Centaur Charger - 30AMP, 12/30(3), 120-240VThe Centaur range of battery chargers features auto-ranging input covering 90-265VAC 50/60Hz input meaning they can be used anywhere in the world.Crucially, and unlike many other products that state universal input, the Centaur range will maintain full output power within the entire specified range. Other features include fully automatic three stage charge characteristic that ensures batteries are fully charged every time and three isolated charge outputs for multi battery configurations to suit the majority of typical installations.The range spans 12V and 24V models from 16A through to 100A.Warranty InfoWARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.Please contact your dealer for any returns, repairs or support issues related to this product. Specifications: Portable: No Charging Banks: 3 Charger Output Voltage: 12v Charger Output - Amps: 30a Charger Input - Voltage: 120/240v Box Dimensions: 8"H x 12"W x 18"L WT: 10.65 lbs UPC: 8719076021483 Quick Guide (pdf)Owner's Manual (pdf)Brochure (pdf)

Read more less

Centaur Charger - 12 VDC - 60AMP - 3-Bank - 120-240 VACFeatures: Quality without compromise -  Aluminium epoxy powder coated cases with drip shield and stainless steel fixings withstand the rigors of an adverse environment: heat, humidity and salt air. Circuit boards are protected with an acrylic coating for maximum corrosion resistance. Temperature sensors ensure that power components will always operate within specified limits, if needed by automatic reduction of output current under extreme environmental conditions. Universal 90-265V AC input voltage range and also suitable for DC supply (AC-DC and DC-DC operation) All models will operate without any adjustment needed over a 90 to 265 Volt input voltage range, whether 50 Hz or 60 Hz.  The chargers also accept a 90-400 V DC supply.  Three outputs that each can supply the full output current Three isolated outputs to simultaneously charge 3 battery banks Each output is capable to supply the full rated current.  Three-stage charging, with temperature compensation The Centaur charges at bulk rate until the output has reduced to 70% of the rated Amps, at which a 4 hour timer begins. After the timed period the charger switches to float rate. An internal temperature sensor is used to compensate the charge voltage with – 2 mV/ºC (– 1 mV/ºF) per cell. A DIP switch is available to select the optimum charge/float voltages for Flooded Lead-acid, Gel or AGM batteries Warranty InfoWARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.Please contact your dealer for any returns, repairs or support issues related to this product. Specifications: Portable: No Charging Banks: 3 Charger Output Voltage: 12v Charger Input - Voltage: 120/240v Charger Output - Amps: 60a Box Dimensions: 8"H x 13"W x 21"L WT: 15.4 lbs UPC: 8719076021513 Quick Guide (pdf)Owner's Manual (pdf)Brochure (pdf)

Read more less

C-CHARGER 5000 Series Marine Electronic Battery Chargers are the best choice for high-performance Marine UL listed products. Utilizing high-quality components and corrosion-resistant, anodized aluminum housing, this battery charger is built to last, performing in the toughest of marine environments. Features a battery type selector switch which allows the boater to charge either lead acid, gel, or AGM batteries.Marine UL listing ensures durability and safety• Only complete line of battery chargers approved by Marine UL's stringent specifications, testing, and evaluation• Tested for durability against static, impact, vibration, and shock• Ignition protected (USCG-33 CFR 183.410)• AC and DC fuse protectionMulti-step charging with temperature compensation• Restores up to 3 individual battery banks simultaneously• Internal temperature compensation (12V 30-100 amp models and 24V 20-60 amp models) automatically adjusts output to precisely charge batteries according to ambient conditionsCorrosion resistant housing and components• Constructed of tough, anodized aluminum housing that stands up to the elements, including extreme heat, humidity, and salt air• Circuit boards with UL recommended coatings provide the ultimate in environmental protection and hydrolyte stability• Meets requirements of MIL-1-46058CCool and quiet operation• Cooling fan only operates during peak current demands• Virtually no RFI or EMI interference exceeds FCC/Class B requirementsEasy to install and service• Battery selector switch allows charger to be used with lead acid, gel, or AGM batteries• Exterior slots for easy mounting• Easy access to terminal connections and fuses Replaced by Charles Recommended Direct Replacement Centaur 12v/30Amp/3Bank

Read more less

Centaur Charger - 50AMP, 12/50(3), 120-240VThe Centaur range of battery chargers features auto-ranging input covering 90-265VAC 50/60Hz input meaning they can be used anywhere in the world.Crucially, and unlike many other products that state universal input, the Centaur range will maintain full output power within the entire specified range. Other features include fully automatic three stage charge characteristic that ensures batteries are fully charged every time and three isolated charge outputs for multi battery configurations to suit the majority of typical installations.The range spans 12V and 24V models from 16A through to 100A.Warranty InfoWARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.Please contact your dealer for any returns, repairs or support issues related to this product. Specifications: Charging Banks: 3 Charger Output Voltage: 12v Charger Output - Amps: 50a Charger Input - Voltage: 120/240v Portable: No Box Dimensions: 9"H x 14"W x 22"L WT: 15.95 lbs UPC: 8719076021506 Quick Guide (pdf)Owner's Manual (pdf)Brochure (pdf)

Read more less

Picture of 50 amp shown C-CHARGER 5000 Series Marine Electronic Battery Chargers are the best choice for high-performance Marine UL listed products. Utilizing high-quality components and corrosion-resistant, anodized aluminum housing, this battery charger is built to last, performing in the toughest of marine environments. Features a battery type selector switch which allows the boater to charge either lead acid, gel, or AGM batteries.Marine UL listing ensures durability and safety• Only complete line of battery chargers approved by Marine UL's stringent specifications, testing, and evaluation• Tested for durability against static, impact, vibration, and shock• Ignition protected (USCG-33 CFR 183.410)• AC and DC fuse protectionMulti-step charging with temperature compensation• Restores up to 3 individual battery banks simultaneously• Internal temperature compensation (12V 30-100 amp models and 24V 20-60 amp models) automatically adjusts output to precisely charge batteries according to ambient conditionsCorrosion resistant housing and components• Constructed of tough, anodized aluminum housing that stands up to the elements, including extreme heat, humidity, and salt air• Circuit boards with UL recommended coatings provide the ultimate in environmental protection and hydrolyte stability• Meets requirements of MIL-1-46058CCool and quiet operation• Cooling fan only operates during peak current demands• Virtually no RFI or EMI interference exceeds FCC/Class B requirementsEasy to install and service• Battery selector switch allows charger to be used with lead acid, gel, or AGM batteries• Exterior slots for easy mounting• Easy access to terminal connections and fuses Replaced by Charles Recommended Direct Replacement Centaur 12v/60Amp/3Bank

