18" x 14" Heavy Duty Performance Trim Tab Kit w/o Switch Kit -12VLenco Electric Heavy Duty Polished Blade Trim Tab Kits are supplied with electric actuators for precise control. Fully submersible with all Plug & Play Deutsch connections. Blades are Electro-Polished 12 gauge - 304 SS with 1" turned up edges, 85 degree inside taper and 1/4" diameter hinge pin. Kits equipped with Extreme Duty actuators with 5/16" SS bolts. Kit is factory assembled with full transom back plate, mechanical strain relief cable seal, adjustable C-channel mounting brackets and 3.75" sacrificial anodes. .Kit Contents: 2 each of 12-gauge stainless steel Electro-Polished trim tab blades  2 each of #15055-001 XD extreme duty actuators with 6' lead and Deutsch plugs 2 each of #30133-103  20' actuator extension wiring harnesses 1 each of the Lenco owner’s / installation manual Boat-mounting hardware supplied by customer Specifications: Suggested Boat Length: 22' to 42' Length of Tab: 18" Width of Tab: 14" Minimum Transom Height: 10.5" Blades: 12 Gauge Stainless Steel Finish: Electro-Polished Switch Kit: Sold Separately Class: Fuel Efficient Compliance: CE Certified Compatibility: Any Boat Switch Required: 15069-001 or 15070-001 Actuators: 12-volt WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns. Brochure (pdf)

Read more less

Euro-Style Rocker Switch ControlThis control is ergonomically designed, water resistant and provides a positive "click" when the trim tabs are engaged. Its lockout feature prevents user from pressing down on opposite directions at the same time. The control is easy to install, fitting into any existing Bennett 2 1/2-inch Rocker Switch hole.Bridge control comes with a 20' wire WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Read more less

D-A Intermediate Foam Polishing Pad 40mm - Light Blue *6-PackThe RUPES D-A INTERMEDIATE Foam Pad joins the RUPES D-A Series foam pad range, positioned between the D-A FINE yellow pad and the D-A COARSE blue pad. It is the most versatile foam pad in the BigFoot range and can be used with several RUPES compounds, such as D-A COARSE and D-A FINE, as well as UNO ADVANCED and UNO PROTECT.It has the polishing power to remove severe defects from a wide variety of painted and solid surfaces when paired with RUPES D-A COARSE blue compound.When used with RUPES D-A FINE yellow polishing compound, it removes moderate-to-fine defects and creates a high-gloss finish.The highly engineered foam formula really shines when paired with UNO PROTECT or UNO ADVANCED for final polishing and creating a durable layer of protection.*Use with all dual-action polishers Specifications: Type: Buffers & pads Box Dimensions: 1"H x 1"W x 4"L WT: 0.1 lbs UPC: 8059519688980 Quick Guide (pdf)Owner's Manual (pdf)

Read more less

TMR-1 Remote for Ghost Trolling MotorFeatures: Adjust speed Change direction Set Anchor Includes lanyard Quick Guide (pdf)

Read more less

Marine Ultimate Vinyl Boat Seat Care KitThe Complete Process to Treat and Prevent Mold & Mildew on Vinyl Boat Seats! Say goodbye to mold and mildew on your boat! The Xanigo Marine Ultimate Vinyl Boat Seat Care Kit is here to save the day. This kit includes everything you need to remove and prevent unsightly mold and mildew on your vinyl boat seats, life jackets, canvas, bumpers, carpets, and other areas with high moisture.Three Solutions | Four Easy Steps: Step 1 Remove: Simply spray a generous amount of the Mold & Mildew Stain Remover onto the affected area and let it soak for 60-90 seconds. Agitate the area with a stiff brush to remove the mold from the pores and let the product do its job, leaving behind a clean, like-new, seat! Thoroughly rinse away the residue with fresh water. Don't forget, no direct sunlight! Repeat if necessary. Step 2 Neutralize: Spray the Waterless Wash onto your seats and wipe it in with a microfiber cloth to neutralize the chemicals in the remover and prime the surface for the Mold & Mildew Preventer to bond to. That's it! Step 3 Prevent: Simply spray the Mold & Mildew Preventer onto a clean, dry surface and spread it evenly with a microfiber towel. That's it! With just one application, your boat will be protected against mold and mildew for up to 90 days. No wiping is required! Step 4 Maintain: Spray the Waterless Wash and wipe it down with a microfiber towel to clean away grime and sunscreen from your seats, all while enhancing the protective layer created by the Mold & Mildew Preventer. Do this every time you use your boat to keep it clean, fresh, and mold-free! What's Included? (1) 16 oz. bottle of Mold & Mildew Stain Remover (1) 32 oz. bottle of Mold & Mildew Preventer (1) 32 oz. bottle of Waterless Wash Brochure (pdf)

