod Un-Cut RailMount NavPods are best used for mounting of an autopilot control, sailing instrument, or small chartplotter onto an existing pedestal guard. Fits onto any 1" or 1.25" diameter tube. A Chromed Stainless Steel arm is used to mount a NavPod. The NavPod can rotate 180 degrees for easy viewing while sitting under the dodger on a rainy day. All wire run from the NavPod, down the center of the stainless steel arm, and into the pedestal guard. This application provides a clean and sturdy installation for electronics, without replacement of the pedestal guard. H W D Overall Size 9" 10.2" 6" Usable Face 5.6" 8.9" 3.75" Max Cutout 4.625" 8" All RailMount NavPods include Acrylic capped ABS plastic Chromed stainless steel tamper-proof fasteners Double Seal for watertight integrity Models are available pre-cut for popular electronics. Chromed stainless steel arm with swivel mount Both sets of adaptors included for 1" or 1.25" diameter tubing
$508.08
-
Navpod NAVPOD RMX4600-13 Railmount for Furuno GP1971F 9" GPS
NAVPOD RMX4600-13 RailmountModel: RMX4600-13RailMount Pre-Cut for Furuno GP1971F 9? Multi Touch GPS / Chartplotter / Fish Finder (fits 1" or 1.25" tubing)RailMount NavPods are best used for mounting of an autopilot control, sailing instrument, or small chartplotter onto an existing pedestal guard. Fits onto any 1" or 1.25" diameter tube. A Nickel Chrome-Plated Stainless Steel arm is used to mount a NavPod. The NavPod can rotate 180 degrees for easy viewing while sitting under the dodger on a rainy day. All wiring runs from the NavPod, down the center of the stainless steel arm, and into the pedestal guard. This application provides a clean and sturdy installation for electronics, without replacement of the pedestal guard.RailMounts are designed for all popular standard size instruments as well as 7 and 9 inch chartplotters.Structural Rigidity — The Gen3 enhancements now include a thicker gauge acrylic capped ABS material that improves strength and provides better structural rigidity. This thicker material allows for a larger waterproof seal. The better the structural rigidity, the less flexing when tightening and more uniform pressure on the seal. The excellent UV stability of the acrylic is combined with the durability of the ABS. The acrylic cap protects the ABS from UV and its potentially damaging effects on plastic.Waterproof Seal — All RailMount NavPods are manufactured with a double gasket system providing an excellent watertight seal. This seal provides the best protection of your Marine Electronics. NavPods are made to withstand the harshest wet offshore boating conditions. Gen3 enhancements include a thicker external silicone gasket with improved flush fit. The internal Poron Microcell Polyurethane gasket is now 50% thicker and is not subject to "compression set" like many rubber compounds. This is important when you need to open the NavPod in the future in order to service your electronics. The gasket will continue to do its job.Nickel Chrome-Plated Stainless Steel — We use all 316 stainless steel hardware that is supplied with each NavPod. Large round-head tamper-resistant screws have deeper sockets for the NavPod wrench for better holding ability when tightening than screws used on our Traditional Series NavPod. The Nickel Chrome-Plated Stainless Steel tamper-resistant screws provide security combined with a little style!
$499.31
-
Navpod NAVPOD RMX4600-08 Railmount for Lowrance HDS-9 Gen2
NAVPOD RMX4600-08 RailmountModel: RMX4600-08RailMount Pre-Cut for Lowrance HDS-9 Gen2 Touch / HDS-9 Gen3 / HDS Carbon 9 (fits 1" or 1.25" tubing)RailMount NavPods are best used for mounting of an autopilot control, sailing instrument, or small chartplotter onto an existing pedestal guard. Fits onto any 1" or 1.25" diameter tube. A Nickel Chrome-Plated Stainless Steel arm is used to mount a NavPod. The NavPod can rotate 180 degrees for easy viewing while sitting under the dodger on a rainy day. All wiring runs from the NavPod, down the center of the stainless steel arm, and into the pedestal guard. This application provides a clean and sturdy installation for electronics, without replacement of the pedestal guard.RailMounts are designed for all popular standard size instruments as well as 7 and 9 inch chartplotters.Structural Rigidity — The Gen3 enhancements now include a thicker gauge acrylic capped ABS material that improves strength and provides better structural rigidity. This thicker material allows for a larger waterproof seal. The better the structural rigidity, the less flexing when tightening and more uniform pressure on the seal. The excellent UV stability of the acrylic is combined with the durability of the ABS. The acrylic cap protects the ABS from UV and its potentially damaging effects on plastic.Waterproof Seal — All RailMount NavPods are manufactured with a double gasket system providing an excellent watertight seal. This seal provides the best protection of your Marine Electronics. NavPods are made to withstand the harshest wet offshore boating conditions. Gen3 enhancements include a thicker external silicone gasket with improved flush fit. The internal Poron Microcell Polyurethane gasket is now 50% thicker and is not subject to "compression set" like many rubber compounds. This is important when you need to open the NavPod in the future in order to service your electronics. The gasket will continue to do its job.Nickel Chrome-Plated Stainless Steel — We use all 316 stainless steel hardware that is supplied with each NavPod. Large round-head tamper-resistant screws have deeper sockets for the NavPod wrench for better holding ability when tightening than screws used on our Traditional Series NavPod. The Nickel Chrome-Plated Stainless Steel tamper-resistant screws provide security combined with a little style!