Read more less

C-CHARGER 5000 Series Marine Electronic Battery Chargers are the best choice for high-performance Marine UL listed products. Utilizing high-quality components and corrosion-resistant, anodized aluminum housing, this battery charger is built to last, performing in the toughest of marine environments. Features a battery type selector switch which allows the boater to charge either lead acid, gel, or AGM batteries.Marine UL listing ensures durability and safety• Only complete line of battery chargers approved by Marine UL's stringent specifications, testing, and evaluation• Tested for durability against static, impact, vibration, and shock• Ignition protected (USCG-33 CFR 183.410)• AC and DC fuse protectionMulti-step charging with temperature compensation• Restores up to 3 individual battery banks simultaneously• Internal temperature compensation (12V 30-100 amp models and 24V 20-60 amp models) automatically adjusts output to precisely charge batteries according to ambient conditionsCorrosion resistant housing and components• Constructed of tough, anodized aluminum housing that stands up to the elements, including extreme heat, humidity, and salt air• Circuit boards with UL recommended coatings provide the ultimate in environmental protection and hydrolyte stability• Meets requirements of MIL-1-46058CCool and quiet operation• Cooling fan only operates during peak current demands• Virtually no RFI or EMI interference exceeds FCC/Class B requirementsEasy to install and service• Battery selector switch allows charger to be used with lead acid, gel, or AGM batteries• Exterior slots for easy mounting• Easy access to terminal connections and fuses Replaced by Charles Recommended Direct Replacement Centaur 12v/40Amp/3Bank

Read more less

C-CHARGER 5000 Series Marine Electronic Battery Chargers are the best choice for high-performance Marine UL listed products. Utilizing high-quality components and corrosion-resistant, anodized aluminum housing, this battery charger is built to last, performing in the toughest of marine environments. Features a battery type selector switch which allows the boater to charge either lead acid, gel, or AGM batteries.Marine UL listing ensures durability and safety• Only complete line of battery chargers approved by Marine UL's stringent specifications, testing, and evaluation• Tested for durability against static, impact, vibration, and shock• Ignition protected (USCG-33 CFR 183.410)• AC and DC fuse protectionMulti-step charging with temperature compensation• Restores up to 3 individual battery banks simultaneously• Internal temperature compensation (12V 30-100 amp models and 24V 20-60 amp models) automatically adjusts output to precisely charge batteries according to ambient conditionsCorrosion resistant housing and components• Constructed of tough, anodized aluminum housing that stands up to the elements, including extreme heat, humidity, and salt air• Circuit boards with UL recommended coatings provide the ultimate in environmental protection and hydrolyte stability• Meets requirements of MIL-1-46058CCool and quiet operation• Cooling fan only operates during peak current demands• Virtually no RFI or EMI interference exceeds FCC/Class B requirementsEasy to install and service• Battery selector switch allows charger to be used with lead acid, gel, or AGM batteries• Exterior slots for easy mounting• Easy access to terminal connections and fuses Replaced by Charles Recommended Direct Replacement Centaur 12v/50Amp/3Bank

Read more less

Centaur Charger - 12 VDC - 40AMP - 3-Bank - 120-240 VACFeatures: Quality without compromise -  Aluminium epoxy powder coated cases with drip shield and stainless steel fixings withstand the rigors of an adverse environment: heat, humidity and salt air. Circuit boards are protected with an acrylic coating for maximum corrosion resistance. Temperature sensors ensure that power components will always operate within specified limits, if needed by automatic reduction of output current under extreme environmental conditions. Universal 90-265V AC input voltage range and also suitable for DC supply (AC-DC and DC-DC operation) All models will operate without any adjustment needed over a 90 to 265 Volt input voltage range, whether 50 Hz or 60 Hz.  The chargers also accept a 90-400 V DC supply.  Three outputs that each can supply the full output current Three isolated outputs to simultaneously charge 3 battery banks Each output is capable to supply the full rated current.  Three-stage charging, with temperature compensation The Centaur charges at bulk rate until the output has reduced to 70% of the rated Amps, at which a 4 hour timer begins. After the timed period the charger switches to float rate. An internal temperature sensor is used to compensate the charge voltage with – 2 mV/ºC (– 1 mV/ºF) per cell. A DIP switch is available to select the optimum charge/float voltages for Flooded Lead-acid, Gel or AGM batteries Warranty InfoWARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.Please contact your dealer for any returns, repairs or support issues related to this product. Specifications: Charger Input - Voltage: 120/240v Portable: No Charging Banks: 3 Charger Output Voltage: 12v Charger Output - Amps: 40a Box Dimensions: 8"H x 13"W x 22"L WT: 15.95 lbs UPC: 8719076021490 Quick Guide (pdf)Owner's Manual (pdf)Brochure (pdf)

Read more less

Centaur Charger - 12 VDC - 80AMP - 3-Bank - 120-240 VACFeatures: Quality without compromise -  Aluminium epoxy powder coated cases with drip shield and stainless steel fixings withstand the rigors of an adverse environment: heat, humidity and salt air. Circuit boards are protected with an acrylic coating for maximum corrosion resistance. Temperature sensors ensure that power components will always operate within specified limits, if needed by automatic reduction of output current under extreme environmental conditions. Universal 90-265V AC input voltage range and also suitable for DC supply (AC-DC and DC-DC operation) All models will operate without any adjustment needed over a 90 to 265 Volt input voltage range, whether 50 Hz or 60 Hz.  The chargers also accept a 90-400 V DC supply.  Three outputs that each can supply the full output current Three isolated outputs to simultaneously charge 3 battery banks Each output is capable to supply the full rated current.  Three-stage charging, with temperature compensation The Centaur charges at bulk rate until the output has reduced to 70% of the rated Amps, at which a 4 hour timer begins. After the timed period the charger switches to float rate. An internal temperature sensor is used to compensate the charge voltage with – 2 mV/ºC (– 1 mV/ºF) per cell. A DIP switch is available to select the optimum charge/float voltages for Flooded Lead-acid, Gel or AGM batteries Warranty InfoWARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.Please contact your dealer for any returns, repairs or support issues related to this product. Specifications: Charger Output - Amps: 80a Portable: No Charger Input - Voltage: 120/240v Charger Output Voltage: 12v Charging Banks: 3 Box Dimensions: 9"H x 14"W x 25"L WT: 24.25 lbs UPC: 8719076021520 Quick Guide (pdf)Owner's Manual (pdf)Brochure (pdf)

Read more less

2026 Model  Centaur Charger - 24 VDC - 60AMP - 3-Bank - 120-240 VAC Features: Quality without compromise -  Aluminium epoxy powder coated cases with drip shield and stainless steel fixings withstand the rigors of an adverse environment: heat, humidity and salt air. Circuit boards are protected with an acrylic coating for maximum corrosion resistance. Temperature sensors ensure that power components will always operate within specified limits, if needed by automatic reduction of output current under extreme environmental conditions. Universal 90-265V AC input voltage range and also suitable for DC supply (AC-DC and DC-DC operation) All models will operate without any adjustment needed over a 90 to 265 Volt input voltage range, whether 50 Hz or 60 Hz.  The chargers also accept a 90-400 V DC supply.  Three outputs that each can supply the full output current Three isolated outputs to simultaneously charge 3 battery banks Each output is capable to supply the full rated current.  Three-stage charging, with temperature compensation The Centaur charges at bulk rate until the output has reduced to 70% of the rated Amps, at which a 4 hour timer begins. After the timed period the charger switches to float rate. An internal temperature sensor is used to compensate the charge voltage with – 2 mV/ºC (– 1 mV/ºF) per cell. A DIP switch is available to select the optimum charge/float voltages for Flooded Lead-acid, Gel or AGM batteries Warranty Info WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Please contact your dealer for any returns, repairs or support issues related to this product. Specifications: Portable: No Charger Output Voltage: 24v Charger Output - Amps: 60a Charger Input - Voltage: 120/240v Charging Banks: 3 Box Dimensions: 9"H x 14"W x 25"L WT: 22.05 lbs UPC: 8719076021575 Quick Guide (pdf)Owner's Manual (pdf)Brochure (pdf)

