Swivel Bracket KitGalvanized swivel top brackets provide vertical and tilting adjustments for trailer bunks.Swivel Brackets for mounting Bunk Boards to Bolster Brackets.Features: Bunk flange holes 3/8" dia. Bunk flange 1-3/8" x 3-1/2" Swivel flange hole 1/2" dia. Swivel flange 2" tall x 3-1/2" 2-1/2" bunk flange hole centers & 1 hole centered 10 gauge material *Sold as kit with (2) brackets, (2) 7/16" x 1" head cap screws, and (2) 7/16" nylon lock nuts.

Read more less

Vertical Bunk Bracket Dimpled - 7-1/2"Adjustable bunk bracket. Used when mounting bunks on edge. Ideal for small craft trailers. A single bracket will allow the bunk board to pivot with the hull as the boat is loaded. Double brackets hold the board in place.Features: 7-1/2" Slot 7/16" x 4-3/8" 11 gauge materical, galvanized finish Dimpled style

Read more less

Bolt-On Fender Step Pad - 3" Left Hand/Right HandThis fender step pad is ideal for the do-it-yourselfer. Step pad can be welded or bolted to your trailer fender. Step pad can also be bolted to your trailer frame with u-bolts. U-bolts NOT included.Features: Galvanized Finish 12 Gauge Steel 1-3/16"H x 3"W x 15-1/4"L Left Hand/Right hand

Read more less

5' Roller BunkRoller bunks make loading and unloading small craft at very short or even dry ramps easy. Great for ramps where it is not practical to float the boat onto the trailer. Pre-assembled and pre-drilled for easy installation. May be installed using mounting brackets if lift and/or angle is needed, or may be bolted directly to trailer frame for a flat bottom boat, or even mounted on top of existing bunk boards.Features: Durable 2" polypropylene rollers on 1/2" shafts mounted in a heavy gauge pre-galvanized channel Supports up to 1500lbs of well distributed weight Mounting hardware not included Sold in pairs WARNING: This product can expose you to chemicals including ARSENIC ,CADMIUM which are known to the State of California to cause cancer or other reproductive harm, and BERYLLIUM,COBALT METAL POWDER,NICKEL (METALLIC) which are known to the State of California to cause cancer, and Chromium (hexavalent compounds),LEAD which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less

8.5" Kit Rod HolderFeatures: Rod holder is used for 1 kite rod Size: 8.5"

Read more less

Screwless Flush Mount Rod Holder - 15 Degree - Black Liner - No LogoFeatures: 316L Stainless steel 1-5/8” Inner diameter 2-1/8” Outer diameter Fits 2-3/16” hole diameter Cap size 4-1/2” long x 3-5/8” wide 9” Tube length 1/4” wide x 1/2” tall gimbal bar Cast models feature a 1/2” drain hole No logo on the cap for a sleek, low profile The liner runs the full length of the tube Each rod holder includes a backing plate and installation nut Installation requires Model # 53679 Installation Socket

Read more less

Screwless Flush Mount Rod Holder - 0 Degree - Black Liner - No LogoFeatures: 316L Stainless steel 1-5/8” Inner diameter 2-1/8” Outer diameter Fits 2-3/16” hole diameter Cap size 4-1/2” long x 3-5/8” wide 9” Tube length 1/4” wide x 1/2” tall gimbal bar Cast models feature a 1/2” drain hole No logo on the cap for a sleek, low profile The liner runs the full length of the tube Each rod holder includes a backing plate and installation nut Installation requires Model # 53679 Installation Socket

Read more less

Flush Mount Rod Holder - 30 Degree - Black Liner - No LogoFeatures: 316L Stainless steel 1-5/8” Inner diameter Fits 2-3/16” hole diameter Cap size 4-1/2” long x 3-5/8” wide 9” Tube length 1/4” wide x 1/2” tall gimbal bar Cast models feature a 1/2” drain hole The liner runs the full length of the tube Specifications: Angle: 30 Degrees Construction: Stainless Steel Box Dimensions: 4"H x 4"W x 14"L WT: 2 lbs UPC: 768296010805

Read more less

Flush Mount Rod Holder - 0 Degree - Black Liner - No LogoFeatures: 316L Stainless steel 1-5/8” Inner diameter Fits 2-3/16” hole diameter Cap size 4-1/2” long x 3-5/8” wide 9” Tube length 1/4” wide x 1/2” tall gimbal bar Cast models feature a 1/2” drain hole The liner runs the full length of the tube