$499.31
-
Navpod NAVPOD RMX4600-06 Railmount for Simrad NSS9 evo3
NAVPOD RMX4600-06 RailmountModel: RMX4600-06RailMount Pre-Cut for Simrad NSS9 evo3 / B&G Zeus3 9RailMount NavPods are best used for mounting of an autopilot control, sailing instrument, or small chartplotter onto an existing pedestal guard. Fits onto any 1" or 1.25" diameter tube. A Nickel Chrome-Plated Stainless Steel arm is used to mount a NavPod. The NavPod can rotate 180 degrees for easy viewing while sitting under the dodger on a rainy day. All wiring runs from the NavPod, down the center of the stainless steel arm, and into the pedestal guard. This application provides a clean and sturdy installation for electronics, without replacement of the pedestal guard.RailMounts are designed for all popular standard size instruments as well as 7 and 9 inch chartplotters.Structural Rigidity — The Gen3 enhancements now include a thicker gauge acrylic capped ABS material that improves strength and provides better structural rigidity. This thicker material allows for a larger waterproof seal. The better the structural rigidity, the less flexing when tightening and more uniform pressure on the seal. The excellent UV stability of the acrylic is combined with the durability of the ABS. The acrylic cap protects the ABS from UV and its potentially damaging effects on plastic.Waterproof Seal — All RailMount NavPods are manufactured with a double gasket system providing an excellent watertight seal. This seal provides the best protection of your Marine Electronics. NavPods are made to withstand the harshest wet offshore boating conditions. Gen3 enhancements include a thicker external silicone gasket with improved flush fit. The internal Poron Microcell Polyurethane gasket is now 50% thicker and is not subject to "compression set" like many rubber compounds. This is important when you need to open the NavPod in the future in order to service your electronics. The gasket will continue to do its job.Nickel Chrome-Plated Stainless Steel — We use all 316 stainless steel hardware that is supplied with each NavPod. Large round-head tamper-resistant screws have deeper sockets for the NavPod wrench for better holding ability when tightening than screws used on our Traditional Series NavPod. The Nickel Chrome-Plated Stainless Steel tamper-resistant screws provide security combined with a little style!
$499.31
-
Navpod NAVPOD RMX4600-04 Railmount for Simrad NSS9 evo2
NAVPOD RMX4600-04 RailmountModel: RMX4600-04 Full Image RailMount Pre-Cut for Simrad NSS9 evo /B&G Zeus 9RailMount NavPods are best used for mounting of an autopilot control, sailing instrument, or small chartplotter onto an existing pedestal guard. Fits onto any 1" or 1.25" diameter tube. A Nickel Chrome-Plated Stainless Steel arm is used to mount a NavPod. The NavPod can rotate 180 degrees for easy viewing while sitting under the dodger on a rainy day. All wiring runs from the NavPod, down the center of the stainless steel arm, and into the pedestal guard. This application provides a clean and sturdy installation for electronics, without replacement of the pedestal guard.RailMounts are designed for all popular standard size instruments as well as 7 and 9 inch chartplotters.Structural Rigidity — The Gen3 enhancements now include a thicker gauge acrylic capped ABS material that improves strength and provides better structural rigidity. This thicker material allows for a larger waterproof seal. The better the structural rigidity, the less flexing when tightening and more uniform pressure on the seal. The excellent UV stability of the acrylic is combined with the durability of the ABS. The acrylic cap protects the ABS from UV and its potentially damaging effects on plastic.Waterproof Seal — All RailMount NavPods are manufactured with a double gasket system providing an excellent watertight seal. This seal provides the best protection of your Marine Electronics. NavPods are made to withstand the harshest wet offshore boating conditions. Gen3 enhancements include a thicker external silicone gasket with improved flush fit. The internal Poron Microcell Polyurethane gasket is now 50% thicker and is not subject to "compression set" like many rubber compounds. This is important when you need to open the NavPod in the future in order to service your electronics. The gasket will continue to do its job.Nickel Chrome-Plated Stainless Steel — We use all 316 stainless steel hardware that is supplied with each NavPod. Large round-head tamper-resistant screws have deeper sockets for the NavPod wrench for better holding ability when tightening than screws used on our Traditional Series NavPod. The Nickel Chrome-Plated Stainless Steel tamper-resistant screws provide security combined with a little style!