Read more less

C-CHARGER 5000 Series Marine Electronic Battery Chargers are the best choice for high-performance Marine UL listed products. Utilizing high-quality components and corrosion-resistant, anodized aluminum housing, this battery charger is built to last, performing in the toughest of marine environments. Features a battery type selector switch which allows the boater to charge either lead acid, gel, or AGM batteries.Marine UL listing ensures durability and safety• Only complete line of battery chargers approved by Marine UL's stringent specifications, testing, and evaluation• Tested for durability against static, impact, vibration, and shock• Ignition protected (USCG-33 CFR 183.410)• AC and DC fuse protectionMulti-step charging with temperature compensation• Restores up to 3 individual battery banks simultaneously• Internal temperature compensation (12V 30-100 amp models and 24V 20-60 amp models) automatically adjusts output to precisely charge batteries according to ambient conditionsCorrosion resistant housing and components• Constructed of tough, anodized aluminum housing that stands up to the elements, including extreme heat, humidity, and salt air• Circuit boards with UL recommended coatings provide the ultimate in environmental protection and hydrolyte stability• Meets requirements of MIL-1-46058CCool and quiet operation• Cooling fan only operates during peak current demands• Virtually no RFI or EMI interference exceeds FCC/Class B requirementsEasy to install and service• Battery selector switch allows charger to be used with lead acid, gel, or AGM batteries• Exterior slots for easy mounting• Easy access to terminal connections and fuses Replaced by Charles Recommended Direct Replacement Centaur 12v/80Amp/3Bank

Read more less

XD Series Single 500 Amp Heavy Duty Battery Switch/Mechanical ContactorFeatures: Silver Alloy Contact Points support high ampere/full voltage switching capability versus legacy rotary style switches. Expandable: Integrate the 8700 XD Battery Disconnect easily with XD Series FLEX/ACR/LVD relays via using optional 8790 Link and 8791 Cross Link Busbars bars for easy integration with other Single, Dual or Triple Circuit XD relays. Terminal Stud Protection: Included protective cover with convenient label recesses ensures no accidental shorts occur and allows for easy identification of circuits long term. Bullet-proof Construction: Sealed to IP67/IP6K9K, high-temperature electronics and materials allow mounting anywhere. Stainless steel cable lug studs. Large mounting holes accept 1/4-20 / M6 attachment hardware.  Intuitive Manual Control: Bright yellow knob and intuitively easy-to-read on/off label simplifies operation and awareness of the state of manual override and whether the device is being left in a locked off or locked on state. Ignition Protected: Safe for installation in gasoline-powered boats and other combustible install environments. Sealed IP67 Construction keeps moisture out and the integrated Gore-Tex pressure regulation vent increases its ability to operate reliably for long-term harsh environment operation.  Compact Case Design allows for easy surface mount or rear panel installs and rectangular shape (narrower than competing products) keeps finding a mounting location easy. Specifications: Total Continuous Current Amps: 500 Max Cranking Current (Amps): 1500 Terminal Stud Size (mm): M10 Voltage Range (VDC): 8-36 Ingress Protection: IP67/IP6K 9K Contact Materials: Silver Alloy Focal Features:High Visibility KnobForce each individual relay Open or Closed and optionally leave knob in either position to lock relay in either condition. 40 Circuit Label Sheet IncludedConvenient recesses for included weatherproof label set makes circuit and relay identification easy. Blank labels for custom applications.Protective Cover IncludedProtects terminal studs and cable terminal edges from inadvertent shorts to each other or ground.Stainless HardwareCorrosion is no issue with quality stainless steel studs and self locking flanged nuts.Smaller FootprintXD Relays offers high Amp rating in a smaller package than competitive solutions, reducing install space requirements to a minimum.Integrated VentHigh quality Gortex vent regulates internal device pressure to eliminate moisture entry across seals and ensure long product life in harsh environments. Brochure (pdf)

Read more less

Battery ChargerAttwood's Battery Charger is compact and perfect for your bench, garage or shop use. Overcharge, short circuit and reverse polarity protection provides years of worry free use. Provides 2 and 6 amp charge for 12V batteries. 6 amp charge for 6V batteries. Automatically switches to trickle charge mode after battery is fully charged. Dual rated 12 and 6 volt battery charger can be used for all of your marine, automotive, RV and sports applications. LED indicator - power on Ammeter indicates charging current 6 foot power cord length 48 inch battery connector leads WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Charger Output - Amps: 2/6a Charging Banks: 1 Portable: Yes Charger Input - Voltage: 120v Charger Output Voltage: 12v Box Dimensions: 6"H x 9"W x 9"L WT: 6.95 lbs UPC: 022697119018

Read more less

MK-315D 3 Bank x 5 AmpsON-BOARD MARINE BATTERY CHARGERSReengineered with a microprocessor-based design, digital on-board chargers protect your battery, charge faster, and help you stay on the water longer.DIGITALLY CONTROLLEDWe set out to build a smarter charger, and the result is the ingenious microprocessor-based design of onboard units. By monitoring factors like temperature and state of charge, they deliver a faster, more regulated, precise charge so you can stay on the water longer, without worrying about your batteries.PROTECTS BATTERIESOn-board chargers feature Multi-Stage Charging and Automatic Temperature Compensation for more precise charges that won't damage your battery. And its automatic shut-off feature extends battery life by shutting down when charging is complete. So your battery and your day on the water will always last longer.TWO TIMES FASTER CHARGINGIn high temperatures, on-board chargers juice up your batteries up to twice as fast. Thanks to a digital design that monitors everything from temperature to state of charge, on-board chargers get the job done.ENHANCED STATUS CODESComprehensive readings on chargers inform you of the charge stage, maintenance mode status, any error notifications, and full charge.Features: Waterproof, shock- and vibration-resistant aluminum construction Saltwater tested and fully corrosion-resistant Short circuit, reverse polarity, arc, and ignition protected For use with 12V/6 cell batteries that are flooded/wet cell, maintenance-free, or starved electrolyte (AGM) only FCC compliant UL listed to marine standard 1236 Length - 12-1/2" Width - 7-1/2" Height - 4" Weight - 14lbs WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Charger Output - Amps: 15a Charging Banks: 3 Portable: No Charger Input - Voltage: 120v Charger Output Voltage: 12/24/36v Box Dimensions: 7"H x 8"W x 16"L WT: 15.6 lbs UPC: 029402034796 Owner's Manual (pdf)Brochure (pdf)

Read more less

5022 Panel Mount AGC/MDL Fuse Holder Replacement CapReplaces cap for 5021 Specifications: Fuse Type: AGC/MDL Type: Fuse Holders Box Dimensions: 1"H x 2"W x 4"L WT: 0.05 lbs UPC: 632085050221

Read more less

Sealink® Dual USB-A/C Combo ChargerThe Marinco Sealink USB-A/C Combo offers total charging flexibility. Compatible with 12V and 24V systems, and delivering up to 45W of total output, the charger charges electronics including cell phones, tablets, headphones & other devices. Mounting in a standard 1 1/8“ hole and featuring electrical tabs for quick wiring, the charger is easy to install. A weather-resistant cover protects against water and dust ingress, making it ideal for challenging environments.Features: Two USB Ports: (1) USB-A and (1) USB-C Mounts in a 1 1/8” hole Water resistant cap LED power indicator Applications: Marine RV Automotive Golf Cars Specialty Vehicles Industrial Equipment Quick Guide (pdf)