Read more less

Flush Mount Rod Holder - 0 Degree - Black Liner with Drain - No LogoFeatures: 316L Stainless steel 1-5/8” Inner diameter Fits 2-3/16” hole diameter Cap size 4-1/2” long x 3-5/8” wide 9” Tube length 1/4” wide x 1/2” tall gimbal bar Cast models feature a 1/2” drain hole The liner runs the full length of the tube

Read more less

Gen3 Center Rigger Pole - Black - 2-Section - 12'12' Gen3 Carbon Fiber Center Rigger Pole is designed to prevent galvanic reactions, a common problem with anything made from carbon fiber, which keeps your poles looking good and performing at their best.The base of the poles is made of solid fiberglass for greater strength and stability. Taper-Lok joints are used to fix the pole in its extended position. The Taper-Lok joints wedge tightly together creating a single rigid one-piece pole that runs much straighter than fiberglass or aluminum poles. When ready for storage, simply unscrew and remove the locking pin from each collar and the fully rigid sections slide inside each other collapsing the pole. Taper-Lok gives you all the benefits of a single rigid pole with the added convenience of easy storage.Features: One 12’ Carbon Fiber Center Rigger Pole with integrated dual stainless eyes Mesh storage bag Integrated dual halyard 316 stainless steel eyes for running multiple halyards Extra-long nonconductive tip to prevent tangles Solid fiberglass base for greater strength and stability Designed to prevent galvanic reactions Taper-Lok joints create single rigid one-piece poles Straighter and stronger than fiberglass and aluminum poles Sections slide inside one another for collapsible storage Fits 1-1/2” pole holders without aluminum fitment sleeve Fits 1-5/8” pole holders with aluminum fitment sleeve Extended pole length 12’

Read more less

Gen2 Carbon Fiber Center Rigger Pole - 12' - White - SingleGen2 Poles are designed to prevent galvanic reactions, a common problem with anything made from carbon fiber, which keeps your poles looking good and performing at their best. The base of the poles is made of solid fiberglass for greater strength and stability.Taper-Lok joints are used to fix the pole in its extended position. The Taper-Lok joints wedge tightly together creating a single rigid one-piece pole that runs much straighter than fiberglass or aluminum poles. When ready for storage, simply unscrew and remove the locking pin from each collar and the fully rigid sections slide inside each other collapsing the pole. Taper-Lok gives you all the benefits of a single rigid pole with the added convenience of easy storage.Gen2 Carbon Fiber Poles have an extra-long non-conductive tip designed to prevent line tangles in rough waters. These poles have integrated dual 316 stainless steel halyard eyes that are designed for running multiple halyards on one pole. The smooth design of these eyes also prevents any possibility of snags.Features: Integrated dual halyard 316 stainless steel eyes for running multiple halyards Extra-long nonconductive tip to prevent tangles Solid fiberglass base for greater strength and stability Designed to prevent galvanic reactions Taper-Lok joints create single rigid one-piece poles Straighter and stronger than fiberglass and aluminum poles Sections slide inside one another for collapsible storage Specifications: Length (Feet): 12' Finish: White Diameter (Inches): 1-1/2" Construction: Carbon Fiber Box Dimensions: 5"H x 5"W x 91"L WT: 27 lbs UPC: 768296010379

Read more less

Aluminum Trident Rod HolderC.E. Smith's line of high-polished aluminum trident rod holders offers a great alternative to stainless steel.These rod holders are constructed of marine-grade aluminum that has been 100% anodized for functionality and style. Be ready to turn the one-rod holder into three with ease and efficiency.  Technical Specifications: Overall Length - 24.84" Base Angle - 0° Side Rod Holder Angle - 15° Internal Diameter - 2" *Sold as an Individual

Read more less

Flush Mount 30° Nylon Rod Holder - Black Corrosion-free nylon rod holder. These 30° light-duty fishing rod holders are an economical way to add more rod storage. Molded in one piece from UV-resistant Nylon, these rod holders are tough and corrosion-free. Features: 10" tube Cap is 4" long x 3-1/2" wide Installs into a 2-1/16" hole Mount with 3/16" screws (not included)