$499.31
-
Navpod NAVPOD RMX4600 Railmount Un-Cut
NAVPOD RMX4600 RailmountModel: RMX4600RailMount Un-Cut (usable face = 11.125"w x 6.5"h)(28.2cm w x 16.5cm h)RailMount NavPods are best used for mounting of an autopilot control, sailing instrument, or small chartplotter onto an existing pedestal guard. Fits onto any 1" or 1.25" diameter tube. A Nickel Chrome-Plated Stainless Steel arm is used to mount a NavPod. The NavPod can rotate 180 degrees for easy viewing while sitting under the dodger on a rainy day. All wiring runs from the NavPod, down the center of the stainless steel arm, and into the pedestal guard. This application provides a clean and sturdy installation for electronics, without replacement of the pedestal guard.RailMounts are designed for all popular standard size instruments as well as 7 and 9 inch chartplotters.Structural Rigidity — The Gen3 enhancements now include a thicker gauge acrylic capped ABS material that improves strength and provides better structural rigidity. This thicker material allows for a larger waterproof seal. The better the structural rigidity, the less flexing when tightening and more uniform pressure on the seal. The excellent UV stability of the acrylic is combined with the durability of the ABS. The acrylic cap protects the ABS from UV and its potentially damaging effects on plastic.Waterproof Seal — All RailMount NavPods are manufactured with a double gasket system providing an excellent watertight seal. This seal provides the best protection of your Marine Electronics. NavPods are made to withstand the harshest wet offshore boating conditions. Gen3 enhancements include a thicker external silicone gasket with improved flush fit. The internal Poron Microcell Polyurethane gasket is now 50% thicker and is not subject to "compression set" like many rubber compounds. This is important when you need to open the NavPod in the future in order to service your electronics. The gasket will continue to do its job.Nickel Chrome-Plated Stainless Steel — We use all 316 stainless steel hardware that is supplied with each NavPod. Large round-head tamper-resistant screws have deeper sockets for the NavPod wrench for better holding ability when tightening than screws used on our Traditional Series NavPod. The Nickel Chrome-Plated Stainless Steel tamper-resistant screws provide security combined with a little style!1
$481.79
-
Navpod NAVPOD RMX4500-09 Railmount for Simrad NSS7 evo3
NAVPOD RMX4500-09 RailmountModel: RMX4500-09RailMount Pre-Cut for Simrad NSS7 evo3 / B&G Zeus3 7RailMount NavPods are best used for mounting of an autopilot control, sailing instrument, or small chartplotter onto an existing pedestal guard. Fits onto any 1" or 1.25" diameter tube. A Nickel Chrome-Plated Stainless Steel arm is used to mount a NavPod. The NavPod can rotate 180 degrees for easy viewing while sitting under the dodger on a rainy day. All wiring runs from the NavPod, down the center of the stainless steel arm, and into the pedestal guard. This application provides a clean and sturdy installation for electronics, without replacement of the pedestal guard.RailMounts are designed for all popular standard size instruments as well as 7 and 9 inch chartplotters.Structural Rigidity — The Gen3 enhancements now include a thicker gauge acrylic capped ABS material that improves strength and provides better structural rigidity. This thicker material allows for a larger waterproof seal. The better the structural rigidity, the less flexing when tightening and more uniform pressure on the seal. The excellent UV stability of the acrylic is combined with the durability of the ABS. The acrylic cap protects the ABS from UV and its potentially damaging effects on plastic.Waterproof Seal — All RailMount NavPods are manufactured with a double gasket system providing an excellent watertight seal. This seal provides the best protection of your Marine Electronics. NavPods are made to withstand the harshest wet offshore boating conditions. Gen3 enhancements include a thicker external silicone gasket with improved flush fit. The internal Poron Microcell Polyurethane gasket is now 50% thicker and is not subject to "compression set" like many rubber compounds. This is important when you need to open the NavPod in the future in order to service your electronics. The gasket will continue to do its job.Nickel Chrome-Plated Stainless Steel — We use all 316 stainless steel hardware that is supplied with each NavPod. Large round-head tamper-resistant screws have deeper sockets for the NavPod wrench for better holding ability when tightening than screws used on our Traditional Series NavPod. The Nickel Chrome-Plated Stainless Steel tamper-resistant screws provide security combined with a little style!Specifications Overall Size NavPod Height 7.69 Width 11.86 Depth 5.5 Overall Size Assembly Height 10.5 Width 13.91 Depth 6.3 Usable Face Height 6 Width 9.95 Depth 4.125 Max Cutout Height 5.5 Width 9.5
$481.79
-
Navpod NAVPOD RMX4500-08 Railmount for GARMIN GPSMAP 942/922
NAVPOD RMX4500-08 RailmountModel: RMX4500-08RailMount Pre-Cut for Garmin GPSMAP 942xs/942/922xs/922RailMount NavPods are best used for mounting of an autopilot control, sailing instrument, or small chartplotter onto an existing pedestal guard. Fits onto any 1" or 1.25" diameter tube. A Nickel Chrome-Plated Stainless Steel arm is used to mount a NavPod. The NavPod can rotate 180 degrees for easy viewing while sitting under the dodger on a rainy day. All wiring runs from the NavPod, down the center of the stainless steel arm, and into the pedestal guard. This application provides a clean and sturdy installation for electronics, without replacement of the pedestal guard.RailMounts are designed for all popular standard size instruments as well as 7 and 9 inch chartplotters.Structural Rigidity — The Gen3 enhancements now include a thicker gauge acrylic capped ABS material that improves strength and provides better structural rigidity. This thicker material allows for a larger waterproof seal. The better the structural rigidity, the less flexing when tightening and more uniform pressure on the seal. The excellent UV stability of the acrylic is combined with the durability