Read more less

19mm Push Button Switch - Off/On/On Contact - Blue/Green/Red LED - 1' LeadThis stainless-steel plated metal button can transform any dash by adding a touch of modern flair. This button has an “Off/On/On" standard contact.The body design combined with the included gasket gives this button switch a waterproof rating of IP69K. At night, every switch is backlit with blue LED light for unparalleled visibility. That light changes to red to let users know that the function is on without question.Features:1 ft. leadSpecifications: Function: Off-On-On (standard contact) Off/On: Blue/green 2nd On: Red Rear Mark Page: Blue dot Switch Rating: 15A/12 – 24VDC   Material: Stainless steel Mechanical Life: 50,000 cycles     Electrical Life: 10,000 cycles Installation:Drill a 19mm hole into any material up to 6mm thick. Connect the 3 contacts for the button (color-coded for safety and convenience). Lastly, connect the 2 contacts for the LED. Specifications: Action: OFF/ON/ON Color: Blue/Green/Red Box Dimensions: 1"H x 1"W x 1"L WT: 0.61 lbs Quick Guide (pdf)Brochure (pdf)

Read more less

TILE USB-A/USB-C Interior Charging Socket - 12/24V - Black BezelTILE Series offers sleek, high-performance charging solutions designed specifically for marine interiors. These chargers blend seamlessly into luxury marine environments. Featuring a compact 40mm (1.57”) footprint and requiring just a 29mm (1.14”) hole saw for easy installation, the TILE Series combines functionality and style, making it the ideal choice for modernizing your vessel’s interior. Enhance your boat’s space with this practical, sophisticated solution for charging your everyday devices.Tile USB is FAST! It will charge at 36W on a 12V system or up to 60W on a 24V system. This makes it perfect for charging modern laptops and large tablets, phones, and any other USB-C-powered devices onboard.USB–C output60W max on 24V system, 36W max on 12V systemUniversalUniversal fit for any USB-C connectors. Fast charge (60W max) up to 2 devices at a time.Important informationTo maximize charge performance, use the cable supplied with your tablet, phone, etc. (C to C, or C-lightning) Phones charge at the same speed on either a 12 or 24V system, but a 24V system must be used to get the full 60W output suitable for laptops.WARNINGTILE USB products are designed for interior use only. Do not install in locations where water exposure is possible, as this may lead to product failure.Features: 12V & 24V  USB-A and USB-C Ultra-low profile Front fit Tiny footprint Available in 316 stainless steel or matte black Conformal coated electronics, protected against moisture Modernize your boat's interiors Specifications: Input Voltage Range: 10-32V DC (12/24V system) Input current max: Max 6A (10A fuse recommended)  Output (Type C): 12V System: 5V=3A, 9V=3A, 12V=3A Max, 24V System: 5V=3A, 9V=3A, 12V=3A, 15V=3A, 20V=3A Max Output (Type A): 12V System: 5V=3A, 9V=3A, 12V=3A Max, 24V System: 5V=3A, 9V=3A, 12V=3A, 15V=3A, 20V=3A Max Standby Power: 0.01W Certification: CE, FCC, UKCA, C-Tick, ROHS, WEE

Read more less

2300 150AMP Common BusBar 10 x #8-32 Screw Terminal with CoverFeatures: Stud design provides direct terminal to bus contact for low resistant connection Stainless steel studs and screws allow high torquing for excellent electrical contact Tin-plated copper bus for maximum conductivity and resistance to corrosion UL 94-VO rated (self extinguishing) base material resists high heat Press on insulating cover attaches to studs and allows unobstructed wire access Raised bus provides easy access to multiple wires on a single screw WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less

Fuse Holder ANL 300AProviding high-capacity fusing, fast response and very high interrupt ratings (ANL up to 6,000 Amps, Class-T up to 20,000 Amps), these fuse holders are ideal for protecting today's demanding onboard power electronics technology including inverters and battery chargers. They also protect wiring from short circuits. Pro Installer fuse holders' durable construction allow fuses to run at maximum load. Radiused ends improve cable routing options ANL: for use with 5/16" (8mm) or 3/8" (10mm) ANL fuses WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Fuse Type: ANL Type: Fuse Blocks Box Dimensions: 2"H x 6"W x 7"L WT: 0.4 lbs UPC: 843687006800 Brochure (pdf)

Read more less

Orion-TR Smart 12/12-30A (360W) Isolated DC-DC Charger or Power SupplyThe Orion-Tr Smart isolated DC-DC charger serves as a DC-DC battery charger or a power supply (also designed for use as a constant voltage source), offering a wide input and output voltage range. This is especially significant in the case of vehicles with a Euro 5 or Euro 6 smart alternator, which often supplies too low charging voltage even when the engine is running or when extended cable lengths, as is often the case in boats and RVs, lead to voltage drops. In such scenarios, precise and controlled charging is imperative to fully charge the service battery while protecting the starter/input battery from discharge.Bluetooth Smart Enabled Any Bluetooth-enabled smartphone, tablet, or other device can be used to monitor, change settings, and update the charger when new software features become available Instant Readout: The VictronConnect App can display key data, including warnings and alarms, on the device list page without the need to connect to the product Fully programmable Battery charge algorithm (configurable) or fixed output.  Smart Alternator Compatibility: engine running detection mechanism Adaptive 3-Stage Charge Algorithm: Bulk – Absorption – Float For lead-acid batteries, it is important that during shallow discharges the absorption time is kept short to prevent overcharging of the battery. After a deep discharge, the absorption time is automatically increased to make sure that the battery is completely recharged For lithium batteries, the absorption time is fixed; the default is 2 hours Alternatively, a fixed output voltage can be chosen Suitable for Use in Vehicles with a Smart Alternator (Euro 5 and Euro 6 Engines)The built-in engine shutdown detection will stop the converter when the engine is not running. This prevents unwanted discharge of the starter battery (see manual for details).Remote On/OffA remote on/off switch or relay contact can be connected to a two-pole connector. Alternatively, the H terminal (right) of the two-pole connector can be switched to battery plus, or the L terminal (left) of the two-pole connector can be switched to battery minus (or the chassis of a vehicle, for example).All Models Are Short Circuit Proof and Can Be Paralleled to Increase Output CurrentAn unlimited number of units can be connected in parallel.High Temperature ProtectedThe output current will reduce at high ambient temperatures.IP43 ProtectionWhen installed with the screw terminals oriented downward.Screw TerminalsNo special tools are needed for installation. Input fuse (not replaceable) *Input fuse (not replaceable) Specifications: Input Voltage Range: 10-17 V Under Voltage Shut Down: 7 V Under Voltage Restart: 7.5 V Nominal Output Voltage: 12.2 V Output Voltage Adjust Range: 10-15 V Output Voltage Tolerance: +/- 0,2 V Output Noise: 2 mV rms Cont. Output Current at Nominal Output Voltage and 40 Degrees C: 30 A Maximum Output Current (10 S) at Nominal Output Voltage minus 20%: 40 A Short Circuit Output Current: 60 A Cont. Output Power at 25 Degrees C: 430 W Cont. Output Power at 40 Degrees C: 360 W Efficiency: 87 % No Load Input Current (2): < 80 mA  Standby Current: Less than 1A Can Be Used as Power Supply: Yes, output voltage can be set with Bluetooth  Galvanic Isolation: 200 VDC between input, output, and case  Operating Temperature Range -20 to +55 °C (derate 3 % per °C above 40 °C)  Humidity: Max. 95 % non-condensing  DC Connection: Screw terminals  Maximum Cable Cross-Section: 16 mm²  AWG6  Weight: 1,8 kg (3 lb)  Dimensions (H x W x D):130 x 186 x 70 mm  (5.1 x 7.3 x 2.8 inch)  Protection Category IP43 (electronic components), IP22 (connection area)  Safety Standards: EN 60950 Emission/Immunity Standards: EN 61000-6-3, EN 55014-1 / EN 61000-6-2, EN 61000-6-1, EN 55014-2 Automotive Directive Standards: ECE R10-5 WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.Please contact your dealer for any returns, repairs or support issues related to this product. Specifications: Charger Output - Amps: 30a Charger Input - Voltage: 12v Portable: No Charging Banks: 1 Charger Output Voltage: 12v Box Dimensions: 4"H x 6"W x 9"L WT: 4.45 lbs UPC: 8719076047698 Quick Guide (pdf)