Read more less

Backing Plate for 70 Series Rod HoldersBacking plates are very important to have under every rod holder used for heavy tackle fishing. When the rod holder is under extreme load, regular nuts and washers can concentrate stress and cause spider cracking around your rod holders or perhaps even tear through causing severe gunnel damage. Smith backing plates distribute mounting bolt pressure evenly over 30 times more surface area than with standard washers alone. 2 sizes, one for 70 series and 80 series rod holders. Each size fits all 3 models of the Series.Features Use this backing plate for all 70 series rod holders (53670A, 53670CA, 53671A, 53671CA, 53672A, 53672CA) 316L cast stainless steel 4" x 5-1/4" 4mm thick Use your 1/4" stainless bolts and nuts (hardware not included)

Read more less

Replacement Liner for 70 Series - WhiteReplacement liner for 70 series in-gunnel and clamp-on rod holders. This UV-resistant vinyl liner protects rods.Features: Recessed liner (doesn't come to the top of the tube) Made of white vinyl material

Read more less

Flush Mount Rod Holder - 15 Degree & 9" Depth - Stainless Steel - Cast Gimbal - White Vinyl LinerThese larger 70C series models feature a beautifully rounded cast bottom end with a 1/2" tapered pipe threaded drain. Use them when the bottom of the rod holder must have a decorative appearance or add a drain tube and use it when there is dry storage space under the rod holder. This rod holder features a super tough cast stainless steel gimbal bar designed to hold up to the punishment of downriggers or heavy tackle. A white vinyl liner protects rods and is keyed to the gimbal, so the liner stays in place.Features: Safe, rounded bottom 316L Stainless Steel 1/2" pipe-threaded drain hole 9" tube Specifications: Angle: 15-degrees Inner Diameter: 1-5/8"  Outer Diameter: 2"  Cap (L x W): 4-1/2 x 3-5/8 inches Specifications: Mounting Style: Flush Length (Inches): 9" Finish: Polished Diameter (Inches): 1-5/8" Construction: Stainless Steel Angle: 15 Degrees Box Dimensions: 5"H x 5"W x 14"L WT: 2.1 lbs UPC: 768296005535

Read more less

Flush Mount Rod Holder - 30 Degree & 9" Depth - Stainless Steel - Cast Bottom - White Vinyl LinerThese larger 70C series models feature a beautifully rounded cast bottom end with a 1/2" tapered pipe threaded drain. Use them when the bottom of the rod holder must have a decorative appearance or add a drain tube and use it when there is dry storage space under the rod holder. This rod holder features a super tough cast stainless steel gimbal bar designed to hold up to the punishment of downriggers or heavy tackle. A white vinyl liner protects rods and is keyed to the gimbal, so the liner stays in place.Features: 316L stainless steel 1/2 in. threaded drain Specifications: Angle: 30-degrees Length: 9 in. Inner Diameter: 1-5/8 in. Specifications: Angle: 30 Degrees Construction: Stainless Steel Diameter (Inches): 1-5/8" Finish: Polished Length (Inches): 9" Mounting Style: Flush Box Dimensions: 4"H x 5"W x 11"L WT: 2.2 lbs UPC: 768296005542

Read more less

Flush Mount Rod Holder - 0 Degree & 9" Depth - Stainless Steel - Cast Bottom - White Vinyl LinerThese larger 70C series models feature a beautifully rounded cast bottom end with a 1/2" tapered pipe threaded drain. Use them when the bottom of the rod holder must have a decorative appearance or add a drain tube and use it when there is dry storage space under the rod holder. This rod holder features a super tough cast stainless steel gimbal bar designed to hold up to the punishment of downriggers or heavy tackle. A white vinyl liner protects rods and is keyed to the gimbal, so the liner stays in place.Features: 316L stainless steel 1/2 in. threaded drain Specifications: Angle: 0-degrees Length: 9 in. Inner Diameter: 1-5/8 in. Specifications: Angle: 0 Degrees Construction: Stainless Steel Diameter (Inches): 1-5/8" Finish: Polished Length (Inches): 9" Mounting Style: Flush Box Dimensions: 5"H x 5"W x 14"L WT: 2.15 lbs UPC: 768296005528