of the ABS. The acrylic cap protects the ABS from UV and its potentially damaging effects on plastic.Waterproof Seal — All RailMount NavPods are manufactured with a double gasket system providing an excellent watertight seal. This seal provides the best protection of your Marine Electronics. NavPods are made to withstand the harshest wet offshore boating conditions. Gen3 enhancements include a thicker external silicone gasket with improved flush fit. The internal Poron Microcell Polyurethane gasket is now 50% thicker and is not subject to "compression set" like many rubber compounds. This is important when you need to open the NavPod in the future in order to service your electronics. The gasket will continue to do its job.Nickel Chrome-Plated Stainless Steel — We use all 316 stainless steel hardware that is supplied with each NavPod. Large round-head tamper-resistant screws have deeper sockets for the NavPod wrench for better holding ability when tightening than screws used on our Traditional Series NavPod. The Nickel Chrome-Plated Stainless Steel tamper-resistant screws provide security combined with a little style!Specifications Overall Size NavPod Height 7.69 Width 11.86 Depth 5.5 Overall Size Assembly Height 10.5 Width 13.91 Depth 6.3 Usable Face Height 6 Width 9.95 Depth 4.125 Max Cutout Height 5.5 Width 9.5
$481.79
-
Navpod NAVPOD RMX4500-02 Railmount for Raymarine eS75/77/78
NAVPOD RMX4500-02 RailmountModel: RMX4500-02RailMount Pre-Cut for Raymarine eS75/eS77/eS78RailMount NavPods are best used for mounting of an autopilot control, sailing instrument, or small chartplotter onto an existing pedestal guard. Fits onto any 1" or 1.25" diameter tube. A Nickel Chrome-Plated Stainless Steel arm is used to mount a NavPod. The NavPod can rotate 180 degrees for easy viewing while sitting under the dodger on a rainy day. All wiring runs from the NavPod, down the center of the stainless steel arm, and into the pedestal guard. This application provides a clean and sturdy installation for electronics, without replacement of the pedestal guard.RailMounts are designed for all popular standard size instruments as well as 7 and 9 inch chartplotters.Structural Rigidity — The Gen3 enhancements now include a thicker gauge acrylic capped ABS material that improves strength and provides better structural rigidity. This thicker material allows for a larger waterproof seal. The better the structural rigidity, the less flexing when tightening and more uniform pressure on the seal. The excellent UV stability of the acrylic is combined with the durability of the ABS. The acrylic cap protects the ABS from UV and its potentially damaging effects on plastic.Waterproof Seal — All RailMount NavPods are manufactured with a double gasket system providing an excellent watertight seal. This seal provides the best protection of your Marine Electronics. NavPods are made to withstand the harshest wet offshore boating conditions. Gen3 enhancements include a thicker external silicone gasket with improved flush fit. The internal Poron Microcell Polyurethane gasket is now 50% thicker and is not subject to "compression set" like many rubber compounds. This is important when you need to open the NavPod in the future in order to service your electronics. The gasket will continue to do its job.Nickel Chrome-Plated Stainless Steel — We use all 316 stainless steel hardware that is supplied with each NavPod. Large round-head tamper-resistant screws have deeper sockets for the NavPod wrench for better holding ability when tightening than screws used on our Traditional Series NavPod. The Nickel Chrome-Plated Stainless Steel tamper-resistant screws provide security combined with a little style!Specifications Overall Size NavPod Height 7.69 Width 11.86 Depth 5.5 Overall Size Assembly Height 10.5 Width 13.91 Depth 6.3 Usable Face Height 6 Width 9.95 Depth 4.125 Max Cutout Height 5.5 Width 9.5
$481.79
-
Navpod NAVPOD RMX4500 Railmount Un-Cut
NAVPOD RMX4500 RailmountModel: RMX4500RailMount Un-Cut (usable face = 10"w x 6.5"h)(25.4cm w x 16.5cm h)RailMount NavPods are best used for mounting of an autopilot control, sailing instrument, or small chartplotter onto an existing pedestal guard. Fits onto any 1" or 1.25" diameter tube. A Nickel Chrome-Plated Stainless Steel arm is used to mount a NavPod. The NavPod can rotate 180 degrees for easy viewing while sitting under the dodger on a rainy day. All wiring runs from the NavPod, down the center of the stainless steel arm, and into the pedestal guard. This application provides a clean and sturdy installation for electronics, without replacement of the pedestal guard.RailMounts are designed for all popular standard size instruments as well as 7 and 9 inch chartplotters.Structural Rigidity — The Gen3 enhancements now include a thicker gauge acrylic capped ABS material that improves strength and provides better structural rigidity. This thicker material allows for a larger waterproof seal. The better the structural rigidity, the less flexing when tightening and more uniform pressure on the seal. The excellent UV stability of the acrylic is combined with the durability of the ABS. The acrylic cap protects the ABS from UV and its potentially damaging effects on plastic.Waterproof Seal — All RailMount NavPods are manufactured with a double gasket system providing an excellent watertight seal. This seal provides the best protection of your Marine Electronics. NavPods are made to withstand the harshest wet offshore boating conditions. Gen3 enhancements include a thicker external silicone gasket with improved flush fit. The internal Poron Microcell Polyurethane gasket is now 50% thicker and is not subject to "compression set" like many rubber compounds. This is important when you need to open the NavPod in the future in order to service your electronics. The gasket will continue to do its job.Nickel Chrome-Plated Stainless Steel — We use all 316 stainless steel hardware that is supplied with each NavPod. Large round-head tamper-resistant screws have deeper sockets for the NavPod wrench for better holding ability when tightening than screws used on our Traditional Series NavPod. The Nickel Chrome-Plated Stainless Steel tamper-resistant screws provide security combined with a little style!Specifications Overall Size NavPod Height 7.69 Width 11.86 Depth 5.5 Overall Size Assembly Height 10.5 Width 13.91 Depth 6.3 Usable Face Height 6 Width 9.95 Depth 4.125 Max Cutout Height 5.5 Width 9.5