Read more less

MEGA Fuse 100A/80V (Package of 5 Pieces)Victron Energy supplies a range of fuse holders and fuses to suit a wide range of installations, and the MEGA fuses are frequently used in Victron Energy DC distribution systems. This particular pack of ceramic Victron MEGA fuses contains FIVE 80 AMP fuses.Features:For 80V productsSpecifications: Max Current Rating: 100 AMP Max Voltage Rating: 80V

Read more less

PROsine Remote LCD PanelThis remote panel displays DC input voltage from the battery, DC input current (amps) drawn from the battery, power scale with inverter wattage output, and status/error display for shutdown conditions - overload, over-temperature, and over/under voltage. Comes with 25' (7.6M) cable.NOTE: This accessory is included with PROsine inverters.WARNING: This product can expose you to chemicals including Diisononyl Phthalate (DINP) which is known to the State of California to cause cancer, and Di-isodecyl Phthalate (DIDP) which is known to the State of California to cause reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less

Heart FDM-12-25 Remote Panel, Battery Status & Freedom Inverter/Charger Remote ControlProvides Valuable Inverter/Charger System Monitoring and ControlThe Freedom Remote Control Panel (part#84-2056-01) allows you to control your Freedom Combi, Freedom 458, and Freedom Marine Series Inverter/Charger system from any convenient location. It is easy to read, operate, and install, and all controls can be accessed directly from the front panel.Note: Not for Freedom HF or Freedom SW Series.Features: Independent invert and charge on/off controls Push button control of power sharing, equalizing, and battery set-up Multi-colored LED displays battery state of charge, fault conditions, AC input, DC voltage, and DC amperage LED warning indicators for low battery and overload warning Splash-resistant design Incoming AC breaker selection allows programmable power sharing Easy to install 25' Cable One-year warranty Note: The 24-volt models of Freedom Combi inverter/chargers require a different Freedom Remote the Freedom Remote - 24V SKU 82-0101-04WARNING: This product can expose you to chemicals including Diisononyl Phthalate (DINP) which is known to the State of California to cause cancer, and Di-isodecyl Phthalate (DIDP) which is known to the State of California to cause reproductive harm. For more information go to P65Warnings.ca.gov. Quick Guide (pdf)Owner's Manual (pdf)Brochure (pdf)

Read more less

Charge N Start 4120 4 Amp Battery Charger & 1200 Amp Jump StarterNever Face a Dead Battery Again: Introducing the Battery Tender® Charge N Start 4120Transform your battery maintenance experience with the innovative Battery Tender® Charge N Start 4120 – your ultimate 2-in-1 power solution. Engineered in the USA and backed by our 60-year legacy of battery expertise, this versatile device combines our advanced charging technology with reliable jump-starting power in one portable unit.Professional-Grade Power When You Need It MostWhether you're facing an emergency start or maintaining your vehicle's battery health, the Charge N Start 4120 delivers exceptional performance. With 1200A of instant jump-starting power, it easily handles up to 6.0L gas and 4.0L diesel engines. The integrated 12V/4 AMP smart charger utilizes our exclusive ISM (Infinite Sequential Monitoring) technology to optimize your battery's health and extend its lifespan.Auto-Switch FeatureAdvanced charging technology automatically switches between maintaining your vehicle's battery and the internal jump starter, ensuring both power sources are always charged and ready for use. No manual intervention needed – the Charge N Start 4120 intelligently manages both batteries for complete peace of mind.Smart Technology Meets SafetyEvery Charge N Start 4120 features our advanced microprocessor-controlled charging system that automatically detects your battery charge level and adjusts accordingly. Our proprietary Charge N Store™ technology monitors and maintains optimal float voltage during long-term storage, ensuring your battery stays ready for action.Multiple built-in safety features, including spark-proof connections, reverse polarity protection, and temperature compensation, provide peace of mind during every use.Designed for Real-World ConvenienceWe've thoughtfully engineered every aspect of the Charge N Start 4120 for maximum usability: Easy to see LED lights show charging status and battery health at a glance Built-in LED emergency light for nighttime visibility Heavy-duty smart clamps with copper-plated jaws ensure superior connectivity Compact, portable design fits easily in your vehicle Premium storage case included for protection and organization  Versatile CompatibilityFrom weekend warriors to professional mechanics, the Charge N Start 4120 is designed to handle diverse vehicle applications: Automotive: Cars, SUVs, and light trucks Power Sports: Motorcycles, ATVs, and UTVs Marine: Personal watercraft and boats Emergency: Reliable backup power when you need it most  The Smart Choice for Complete Battery CareThe Charge N Start 4120 represents the next evolution in battery maintenance technology. By combining jump-starting capabilities with our industry-leading charging technology, you get professional-grade battery care in one convenient device.Whether you're maintaining a single vehicle or managing an entire fleet, the Charge N Start 4120 delivers the performance, reliability, and safety features you expect from Battery Tender.Don't let battery issues slow you down. Experience the peace of mind that comes with having America's most trusted battery care solution at your fingertips. The Battery Tender® Charge N Start 4120 – because your adventures shouldn't wait for a dead battery.Specifications: Charges & Maintains: Lawnmowers, Motorcycles, ATVs, Personal Watercraft Battery Compatibility: AGM, GEL, Lithium, Standard (Sealed or Flooded Lead Acid) Reach: Over 14 Ft Total Reach, AC Power Cord Length: 6 ft - 18 AWG, Charger Length: 0.72 ft, DC Output Cord Length: 6 ft - 18 AWG, DC Accessory Length: 2 ft - 16 AWG Output: 12V @ 4 AMP Charging, 12V 1200 AMP Jump Starting Input: 120V AC Warranty: 1 Year Specifications: Charger Input - Voltage: 120v Charger Output - Amps: 4a Charger Output Voltage: 12v Charging Banks: 1 Portable: Yes Box Dimensions: 6"H x 7"W x 10"L WT: 4.32 lbs UPC: 734357370201 Owner's Manual (pdf)Brochure (pdf)