Read more less

Liquid Life-Calk Sealant Tube - 2.8 FL. Oz. - BlackHas same outstanding properties as Life-Calk® Sealant such as long-lasting, permanently flexible, can be sanded, painted*** and used above and below the waterline. Tack-free in 1 to 3 days. Excellent resistance to teak oils, gasoline and diesel fuel. Ideal for teak decks, to bed deck and hull hardware, seal thru-hull fittings, and underwater seams. Will bond to fiberglass, wood, metal, glass, and itself. Cures to a firm flexible rubber seal with excellent waterproofing and adhesion qualities. Can be applied to damp surfaces. Low viscosity, free-flowing polysulfide sealant for use on fine cracks and seams.*Not compatible with all paints, Sikkens, Cetol, Deks, OljeWARNING: This product can expose you to chemicals including Toluene which is known to the State of California to cause birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less

HydroSwipe Chamois Cloth - 24" x 32"HydroSwipe is a handy, high-absorption chamois cloth that is perfect for drying the interior and exterior of boats, yachts, and cars. It features durable material that doesn’t lose absorption capability. Wet to activate, wring it out, and wipe the surface to absorb water. Use it over and over again. It is lightweight, glides across the surface, and is quick to dry. Specifications: Type: misc Box Dimensions: 3"H x 3"W x 10"L WT: 0.65 lbs UPC: 850005213390

Read more less

Small Offset Trolling Motor Plate for Garmin KrakenThe Sea Brackets Small Offset Trolling Motor Mounting Plate, designed for the Garmin Quick Release Plate System, offers a robust and reliable solution for installing any Force Kraken Trolling motor. Crafted from 6061 T6 aluminum, each plate is primed, powder-coated, and UV-protected for exceptional durability against the elements. Whether for port or starboard installation, these plates boast clean, accurately gauged holes for seamless bolt engagement.Suggested Hardware: 316L stainless steel hardware is recommended for rust prevention Mounting hardware is included with Garmin's Quick Release Plate System Backing disk from Sea Brackets or an alternative backing support system 1/4–20 flat-head Phillips machine screws, fender washers, and lock nuts 5/16–18 Flat-head Phillips machine screws, fender washers, and lock nuts Dimensions:18.5" x 13.5" x 1/2"Note: Hardware length is dependent on the thickness of the hull, backing hardware, and other various components.

Read more less

14" Straight Trolling Motor PlateThis trolling motor mounting plate is manufactured using 6061 T6 aluminum, which is primed, and powder-coated with added UV protection for a high-quality and durable product. The tapped holes in the brackets are clean and free of powder coat, as well as gaged for accuracy and consistency for ease of bolt engagement. Sea Bracket's manufacturing process is so reliable that the bracket can be used universally for both port and starboard installation.1/2" 6061 aluminum (compatible with Rhodan QRB, Minn Kota RTA-54, and RTA-62).Specifications:Plate Dimensions (inches): 14" x 8" x ½”Suggested hardware: 1/4–20 tapered Phillips machine screws, fender washers, backing plates, and locknuts  316 stainless steel is ideal for corrosion prevention Mounting hardware that comes with the Rhodan quick-release bracket or mounting hardware that comes with the Minn Kota RTA-54/ RTA-62

Read more less

16" Straight Trolling Motor PlateThis trolling motor mounting plate is manufactured using 6061 T6 aluminum, which is primed, and powder-coated with added UV protection for a high-quality and durable product. The tapped holes in the brackets are clean and free of powder coat, as well as gaged for accuracy and consistency for ease of bolt engagement. Sea Bracket's manufacturing process is so reliable that the bracket can be used universally for both port and starboard installation.1/2" 6061 aluminum (compatible with Rhodan QRB, Minn Kota RTA-54, and RTA-62).Specifications:Plate Dimensions (inches): 16" x 8" x ½”Suggested Hardware: 1/4–20 tapered Phillips machine screws, fender washers, backing plates, and locknuts  316 stainless steel is ideal for corrosion prevention Mounting hardware that comes with the Rhodan quick-release bracket or mounting hardware that comes with the Minn Kota RTA-54/ RTA-62

Read more less

Thruster Joystick Panel ControllerControl your Lewmar bow thruster using the joystick panel.Compatible with: Lewmar 110TT Lewmar 140TT Features: Plug 'n' Play connection from joystick to Thruster means dual station control is possible On/Off illumination Easy installation connection *Sold as an Individual

Read more less

Dual Locking Flush Deck Socket MountTwo attractive mirror polished 18-8 stainless steel flush deck socket sets, features a push button lock pin and includes a flange gasket with integral flip-up water seal cap.  These sockets mount flush for an uncluttered deck. Compatible With:Dual Mounted Grills and Tables Technical Specifications: Material - 18-8 Stainless Steel Dimensions (installed) (W x H) - 2-5/8" x 1-15/32" (9.7 x 3.7 cm) Weight - 1.51 lb (.69 kg) *Sold as a Pair Owner's Manual (pdf)