$464.28
-
Navpod NAVPOD RMX4408 Railmount for Simrad NSS7
NAVPOD RMX4408 RailmountModel: RMX4408RailMount Pre-Cut for Simrad GO7/B&G Vulcan 7 (Pre Nov. 2017) (fits 1" or 1.25" tubing)RailMount NavPods are best used for mounting of an autopilot control, sailing instrument, or small chartplotter onto an existing pedestal guard. Fits onto any 1" or 1.25" diameter tube. A Nickel Chrome-Plated Stainless Steel arm is used to mount a NavPod. The NavPod can rotate 180 degrees for easy viewing while sitting under the dodger on a rainy day. All wiring runs from the NavPod, down the center of the stainless steel arm, and into the pedestal guard. This application provides a clean and sturdy installation for electronics, without replacement of the pedestal guard.RailMounts are designed for all popular standard size instruments as well as 7 and 9 inch chartplotters.Structural Rigidity — The Gen3 enhancements now include a thicker gauge acrylic capped ABS material that improves strength and provides better structural rigidity. This thicker material allows for a larger waterproof seal. The better the structural rigidity, the less flexing when tightening and more uniform pressure on the seal. The excellent UV stability of the acrylic is combined with the durability of the ABS. The acrylic cap protects the ABS from UV and its potentially damaging effects on plastic.Waterproof Seal — All RailMount NavPods are manufactured with a double gasket system providing an excellent watertight seal. This seal provides the best protection of your Marine Electronics. NavPods are made to withstand the harshest wet offshore boating conditions. Gen3 enhancements include a thicker external silicone gasket with improved flush fit. The internal Poron Microcell Polyurethane gasket is now 50% thicker and is not subject to "compression set" like many rubber compounds. This is important when you need to open the NavPod in the future in order to service your electronics. The gasket will continue to do its job.Nickel Chrome-Plated Stainless Steel — We use all 316 stainless steel hardware that is supplied with each NavPod. Large round-head tamper-resistant screws have deeper sockets for the NavPod wrench for better holding ability when tightening than screws used on our Traditional Series NavPod. The Nickel Chrome-Plated Stainless Steel tamper-resistant screws provide security combined with a little style!Specifications Overall Size Height in 10.5 cm 26.7 Width in 12.5 cm 31.8 Depth in 5.92 cm 15.0 Usable Face Height in 6 cm 15.2 Width 8.75 cm 22.2 Depth in 3.25 cm 8.3 Max Cutout Height in 5.5 cm 14.0 Width in 8.625 cm 21.9
$473.03
-
Navpod NAVPOD RMX4407 Railmount for Simrad NSS7
NAVPOD RMX4407 RailmountModel: RMX4407RailMount Pre-Cut for Simrad NSS7/B&G Zeus Touch 7RailMount NavPods are best used for mounting of an autopilot control, sailing instrument, or small chartplotter onto an existing pedestal guard. Fits onto any 1" or 1.25" diameter tube. A Nickel Chrome-Plated Stainless Steel arm is used to mount a NavPod. The NavPod can rotate 180 degrees for easy viewing while sitting under the dodger on a rainy day. All wiring runs from the NavPod, down the center of the stainless steel arm, and into the pedestal guard. This application provides a clean and sturdy installation for electronics, without replacement of the pedestal guard.RailMounts are designed for all popular standard size instruments as well as 7 and 9 inch chartplotters.Structural Rigidity — The Gen3 enhancements now include a thicker gauge acrylic capped ABS material that improves strength and provides better structural rigidity. This thicker material allows for a larger waterproof seal. The better the structural rigidity, the less flexing when tightening and more uniform pressure on the seal. The excellent UV stability of the acrylic is combined with the durability of the ABS. The acrylic cap protects the ABS from UV and its potentially damaging effects on plastic.Waterproof Seal — All RailMount NavPods are manufactured with a double gasket system providing an excellent watertight seal. This seal provides the best protection of your Marine Electronics. NavPods are made to withstand the harshest wet offshore boating conditions. Gen3 enhancements include a thicker external silicone gasket with improved flush fit. The internal Poron Microcell Polyurethane gasket is now 50% thicker and is not subject to "compression set" like many rubber compounds. This is important when you need to open the NavPod in the future in order to service your electronics. The gasket will continue to do its job.Nickel Chrome-Plated Stainless Steel — We use all 316 stainless steel hardware that is supplied with each NavPod. Large round-head tamper-resistant screws have deeper sockets for the NavPod wrench for better holding ability when tightening than screws used on our Traditional Series NavPod. The Nickel Chrome-Plated Stainless Steel tamper-resistant screws provide security combined with a little style!Specifications Overall Size Height in 10.5 cm 26.7 Width in 12.5 cm 31.8 Depth in 5.92 cm 15.0 Usable Face Height in 6 cm 15.2 Width 8.75 cm 22.2 Depth in 3.25 cm 8.3 Max Cutout Height in 5.5 cm 14.0 Width in 8.625 cm 21.9
$473.03
-
Navpod Navpod RMX4406 Railmount Pod PRE-CUT Simrad NSS7 evo2
NavPod RMX4400 RailMount NavPod Un-Cut RailMount NavPods are best used for mounting of an autopilot control, sailing instrument, or small chartplotter onto an existing pedestal guard. Fits onto any 1" or 1.25" diameter tube. A Chromed Stainless Steel arm is used to mount a NavPod. The NavPod can rotate 180 degrees for easy viewing while sitting under the dodger on a rainy day. All wire run from the NavPod, down the center of the stainless steel arm, and into the pedestal guard. This application provides a clean and sturdy installation for electronics, without replacement of the pedestal guard. H W D Overall Size 9" 10.2" 6" Usable Face 5.6" 8.9" 3.75" Max Cutout 4.625" 8" All RailMount NavPods include Acrylic capped ABS plastic Chromed stainless steel tamper-proof fasteners Double Seal for watertight integrity Models are available pre-cut for popular electronics. Chromed stainless steel arm with swivel mount Both sets of adaptors included for 1" or 1.25"diameter tubing