Read more less

Backing Plate for 80 Series Rod HoldersBacking plates are very important to have under every rod holder used for heavy tackle fishing. When the rod holder is under extreme load, regular nuts and washers can concentrate stress and cause spider cracking around your rod holders or perhaps even tear through causing severe gunnel damage. Smith backing plates distribute mounting bolt pressure evenly over 30 times more surface area than with standard washers alone. 2 sizes, one for 70 series and 80 series rod holders. Each size fits all 3 models of the Series.Features: Use this backing plate on all 80 series rod holders (53680CA, 53680SA, 53681CA, 53681SA, 53682CA, and 53682SA) 316L cast stainless steel 4-1/4" x 6" 4mm thick Use your 1/4" stainless bolts and nuts (hardware not included)

Read more less

Backing Plate for 70 Series Rod HoldersBacking plates are very important to have under every rod holder used for heavy tackle fishing. When the rod holder is under extreme load, regular nuts and washers can concentrate stress and cause spider cracking around your rod holders, or perhaps even tear through, causing severe gunnel damage. Smith backing plates distribute mounting bolt pressure evenly over 30 times more surface area than with standard washers alone. 2 sizes, one for 70 series and one for 80 series rod holders. Each size fits all 3 models of the series.Features: Use this backing plate for all 70 series rod holders (53670A, 53670CA, 53671A, 53671CA, 53672A, and 53672CA) 316L cast stainless steel 4" x 5-1/4" 4mm thick Use your 1/4" stainless bolts and nuts (hardware not included)

Read more less

70 Series Standard Flush Mount Rod Holder - 0 Degree - Stainless Steel - Cast Bottom - Black LinerThese flush mount rod holders are made of 316L stainless steel and have a wide, low-profile cap that improves the look of any boat and provides outstanding mounting strength. This model has a durable, rounded cast bottom with a hole to drain water. Features: 316L stainless steel Fits 2-3/16 in. hole diameter Cast models feature a 1/2 in. drain hole No logo on the cap for a sleek low profile The liner runs the full length of the tube Specifications: Degrees: 0 degrees Bottom Style: Cast Liner Color: Black Inner Diameter: 1-5/8 in. Cap Size: 4-1/2 in. long x 3-5/8 in. wide Tube Length: 9 in. Specifications: Angle: 0 Degrees Construction: Stainless Steel Box Dimensions: 5"H x 5"W x 14"L WT: 1.95 lbs Quick Guide (pdf)

Read more less

80 Series Screwless Flush Mount Rod Holder - 15 Degree - Stainless Steel - Swivel Bottom - Black LinerThese flush mount rod holders are made of 316L stainless steel and have a wide, low-profile cap that improves the look of any boat and provides outstanding mounting strength.Features: 316L stainless steel Fits 2-9/16 in. hole diameter No logo on the cap for a sleek low profile The liner runs the full length of the tube Includes a backing plate and installation nut Installation requires Model # 53679 Installation Socket Specifications: Degrees: 15 degrees Bottom Style: Swivel Liner Color: Black Inner Diameter: 1-7/8 in. Outer Diameter: 2-5/8 in. Cap Size: 5-1/8 in. long x 4-1/4 in. wide Tube Length: 10 in. Specifications: Angle: 15 Degrees Construction: Stainless Steel Box Dimensions: 5"H x 5"W x 15"L WT: 5.5 lbs UPC: 768296011048 Quick Guide (pdf)

Read more less

80 Series Screwless Flush Mount Rod Holder - 0 Degree - Stainless Steel - Swivel Bottom - Black LinerThese flush mount rod holders are made of 316L stainless steel and have a wide, low-profile cap that improves the look of any boat and provides outstanding mounting strength.Features: 316L stainless steel Fits 2-9/16 in. hole diameter No logo on the cap for a sleek low profile The liner runs the full length of the tube Includes a backing plate and installation nut Installation requires Model # 53679 Installation Socket Specifications: Degrees: 0 degrees Bottom Style: Swivel Liner Color: Black Inner Diameter: 1-7/8 in. Outer Diameter: 2-5/8 in. Cap Size: 5-1/8 in. long x 4-1/4 in. wide Tube Length: 10 in. Specifications: Angle: 0 Degrees Construction: Stainless Steel Box Dimensions: 5"H x 5"W x 15"L WT: 5.5 lbs UPC: 768296011031 Quick Guide (pdf)