Read more less

Freedom 458 Inverter/Charger - 2000W120 Vac / 60 HzWith filtered modified sine wave output, the Freedom 458 inverter/charger has the ability to run electrical equipment, appliances and even sensitive electronics. Perfect for any RV, the temperature controlled multistage charging ensures that your batteries are recharged quickly, and safety features such as automatic shut down protects your expensive deep-cycle batteries from excessive depletion.AC Power Inverter with High Surge Capability, 3-Stage ChargerWith filtered modified sine wave output, Freedom inverter/chargers run virtually anything, from electrical equipment to appliances and electronics in your RV. Temperature controlled multistage charging ensures that your batteries are recharged quickly, and automatic shutdown and other safety features protect your expensive deep-cycle batteries from excessive depletion.For inverter/charger control and basic system monitoring, use the Freedom Basic Remote. For advanced battery monitoring and remote control, Freedom 458 systems can be paired with optional Link instrumentation.Product Features: MSW AC power inverter with high surge capability Automatic 3-stage battery charger Temperature compensation with equalization stage provides optimal charging of deep cycle batteries Built-in transfer switch automatically transfers between inverter power and incoming AC power Power sharing prevents source AC input circuit breaker from tripping Customized settings can be programmed with the Freedom Basic Remote or Link 1000 panels Includes battery temperature sensor 30 month warranty Hardwired AC Output (Single In/Single Out) Protection Features: Over voltage and under voltage protection Over-temperature protection Overload protection Short circuit protection WARNING: This product can expose you to chemicals including Diisononyl Phthalate (DINP) which is known to the State of California to cause cancer, and Di-isodecyl Phthalate (DIDP) which is known to the State of California to cause reproductive harm. For more information go to P65Warnings.ca.gov.This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns. Specifications: Charger Output Voltage: 12v Charger Output - Amps: 100a Inverter Output Voltage: 120v Inverter Input Voltage: 12v Charger Input - Voltage: 120v Inverter Cont. Output Wattage: 2000w Outlet Qty: None Charging Banks: 1 Box Dimensions: 12"H x 15"W x 19"L WT: 55 lbs UPC: 647912105630 Quick Guide (pdf)Owner's Manual (pdf)

Read more less

621 Series Alternator - Spindle Mount(Single Foot) - 100A - 12VFeatures: 100A 12V Spindle Mount (Single Foot) 1-2"  Single Deep Vee Pulley Isolated Ground 1″ Motorola-Style Mounting;  Typical for Westerbeke, Lehman, Hino & Pathfinder Engines 2″ Delco-Style Mounting;  Typical for Volvo Penta (Gas & Diesel), John Deere, Perkins, Mercruiser, Pleasurecraft, Crusader, Indmar, Marine Power & other GM-based Engines This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns. Owner's Manual (pdf)

Read more less

VE.Can RJ45 Terminator - Bag of 2This bag contains two VE.Can RJ45 terminators. The terminators are included with some other Victron products, for example, the CANUSB.Please contact your dealer for any returns, repairs or support issues related to this product. Specifications: Package Qty: Two Box Dimensions: 1"H x 1"W x 11"L WT: 0.1 lbs UPC: 8719076019923 Quick Guide (pdf)

Read more less

A-Series Toggle Double PolePN: 7232Poles: 2Color: BlackAmperage: 10AFeatures: Meets American Boat and Yacht Council (ABYC) standards UL 1077 recognized, TUV certified, CE marked for Europe and CSA certified for Canada The industry standard circuit breaker for Blue Sea Systems electrical panels Combines switching and circuit protection into a single device Used as AC Main circuit protection "Trip Free" design cannot be held "ON" during fault current condition WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Amperage: 10a Box Dimensions: 1"H x 3"W x 4"L WT: 0.2 lbs UPC: 632085072322

Read more less

EasyView 5Waterproof system monitor with daylight display and intuitive touch control.Controlling your Mastervolt system has never been easier. The EasyView 5 features a sharp, waterproof display which is clearly readable in daylight. Thanks to the color touch screen and multi-language menu, the display is a pleasure to operate. Easily customizable favorite pages show all relevant system information at a glance.Features Water proof, daylight readable color display Intuitive touch control Customizable favorite pages Log book for warnings and alarms Buzzer and Home button Easy mounting: Front mount, wall mount or retrofit MasterBus powered or MasterBus powering by 12 V DC input Easy updating through integrated USB ApplicationsThe EasyView 5 completes any MasterBus system. Applications include yachts, vehicles and stationary systems. Markets include marine, mobile (recreational & professional), infra-structure, offshore, off-grid and industrial markets.Specifications Display: 4.5 inch high contrast display with capacitive touch control. Resolution: 480x272 pixels, Color depth: 16 bits Languages: English, Dutch, German, Spanish, Italian, French, Finnish, Swedish, Norwegian, Danish IP degree: IP65 waterproof front Power supply: MasterBus powered or MasterBus powering through 12/24 V input Power Consumption: < 160 mW (idle mode) Alarm: Buzzer integrated Connections: 2 x MasterBus, USB, 12/24 V auto ranging input for optional external power Mounting: Front mount, wall mount and MasterView Easy retrofit Dimensions, HxWxD: 113 x 127 x 43 mm WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Owner's Manual (pdf)Brochure (pdf)

Read more less

19mm Push Button Switch - Off/(On) Momentary Contact - Blue/Red LED - 1' LeadThis stainless-steel plated metal button can transform any dash by adding a touch of modern flair. This button has an “Off/(On)" momentary contact.The body design combined with the included gasket gives this button switch a waterproof rating of IP69K. At night, every switch is backlit with blue LED light for unparalleled visibility. That light changes to red to let users know that the function is on without question.Features:1 ft. leadSpecifications: Function: Off-(On) (momentary contact) Off/On: Blue/red Rear Mark Page: Green dot Switch Rating: 15A/12 – 24VDC   Material: Stainless steel Mechanical Life: 50,000 cycles     Electrical Life: 10,000 cycles Installation:Drill a 19mm hole into any material up to 6mm thick. Connect the 3 contacts for the button (color-coded for safety and convenience). Lastly, connect the 2 contacts for the LED. Specifications: Action: OFF/(ON) Color: Blue/Red Box Dimensions: 1"H x 1"W x 1"L WT: 0.21 lbs Quick Guide (pdf)Brochure (pdf)

Read more less

Mini Battery Switch Key with Removable Knob - 32V & 100AThese Mini Battery Switches feature a removable knob for extra security. To remove, simply twist the cap to the OUT position and pull. Mini footprint makes it ideal for close quarters. The 422732-1 is rated at 100A continuous and 150A cranking amps. Installation is as easy as drilling a 1-1/8" hole for the 422732-1, inserting the socket body, tightening the locking nut, and connecting the wires. Features:  3 Switch positions: On, off, and out Constructed of machined brass and injection molded nylon Specifications: Switch Face Width: (inch) 1-1/8" Volts: 32 Amps: 100 Stud Diameter: (inch) 1/4" WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Continuous Amperage: 100 Positions: 3 Box Dimensions: 2"H x 4"W x 6"L WT: 0.2 lbs UPC: 035514432955