$473.03
-
Navpod Navpod RMX4405 Railmount Pod PRE-CUT Furuno GP1670F
NavPod RMX4405 RailMount NavPod Pre-Cut for Furuno GP1670 / 1670F 5.7" RailMount NavPods are best used for mounting of an autopilot control, sailing instrument, or small chartplotter onto an existing pedestal guard. Fits onto any 1": or 1.25" diameter tube. A Chromed Stainless Steel arm is used to mount a NavPod. The NavPod can rotate 180 degrees for easy viewing while sitting under the dodger on a rainy day. All wire run from the NavPod, down the center of the stainless steel arm, and into the pedestal guard. This application provides a clean and sturdy installation for electronics, without replacement of the pedestal guard. H W D Overall Size 9" 10.2" 6" Usable Face 5.6" 8.9" 3.75" Max Cutout 4.625" 8" All RailMount NavPods include Acrylic capped ABS plastic Chromed stainless steel tamper-proof fasteners Double Seal for watertight integrity Models are available pre-cut for popular electronics. Chromed stainless steel arm with swivel mount Both sets of adaptors included for 1" or 1.25" diameter tubing
$473.03
-
Navpod Navpod RMX4404 Railmount Pod PRE-CUT Raymarine A75/77/78
NavPod RMX4404 RailMount NavPod Pre-Cut for Raymarine a75 / a77 / a78 RailMount NavPods are best used for mounting of an autopilot control, sailing instrument, or small chartplotter onto an existing pedestal guard. Fits onto any 1"or 1.25" diameter tube. A Chromed Stainless Steel arm is used to mount a NavPod. The NavPod can rotate 180 degrees for easy viewing while sitting under the dodger on a rainy day. All wire run from the NavPod, down the center of the stainless steel arm, and into the pedestal guard. This application provides a clean and sturdy installation for electronics, without replacement of the pedestal guard. H W D Overall Size 9" 10.2" 6" Usable Face 5.6" 8.9" 3.75" Max Cutout 4.625" 8" All RailMount NavPods include Acrylic capped ABS plastic Chromed stainless steel tamper-proof fasteners Double Seal for watertight integrity Models are available pre-cut for popular electronics. Chromed stainless steel arm with swivel mount Both sets of adaptors included for 1" or 1.25" diameter tubing
$473.03
-
Navpod Navpod RMX4402 Railmount Pod PRE-CUT Raymarine E7
NavPod RMX4402 RailMount NavPod Pre-Cut for Raymarine e7 (1" or 1.25" tubing) RailMount NavPods are best used for mounting of an autopilot control, sailing instrument, or small chartplotter onto an existing pedestal guard. Fits onto any 1" or 1.25" diameter tube. A Chromed Stainless Steel arm is used to mount a NavPod. The NavPod can rotate 180 degrees for easy viewing while sitting under the dodger on a rainy day. All wire run from the NavPod, down the center of the stainless steel arm, and into the pedestal guard. This application provides a clean and sturdy installation for electronics, without replacement of the pedestal guard. H W D Overall Size 9" 10.2" 6" Usable Face 5.6" 8.9" 3.75" Max Cutout 4.625" 8" All RailMount NavPods include Acrylic capped ABS plastic Chromed stainless steel tamper-proof fasteners Double Seal for watertight integrity Models are available pre-cut for popular electronics. Chromed stainless steel arm with swivel mount Both sets of adaptors included for 1" or 1.25"diameter tubing
$473.03
-
Navpod Navpod RMX4401 Railmount Pod PRE-CUT For Garmin 720/740
NavPod RMX4401 RailMount Pre-Cut for Garmin 720/721/740/740s/741/721xs/741xs/70s/70dv (1" or 1.25" tubing) RailMount NavPods are best used for mounting of an autopilot control, sailing instrument, or small chartplotter onto an existing pedestal guard. Fits onto any 1" or 1.25" diameter tube. A Chromed Stainless Steel arm is used to mount a NavPod. The NavPod can rotate 180 degrees for easy viewing while sitting under the dodger on a rainy day. All wire run from the NavPod, down the center of the stainless steel arm, and into the pedestal guard. This application provides a clean and sturdy installation for electronics, without replacement of the pedestal guard. H W D Overall Size 9" 10.2" 6" Usable Face 5.6" 8.9" 3.75" Max Cutout 4.625" 8" All RailMount NavPods include Acrylic capped ABS plastic Chromed stainless steel tamper-proof fasteners Double Seal for watertight integrity Models are available pre-cut for popular electronics. Chromed stainless steel arm with swivel mount Both sets of adaptors included for 1" or 1.25" diameter tubing
$473.03
-
Navpod NAVPOD RMX4400-13 Railmount for Furuno GP1871F
NAVPOD RMX4400-13 RailmountModel: RMX4400-13RailMount Pre-Cut for Furuno GP1871F 7? Multi Touch GPS/WAAS Chart Plotter with CHIRP and Conventional Fish Finder (fits 1" or 1.25" tubing)RailMount NavPods are best used for mounting of an autopilot control, sailing instrument, or small chartplotter onto an existing pedestal guard. Fits onto any 1" or 1.25" diameter tube. A Nickel Chrome-Plated Stainless Steel arm is used to mount a NavPod. The NavPod can rotate 180 degrees for easy viewing while sitting under the dodger on a rainy day. All wiring runs from the NavPod, down the center of the stainless steel arm, and into the pedestal guard. This application provides a clean and sturdy installation for electronics, without replacement of the pedestal guard.RailMounts are designed for all popular standard size instruments as well as 7 and 9 inch chartplotters.Structural Rigidity — The Gen3 enhancements now include a thicker gauge acrylic capped ABS material that improves strength and provides better structural rigidity. This thicker material allows for a larger waterproof seal. The better the structural rigidity, the less flexing when tightening and more uniform pressure on the seal. The excellent UV stability of the acrylic is combined with the durability of the ABS. The acrylic cap protects the ABS from UV and its potentially damaging effects on plastic.Waterproof Seal — All RailMount NavPods are manufactured