Read more less

80 Series Screwless Flush Mount Rod Holder - 30 Degree - Stainless Steel - Cast Bottom - Black LinerThese flush mount rod holders are made of 316L stainless steel and have a wide, low-profile cap that improves the look of any boat and provides outstanding mounting strength.Features: 316L stainless steel Fits 2-9/16 in. hole diameter Cast models feature a ½ in. drain hole No logo on the cap for a sleek low profile The liner runs the full length of the tube Includes a backing plate and installation nut Installation requires Model # 53679 Installation Socket Specifications: Degrees: 30 degrees Bottom Style: Cast Liner Color: Black Inner Diameter: 1-7/8 in. Outer Diameter: 2-5/8 in. Cap Size: 5-1/8 in. long x 4-1/4 in. wide Tube Length: 10 in. Specifications: Angle: 30 Degrees Construction: Stainless Steel Box Dimensions: 5"H x 5"W x 15"L WT: 5.5 lbs UPC: 768296011109 Quick Guide (pdf)

Read more less

80 Series Screwless Flush Mount Rod Holder - 15 Degree - Stainless Steel - Cast Bottom - Black LinerThese flush mount rod holders are made of 316L stainless steel and have a wide, low-profile cap that improves the look of any boat and provides outstanding mounting strength.Features: 316L stainless steel Fits 2-9/16 in. hole diameter Cast models feature a ½ in. drain hole No logo on the cap for a sleek low profile The liner runs the full length of the tube Includes a backing plate and installation nut Installation requires Model # 53679 Installation Socket Specifications: Degrees: 15 degrees Bottom Style: Cast Liner Color: Black Inner Diameter: 1-7/8 in. Outer Diameter: 2-5/8 in. Cap Size: 5-1/8 in. long x 4-1/4 in. wide Tube Length: 10 in. Specifications: Angle: 15 Degrees Construction: Stainless Steel Box Dimensions: 5"H x 5"W x 13"L WT: 4 lbs UPC: 768296010843 Quick Guide (pdf)

Read more less

80 Series Screwless Flush Mount Rod Holder - 0 Degree - Stainless Steel - Cast Bottom - Black LinerThese flush mount rod holders are made of 316L stainless steel and have a wide, low-profile cap that improves the look of any boat and provides outstanding mounting strength.Features: 316L stainless steel Fits 2-9/16 in. hole diameter Cast models feature a ½ in. drain hole No logo on the cap for a sleek low profile The liner runs the full length of the tube Includes a backing plate and installation nut Installation requires Model # 53679 Installation Socket Specifications: Degrees: 0 degrees Bottom Style: Cast Liner Color: Black Inner Diameter: 1-7/8 in. Outer Diameter: 2-5/8 in. Cap Size: 5-1/8 in. long x 4-1/4 in. wide Tube Length: 10 in. Specifications: Angle: 0 Degrees Construction: Stainless Steel Box Dimensions: 5"H x 5"W x 15"L WT: 5.5 lbs UPC: 768296010836 Quick Guide (pdf)

Read more less

70 Series Screwless Flush Mount Rod Holder - 30 Degree - Stainless Steel - Cast Bottom - Black Liner - BoxedThese flush mount rod holders are made of 316L stainless steel and have a wide, low-profile cap that improves the look of any boat and provides outstanding mounting strength.Features: 316L stainless steel Fits 2-3/16 in. hole diameter Cast models feature a ½ in. drain hole No logo on the cap for a sleek low profile The liner runs the full length of the tube Includes a backing plate and installation nut Installation requires Model # 53679 Installation Socket Specifications: Degrees: 30 degrees Bottom Style: Cast Liner Color: Black Inner Diameter: 1-5/8 in. Outer Diameter: 2-1/8 in. Cap Size: 4-1/2 in. long x 3-5/8 in. wide Tube Length: 9 in. Specifications: Angle: 30 Degrees Construction: Stainless Steel Box Dimensions: 5"H x 5"W x 15"L WT: 5.5 lbs UPC: 768296010331 Quick Guide (pdf)

Read more less

70 Series Screwless Flush Mount Rod Holder - 15 Degree - Stainless Steel - Cast Bottom - Black Liner - BoxedThese flush mount rod holders are made of 316L stainless steel and have a wide, low-profile cap that improves the look of any boat and provides outstanding mounting strength.Features: 316L stainless steel Fits 2-3/16 in. hole diameter Cast models feature a ½ in. drain hole No logo on the cap for a sleek low profile The liner runs the full length of the tube Includes a backing plate and installation nut Installation requires Model # 53679 Installation Socket Specifications: Degrees: 15 degrees Bottom Style: Cast Liner Color: Black Inner Diameter: 1-5/8 in. Outer Diameter: 2-1/8 in. Cap Size: 4-1/2 in. long x 3-5/8 in. wide Tube Length: 9 in. Specifications: Angle: 15 Degrees Construction: Stainless Steel Box Dimensions: 5"H x 5"W x 11"L WT: 4 lbs UPC: 768296010324 Quick Guide (pdf)