Read more less

TRUEcharge™3 40A 3 Bank Battery Charger - 12VTRUEcharge3 battery chargers lead the industry with a small footprint and ultra-compact design. In addition to meeting global safety and regulatory standards, they feature low electrical interference and efficient power factor-corrected multistage charging. The TRUEcharge3 Chargers can be mounted in multiple positions thanks to their inherent drip-proof design characteristics. Unlike its predecessors, TRUEcharge3 is lithium-ion battery compatible.Designed for recreational and commercial applications worldwide, TRUEcharge3 accepts 90–265 Vac, and 47–63 Hz, which makes traveling abroad and handling poor-quality power a breeze. The easy-to-read display of the TRUEcharge3 12 V models can be enhanced with an optional remote panel. Each model has built-in protection against surges and spikes on the AC power line.Features: Microprocessor-controlled, multistage charging algorithms Settings for two and three-stage charging Battery-equalization feature Settings for flooded, gel, AGM, or lithium-ion batteries Equipped with parallel stacking (remote panel required) Ability to charge batteries drained to extremely low voltage Added quiet mode Protection Features: Reverse-battery polarity protection Drip-proof design DC over-voltage protection Over-temperature protection Circuit breaker protection Three-Stage ChargingMultistage charging ensures batteries receive optimum charging, but with minimal wear and tear, regulating the voltage and current delivered to the batteries in three automatic stages: Bulk: Replaces 70–80% of the battery’s state-of-charge at the fastest possible rate Absorption: Replenishes the remaining 20–30% of charge, bringing the battery to a full charge at a slow, safe rate Float: Voltage is reduced and held constant to prevent damage and maintain batteries at a full charge for the remaining 20–30% of charge, bringing the battery to a full charge at a slow, safe rate Power Factor Corrected (PFC) ChargingLess shore power is required for charging batteries, freeing up more usable AC power for running electrical devices and appliances and reducing the likelihood of tripping shore power breakers.Electrical Specifications (@ 25 degrees C unless otherwise noted): Output Current (nominal): 40 A  Output Voltage (nominal, depending on settings): Charge 14.2–15.5; Float 13.4–13.8 Vdc; 16 V DC Output Connections: Three AC Input Voltage: 90–265 Vac; 47–63 Hz 120 Vac, 230 Vac, 240 Vac nominal Temperature Compensation: Three settings  Charger Efficiency: > 80% Battery Type: Gel, Flooded, AGM, LiFePO4  Minimum Recommended Battery Bank Size: 80 Ah General Specifications: Operating Temperature Range: 0–60°C (32–140°F)  Storage Temperature -40–80°C (-40–176°F) Battery Connection: Three positive terminals and one negative terminal Dimensions (H x W x L): 70 x 170 x 250 mm (2.8 x 6.7 x 9.8”) Weight 2.2 kg (4.8 lb) Regulatory Approvals Meets CSA 60335-2-29, CE Marked for the Low Voltage Directive (safety) and the EMC Directive, UL1564, IEC 60335-2-29, IP32 per EN.IEC 60529, FCC Part 158, Canada ICES-003 Class B emissions limits, ABYC A-31, and DOE/CEC energy efficiency compliant.This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns. Specifications: Charger Output - Amps: 40a Charger Output Voltage: 12v Charging Banks: 3 Portable: No Box Dimensions: 6"H x 11"W x 14"L WT: 6.1 lbs UPC: 715535920814 Quick Guide (pdf)Owner's Manual (pdf)Brochure (pdf)

Read more less

Dual PowerPost Connectors Designed for connecting high amp conductors Includes one black and one red insulator WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less

On-Board Precision Charger MK-110 PCL 1 Bank x 10 AMP LI Optimized ChargerLonger run times. Shorter charge times. That's the precision difference that keeps anglers on the water longer and puts more fish in the boat. Now, the next generation of this legendary line of chargers has been optimized for 12-volt lithium (LiFePO4) batteries. Precision chargers feature battery-type selection by the bank, which now includes charge curves specially formulated for the high demands of lithium batteries, and can even wake these battery types from standby. Features: Battery Type Selection: Each charging bank can be selected to your specific battery type (Lithium (LiFePO4) AGM or flooded lead acid) to guarantee a safe, protected charge Automatic Temperature Compensation: Precision chargers sense and adjust to ambient temperature fluctuations to ensure a fast, accurate charge Low-Line Voltage Compensation: When outlets don't put out the 120 volts they are supposed to, Precision Chargers compensate to deliver a fast, consistent charge no matter what Battery Equalization: Cleans and protects your battery (flooded lead-acid only) every time you plugin. Also activates a more rigorous, complete cleaning at the push of a button Digital Control: Microprocessor-based design delivers a faster, more precise charge every time. Precision chargers can even wake dead 12-volt lithium (LiFePO4) batteries from standby automatically. LED Indicator Lights: Inform of charge stage, maintenance mode status, error notifications, and full charge Automatic Multi-Stage Charging: Controls the voltage and current your battery gets throughout the charging cycle, ensuring a fast, safe and precise charge Waterproof Construction: All on-board chargers are built to be waterproof, shock-resistant and vibration-resistant 3-Year Warranty: All battery chargers come with a full 3-year replacement warranty Specifications: Product Dimensions: 9.88 in x 4 in x 3.5 in Product Weight: 4 lb Charger Style: On-Board Output per Bank: 10 amps Wattage: 150W Charge Time: 4-6 hours Power Source: On-Shore AC Battery Type: 12v Lithium LiFePO4, 12v AGM, 12v Flooded Lead Acid 12v Lithium-Ion (LiFePO4) Optimized: Yes Waterproof: Yes Digital Control: Yes Automatic Temperature Compensation: Yes Battery Equalization: Yes Battery Type Selection: Yes LED Display: Yes Saltwater Compatible: Yes Battery Connection: Ring Terminal Warranty: Three-Year Warranty Specifications: Charger Input - Voltage: 120v Charger Output - Amps: 10a Charger Output Voltage: 12v Charging Banks: 1 Portable: No Box Dimensions: 6"H x 8"W x 18"L WT: 2.5 lbs UPC: 029402049950

Read more less

Round Red LED Temperature MeterThe temperature meter includes a prewired temperature sensor with a 6-foot cable and it monitors temperature on a bright LED screen. Features: Reverse polarity protected The same compact round size as a standard 12VDC receptacle, this temperature meter supports many installation options Constructed of injection-molded nylon Installation is as easy as drilling a 1-1/8-in. hole, inserting the socket body, tightening the locking nut, and connecting the wires IP67 waterproof rating 12-24VDC Specifications: Diameter: 1-7/16 in. Length: 1-1/16 in. Height: 1-1/8 in. Volts: 12-24 Temperature Range (Fahrenheit): -67 degrees to 248 degrees  Weight: .02 lb. WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less

SPST Sealed Toggle Switch - OFF/ONSingle pole, single throw toggle switch turns one circuit on and off. Common applications include use for any single circuit requiring an on-off style switch. Completely sealed switches built to stand up to the most extreme conditions. Engineered to IP67 specifications utilizing a double o-ring within a bushing at the toggle and a full epoxy seal at the back.Features: Nominal voltage is 12V/24V DC Rated for 25A at 12V DC, 15A at 24V DC 10" 14 AWG wire lead terminals Mounting stem 15/32" fits panels up to 1/8" thick Same as Cole Hersee part number 55025 WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Action: On/Off Color: Chrome Throw/Pole: SPST Box Dimensions: 2"H x 3"W x 5"L WT: 0.2 lbs UPC: 870216046693