with a double gasket system providing an excellent watertight seal. This seal provides the best protection of your Marine Electronics. NavPods are made to withstand the harshest wet offshore boating conditions. Gen3 enhancements include a thicker external silicone gasket with improved flush fit. The internal Poron Microcell Polyurethane gasket is now 50% thicker and is not subject to "compression set" like many rubber compounds. This is important when you need to open the NavPod in the future in order to service your electronics. The gasket will continue to do its job.Nickel Chrome-Plated Stainless Steel — We use all 316 stainless steel hardware that is supplied with each NavPod. Large round-head tamper-resistant screws have deeper sockets for the NavPod wrench for better holding ability when tightening than screws used on our Traditional Series NavPod. The Nickel Chrome-Plated Stainless Steel tamper-resistant screws provide security combined with a little style!Specifications Overall Size Height in 10.5 cm 26.7 Width in 12.5 cm 31.8 Depth in 5.92 cm 15.0 Usable Face Height in 6 cm 15.2 Width 8.75 cm 22.2 Depth in 3.25 cm 8.3 Max Cutout Height in 5.5 cm 14.0 Width in 8.625 cm 21.9
$473.03
-
Navpod NAVPOD RMX4400-12 Railmount for Simrad GO7-XSR
NAVPOD RMX4400-12 RailmountModel: RMX4400-12RailMount Pre-Cut for Simrad GO7 XSE, GO7 XSR/B&G Vulcan 7R (fits 1" or 1.25" tubing)RailMount NavPods are best used for mounting of an autopilot control, sailing instrument, or small chartplotter onto an existing pedestal guard. Fits onto any 1" or 1.25" diameter tube. A Nickel Chrome-Plated Stainless Steel arm is used to mount a NavPod. The NavPod can rotate 180 degrees for easy viewing while sitting under the dodger on a rainy day. All wiring runs from the NavPod, down the center of the stainless steel arm, and into the pedestal guard. This application provides a clean and sturdy installation for electronics, without replacement of the pedestal guard.RailMounts are designed for all popular standard size instruments as well as 7 and 9 inch chartplotters.Structural Rigidity — The Gen3 enhancements now include a thicker gauge acrylic capped ABS material that improves strength and provides better structural rigidity. This thicker material allows for a larger waterproof seal. The better the structural rigidity, the less flexing when tightening and more uniform pressure on the seal. The excellent UV stability of the acrylic is combined with the durability of the ABS. The acrylic cap protects the ABS from UV and its potentially damaging effects on plastic.Waterproof Seal — All RailMount NavPods are manufactured with a double gasket system providing an excellent watertight seal. This seal provides the best protection of your Marine Electronics. NavPods are made to withstand the harshest wet offshore boating conditions. Gen3 enhancements include a thicker external silicone gasket with improved flush fit. The internal Poron Microcell Polyurethane gasket is now 50% thicker and is not subject to "compression set" like many rubber compounds. This is important when you need to open the NavPod in the future in order to service your electronics. The gasket will continue to do its job.Nickel Chrome-Plated Stainless Steel — We use all 316 stainless steel hardware that is supplied with each NavPod. Large round-head tamper-resistant screws have deeper sockets for the NavPod wrench for better holding ability when tightening than screws used on our Traditional Series NavPod. The Nickel Chrome-Plated Stainless Steel tamper-resistant screws provide security combined with a little style!Specifications Overall Size Height in 10.5 cm 26.7 Width in 12.5 cm 31.8 Depth in 5.92 cm 15.0 Usable Face Height in 6 cm 15.2 Width 8.75 cm 22.2 Depth in 3.25 cm 8.3 Max Cutout Height in 5.5 cm 14.0 Width in 8.625 cm 21.9
$473.03
-
Navpod NAVPOD RMX4400-11 Railmount for Raymarine AXIOM 7
NAVPOD RMX4400-11 RailmountModel: RMX4400-11RailMount Pre-Cut for Raymarine AXIOM 7 (No Sonar)RailMount NavPods are best used for mounting of an autopilot control, sailing instrument, or small chartplotter onto an existing pedestal guard. Fits onto any 1" or 1.25" diameter tube. A Nickel Chrome-Plated Stainless Steel arm is used to mount a NavPod. The NavPod can rotate 180 degrees for easy viewing while sitting under the dodger on a rainy day. All wiring runs from the NavPod, down the center of the stainless steel arm, and into the pedestal guard. This application provides a clean and sturdy installation for electronics, without replacement of the pedestal guard.RailMounts are designed for all popular standard size instruments as well as 7 and 9 inch chartplotters.Structural Rigidity — The Gen3 enhancements now include a thicker gauge acrylic capped ABS material that improves strength and provides better structural rigidity. This thicker material allows for a larger waterproof seal. The better the structural rigidity, the less flexing when tightening and more uniform pressure on the seal. The excellent UV stability of the acrylic is combined with the durability of the ABS. The acrylic cap protects the ABS from UV and its potentially damaging effects on plastic.Waterproof Seal — All RailMount NavPods are manufactured with a double gasket system providing an excellent watertight seal. This seal provides the best protection of your Marine Electronics. NavPods are made to withstand the harshest wet offshore boating conditions. Gen3 enhancements include a thicker external silicone gasket with improved flush fit. The internal Poron Microcell Polyurethane gasket is now 50% thicker and is not subject to "compression set" like many rubber compounds. This is important when you need to open the NavPod in the future in order to service your electronics. The gasket will continue to do its job.Nickel Chrome-Plated Stainless Steel — We use all 316 stainless steel hardware that is supplied with each NavPod. Large round-head tamper-resistant screws have deeper sockets for the NavPod wrench for better holding ability when tightening than screws used on our Traditional Series NavPod. The Nickel Chrome-Plated Stainless Steel tamper-resistant screws provide security combined with a little style!