Read more less

70 Series Screwless Flush Mount Rod Holder - 0 Degree - Stainless Steel - Cast Bottom - Black Liner - BoxedThese flush mount rod holders are made of 316L stainless steel and have a wide, low-profile cap that improves the look of any boat and provides outstanding mounting strength.Features: 316L stainless steel Fits 2-3/16 in. hole diameter Cast models feature a ½ in. drain hole No logo on the cap for a sleek low profile The liner runs the full length of the tube Includes a backing plate and installation nut Installation requires Model # 53679 Installation Socket Specifications: Degrees: 0 degrees Bottom Style: Cast Liner Color: Black Inner Diameter: 1-5/8 in. Outer Diameter: 2-1/8 in. Cap Size: 4-1/2 in. long x 3-5/8 in. wide Tube Length: 9 in. Specifications: Angle: 0 Degrees Construction: Stainless Steel Box Dimensions: 5"H x 5"W x 11"L WT: 4 lbs UPC: 768296010317 Quick Guide (pdf)

Read more less

Flush Mount 30° Nylon Rod Holder - White Corrosion-free nylon rod holder. These 30° light-duty fishing rod holders are an economical way to add more rod storage. Molded in one piece from UV-resistant Nylon, these rod holders are tough and corrosion-free. 10" tube. Cap is 4" long x 3-1/2" wide. Installs into a 2-1/16" hole. Mount with 3/16" screws (not included).

Read more less

Trailer Tongue Step PadThe Trailer Tongue Step Pad makes accessing your boat easy by providing a stable and steady place to anchor your feet. It can be mounted anywhere that is suitable, such as on trailer tongues or side rails.Features: Fits any 2x3 in. or 3x3 in. rail Mounting hardware is included Measures 24 in. length and 9 in. wide Has a textured surface for slip resistance *Sold individually

Read more less

8"-5/8" Keel Roller Black Natural RubberBlack natural rubber rollers are original equipment on many trailers. Fits standard brackets and shaft sizes.Features: Black natural rubber 3-3/8" Diameter 7-7/8" wide 5/8" shaft

Read more less

Zinc U-Bolt 7/16"-14 X 3-1/8" X 3" with Washers & Nuts - SquareZinc-plated u-bolt for mounting brackets & accessories to trailer frames.Features: Square bend Grade 5 7/16"-14 diameter/thread 3-1/8" W x 3" L *Comes packaged with nuts and washers.

Read more less

Zinc U-Bolt 7/16"-14 X 3-1/8" X 4" with Washers & Nuts - SquareZinc-plated u-bolt for mounting brackets & accessories to trailer frames.Features: Square bend Grade 5 7/16"-14 diameter/thread 3-1/8" W x 4" L *Comes packaged with nuts and washers.

Read more less

Roller Shaft 5/8" x 13" with Cap NutsReplacement Roller shaft and cap nuts.Features: 5/8" diameter x 13" long Zinc Plated Comes with two 5/8" cap nuts

Read more less

Swivel Bracket Assembly - 8" BracketThis Smith adjustable bracket is designed to support bunk boards. Hot dip galvanizing for years of use in the harsh marine environment.This bracket assembly uses bolster bracket-10100G and swivel bracket-10200G.Features: Bolster bracket: 8" bracket, 11 gauge material, 2-1/2" wide, slots 1/2" wide, swivel hole 1/2" dia., slots 2-3/4" Swivel bracket: 11 gauge material, bunk flange 1-3/8" x 3-1/2", bunk flange holes 3/8" dia., swivel flange 2" tall x 3-1/2", swivel flange hole 1/2" dia., hole centers 2-1/2" Overall assembly length is 9"

Read more less

Bow Roller - Black - 3" Diameter - 3-1/8"W - 1/2" IDBlack natural rubber rollers are original equipment on many trailers. Fits standard brackets and shaft sizes.Features: Black natural rubber 3" Diameter 3-1/8" wide 1/2" shaft

Read more less