Read more less

8267Contura Switch Mounting PanelEnd Mounting Panel Modular design permits easy assembly in groups of varying sizes Designed for mounting in 6 different panel thicknesses: 0.06" (1.57mm) 0.09" (2.36mm) 0.13" (3.17mm)0.19" (4.75mm) 0.25" (6.35mm) 0.38" (9.52mm) WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less

SPST Water-Resistant Toggle Switch - OFF/ONSingle pole, single throw toggle switch turns one circuit on and off. Common applications include any single circuit requiring an on-off style switch. PVC coated for water resistant integrity.Features: Nominal voltage is 12V Rated for 25A at 12V DC 8" 16 AWG wire lead terminals Mounting stem 15/32" fits panels up to 3/16" thick Same as Cole Hersee part number 5582-30 WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Action: On/Off Color: Black Throw/Pole: SPST Box Dimensions: 2"H x 3"W x 5"L WT: 0.2 lbs UPC: 870216046754

Read more less

70A Trolling Motor ReceptacleIncreased amperage for modern trolling motors.Features: 70A continuous rating Sealed, waterproof connection Integrated strain relief Keyed design with thumbprint locator Accepts up to 6AWG wire WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less

10AMP - 12/24V 2 Bank 120V Input On-Board Battery ChargerThese onboard chargers have the same housing and mounting dimensions as our traditional Charge Pro Guest chargers with a number of performance enhancements.Features: Charge flooded, AGM or Gel batteries Microprocessor controlled for accurate charging Universal input 120/230V input for go-anywhere freedom Intuitive operation Sense-Send™ technology senses the power needs of each battery and sends correct charge Isolated outputs Outputs can be put in series or parallel for higher voltage or current Completely sealed, epoxy filled IP68 waterproof Designed for harsh marine and industrial environments - moisture, salt, shock and vibration tested Non corroding housing for ultimate reliability Meet global industry standards including UL*, CE, CSA, ABYC, California efficiency regulations (CEC) Footprint same as former Charge Pro Guest Chargers ConnectCharge Plug for easy assembly to inlet (Item #150CCI) with no wiring * UL certification pendingWARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Charger Output Voltage: 12/24v Charger Output - Amps: 10a Charging Banks: 2 Portable: No Charger Input - Voltage: 120/230v Box Dimensions: 3"H x 9"W x 9"L WT: 6.1 lbs UPC: 093344058264 Owner's Manual (pdf)

Read more less

8259Contura Switch Mounting Panels3 Position Mounting Panel Modular design permits easy assembly in groups of varying sizes Designed for mounting in 6 different panel thicknesses:0.06" (1.57mm) 0.09" (2.36mm) 0.13" (3.17mm)0.19" (4.75mm) 0.25" (6.35mm) 0.38" (9.52mm) WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less

2-Position Ignition Switch - OFF/ONMarine-grade battery ignition and start switch suitable for harsh environments on land or sea.Features: Coded tumbler lock, includes two keys Nominal voltage is 12V DC Rated for 10A at 12V DC #8-32 screw terminals Fits panels up to 1" thick Same as Cole Hersee part number M-489 WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Color: Chrome Action: On/Off Box Dimensions: 2"H x 3"W x 5"L WT: 0.4 lbs UPC: 870216046167

Read more less

30A 125V Power Inlet303SSEL-BProduct Features Solid cast 316 stainless steel Locking waterproof cap Easy Lock System Soft Touch cap stays open in the upright position 8-way right angle rear safety enclosure WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Type: Inlets Box Dimensions: 4"H x 6"W x 9"L WT: 1.25 lbs UPC: 093344300172 Quick Guide (pdf)Owner's Manual (pdf)Brochure (pdf)

Read more less

TILE USB-A/USB-C Interior Charging Socket - 12/24V - Stainless Steel BezelTILE Series offers sleek, high-performance charging solutions designed specifically for marine interiors. These chargers blend seamlessly into luxury marine environments. Featuring a compact 40mm (1.57”) footprint and requiring just a 29mm (1.14”) hole saw for easy installation, the TILE Series combines functionality and style, making it the ideal choice for modernizing your vessel’s interior. Enhance your boat’s space with this practical, sophisticated solution for charging your everyday devices.Tile USB is FAST! It will charge at 36W on a 12V system or up to 60W on a 24V system. This makes it perfect for charging modern laptops and large tablets, phones, and any other USB-C-powered devices onboard.USB–C output60W max on 24V system, 36W max on 12V systemUniversalUniversal fit for any USB-C connectors. Fast charge (60W max) up to 2 devices at a time.Important informationTo maximize charge performance, use the cable supplied with your tablet, phone, etc. (C to C, or C-lightning) Phones charge at the same speed on either a 12 or 24V system, but a 24V system must be used to get the full 60W output suitable for laptops.WARNINGTILE USB products are designed for interior use only. Do not install in locations where water exposure is possible, as this may lead to product failure.Features: 12V & 24V  USB-A and USB-C Ultra-low profile Front fit Tiny footprint Available in 316 stainless steel or matte black Conformal coated electronics, protected against moisture Modernize your boat's interiors Specifications: Input Voltage Range: 10-32V DC (12/24V system) Input current max: Max 6A (10A fuse recommended)  Output (Type C): 12V System: 5V=3A, 9V=3A, 12V=3A Max, 24V System: 5V=3A, 9V=3A, 12V=3A, 15V=3A, 20V=3A Max Output (Type A): 12V System: 5V=3A, 9V=3A, 12V=3A Max, 24V System: 5V=3A, 9V=3A, 12V=3A, 15V=3A, 20V=3A Max Standby Power: 0.01W Certification: CE, FCC, UKCA, C-Tick, ROHS, WEE

Read more less

Contura II Switch SPST Black - OFF-ONVibration, shock, thermoshock, moisture and salt spray resistantMounts in Blue Sea Systems Contura Water Resistant Panels and Contura Switch Mounting PanelsSpecifications: Action: OFF-ON Pole/Throw: SPST - Single Pole/ Single Throw Actuator Color: Black - Contura II Common Applications: Lights Maximum Amperage: 20A @ 12V / 15A @ 24V Amperage Operating Current: 18mA (LED) Minimum Operating Temperature: -40° C Maximum Operating Temperature: 85° C Actuator Position to Light LED: ON Embedded LEDs: 1 Lighting: LED rated 100,000 hours 1/2 half Seals: Internal and external gasket panel seal Weight: 0.09lb (0.04 kg) WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Action: On/Off Color: Black Throw/Pole: SPST Box Dimensions: 2"H x 2"W x 4"L WT: 0.2 lbs UPC: 632085079291

Read more less

5005 ANL 35-300AMP Fuse Block with CoverFeatures: Insulating cover satisfies ABYC/USCG requirements and cover breakouts allow access in any direction For use on systems up to 32V DC Large 5/16" - 18 studs accept 5/16" (M8) ring terminals, 14 AWG to 2/0 AWG wire WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Fuse Type: ANL Type: Fuse Blocks Box Dimensions: 2"H x 4"W x 8"L WT: 0.4 lbs UPC: 632085050054

Read more less

Active GPS Antenna for GX LTE ModemThis antenna is for the GX LTE Modem.Specifications: Mounting Option: Magnet Cable Type: RG-74 Cable Length: 3.0 m Connector: SMA male straight Frequencies: 1575.42 MHz Signal Gain: 50 Ω Please contact your dealer for any returns, repairs or support issues related to this product. Quick Guide (pdf)Owner's Manual (pdf)

Read more less