$473.03
-
Navpod Navpod RMX4400 Railmount Pod UN-CUT
NavPod RMX4400 RailMount NavPod Un-Cut RailMount NavPods are best used for mounting of an autopilot control, sailing instrument, or small chartplotter onto an existing pedestal guard. Fits onto any 1" or 1.25" diameter tube. A Chromed Stainless Steel arm is used to mount a NavPod. The NavPod can rotate 180 degrees for easy viewing while sitting under the dodger on a rainy day. All wire run from the NavPod, down the center of the stainless steel arm, and into the pedestal guard. This application provides a clean and sturdy installation for electronics, without replacement of the pedestal guard. H W D Overall Size 9" 10.2" 6" Usable Face 5.6" 8.9" 3.75" Max Cutout 4.625" 8" All RailMount NavPods include Acrylic capped ABS plastic Chromed stainless steel tamper-proof fasteners Double Seal for watertight integrity Models are available pre-cut for popular electronics. Chromed stainless steel arm with swivel mount Both sets of adaptors included for 1" or 1.25" diameter tubing
$455.51
-
Navpod NAVPOD RMX4102 Railmount for one Simrad IS42
NAVPOD RMX4102 RailmountModel: RMX4102RailMount Pre-Cut for one Simrad IS42 / B&G Triton /AP44 square hole instrumentRailMount NavPods are best used for mounting of an autopilot control, sailing instrument, or small chartplotter onto an existing pedestal guard. Fits onto any 1" or 1.25" diameter tube. A Nickel Chrome-Plated Stainless Steel arm is used to mount a NavPod. The NavPod can rotate 180 degrees for easy viewing while sitting under the dodger on a rainy day. All wiring runs from the NavPod, down the center of the stainless steel arm, and into the pedestal guard. This application provides a clean and sturdy installation for electronics, without replacement of the pedestal guard.RailMounts are designed for all popular standard size instruments as well as 7 and 9 inch chartplotters.Structural Rigidity — The Gen3 enhancements now include a thicker gauge acrylic capped ABS material that improves strength and provides better structural rigidity. This thicker material allows for a larger waterproof seal. The better the structural rigidity, the less flexing when tightening and more uniform pressure on the seal. The excellent UV stability of the acrylic is combined with the durability of the ABS. The acrylic cap protects the ABS from UV and its potentially damaging effects on plastic.Waterproof Seal — All RailMount NavPods are manufactured with a double gasket system providing an excellent watertight seal. This seal provides the best protection of your Marine Electronics. NavPods are made to withstand the harshest wet offshore boating conditions. Gen3 enhancements include a thicker external silicone gasket with improved flush fit. The internal Poron Microcell Polyurethane gasket is now 50% thicker and is not subject to "compression set" like many rubber compounds. This is important when you need to open the NavPod in the future in order to service your electronics. The gasket will continue to do its job.Nickel Chrome-Plated Stainless Steel — We use all 316 stainless steel hardware that is supplied with each NavPod. Large round-head tamper-resistant screws have deeper sockets for the NavPod wrench for better holding ability when tightening than screws used on our Traditional Series NavPod. The Nickel Chrome-Plated Stainless Steel tamper-resistant screws provide security combined with a little style!1
$437.99
-
Navpod Navpod RMX4101 NAV RMX4101 RAIL MOUNT 3.6 PRE CUT HOLE
NavPod RMX4101 RailMount NavPod Pre-Cut for one Raymarine P70, P70R, ST60, i50, i60, i70, Garmin GMI10, Furuno FI50, Simrad IS20, or B&G Triton Instruments (1" or 1.25" tubing) RailMount NavPods are best used for mounting of an autopilot control, sailing instrument, or small chartplotter onto an existing pedestal guard. Fits onto any 1" or 1.25" diameter tube. A Chromed Stainless Steel arm is used to mount a NavPod. The NavPod can rotate 180 degrees for easy viewing while sitting under the dodger on a rainy day. All wire run from the NavPod, down the center of the stainless steel arm, and into the pedestal guard. This application provides a clean and sturdy installation for electronics, without replacement of the pedestal guard. H W D Overall Size 7.375" 5.9" 5.375" Usable Face 4.5" 4.5" 2.75" Max Cutout 3.375" 3.375" All RailMount NavPods include Acrylic capped ABS plastic Chromed stainless steel tamper-proof fasteners Double Seal for watertight integrity Models are available pre-cut for popular electronics. Chromed stainless steel arm with swivel mount Both sets of adaptors included for 1" or 1.25" diameter tubing
$437.99
You have seen 48 out of 516 products