Read more less

GripTide™ Non-Skid Deck Coating Kit - Sail WhiteGripTide™ is a two-component high quality urethane, grip-enhancing, textured coating that provides a durable, protective finish for boat floors, boat decks and other marine surfaces.Features: 2K technology for durability and a quick cure Easy one-step spray or roller application Durable coating that maintains flexibility Adhesion to most surfaces Five popular marine colors Chemical resistant Fade resistant Applications: Fiberglass & SMC Gelcoat Fully cured unfinished & unsealed concrete Dry wood / engineered wood Primed or painted surfaces Properties: Coverage: 75 sq. ft. per gallon Kit contains 1 Gallon GripTide Non-Skid Deck Coating, 1 Cone Quart GripTide Catalyst, and 1 (9") GripTide Deck Coating Roller Brochure (pdf)

Read more less

Washdown Water Outlet - 316 Stainless SteelThe Washdown Water Outlet allows for a garden hose to be hooked up to the onboard water system for use as a washdown system. Standard male hose connector. Requires separate ball or gate valve to regulate water flow. Pipe size: 1/2" FIPT x 3/4" MGHT. Constructed of corrosion resistant investment cast 316 stainless steel. WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less

Lanocote Rust & Corrosion Solution - 16 oz. LanoCote works on these five basic principles: displaces water, absorbs corrosion, forms moisture barrier, penetrates and high lubricity. LanoCote is extremely effective in preventing and stopping corrosion on all types of metals under all environmental conditions. Formulated to withstand salt water marine conditions, LanoCote is particularly useful in preventing thread seizure due to all types of corrosion on boats and machinery.Applied during assembly, LanoCote will greatly assist in easy dismantling years later. An example would be anchor shackles which are regularly immersed in salt water. LanoCote also combats galvanization where dissimilar metals are fastened together, such as stainless steel fittings on alloy masts etc. Features: Prevents Thread Freeze-up Combats Galvanic Reaction of Dissimilar Metals Seals Porous Surfaces Neutralizes Acids, Alkalies, & Salts Prevents Corrosion on Electronic Contacts Specifications: Type: Corrosion Protection Box Dimensions: 4"H x 4"W x 4"L WT: 0.95 lbs UPC: 028026136268

Read more less

Oblong Captive Garboard Drain & Plug - 316 Stainless SteelThis Oblong Captive Garboard Drain & Plug sits lower in the stern for more water removal. Captive plug prevents plug from being lost. Constructed of corrosion resistant investment cast 316 stainless steel. Installs with two #8 FH fasteners (not included). WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less

Fillet Table Only - 30" Features: UV stabilized high-density polypropylene Solid one-piece construction for long life and easy maintenance Large, 30" wide by 12-5/8" deep, includes hose holder and towel bar Easily accessible knife and pliers holders Knives and pliers not included DOES NOT INCLUDE MOUNTING HARDWARE WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Width: 30" Box Dimensions: 3"H x 17"W x 33"L WT: 7.25 lbs UPC: 035514326810

Read more less

Boat Hook Silicone Squeegee Heavy duty silicone blade provides a wide (12”) coverage area to easily clean and clear any type of window or marine surface. Comfort grip allows for manual use or attach to any Sea-Dog® boat hook and all universal threaded devices. Universal/Acme ThreadWARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Type: Tools & Accessories Box Dimensions: 2"H x 6"W x 14"L WT: 0.65 lbs UPC: 035514491907

Read more less

Steering Cable Boot Durable molded rubber boot protects the output end of all standard steering cables keeping dirt, debris and moisture out extending the service life of the cable. Includes two cable tie style clamps. WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less

Hatch TapeLength: 8'Height: 1/4"Width: 3/4"Color: BlackTACO Metals supplies quality hatch tape that is designed to protect boat interiors and exteriors from the harsh marine environment. Well suited for use in live wells, hatches and other enclosures. TACO hatch tape products are made of specially formulated rubber compounds, designed and engineered to provide maximum sealing capacity and protect against weathering and vibration. Creates a tight, rattle-free seal Adhesive backing for convenient installation Durable, flexible sponge rubber compound This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Read more less

Carbon Fiber Flag Pole with J-Lock System - 54"Take your marine flag display to the next level with the Easy n’ Secure Fit Carbon Fiber Flagpole. Built for today’s boater, these flagpoles pair ultralight durability with high-strength carbon fiber construction, delivering exceptional performance without added weight. Featuring our patented twist-and-lock technology, they install effortlessly into existing hardware and stay firmly in place— no rattle, no fuss. The result is a clean, premium presentation that enhances vessels of any size.Features Fits 3' x 5' flags Patented twist-and-lock system for quick, secure install/removal Lightweight Carbon Fiber material with clear, Awl Grip UV-protection Corrosion-resistant hardware, built for harsh saltwater conditions 360° tangle-free swivel keeps flags flying freely Fits standard 1-5/8” rod holders and gunwale mounts Rattle-free fit with precision tapered wedges (including 30° wedge) Stable and secure, even at cruising speeds Versatile mounting options Brochure (pdf)

Read more less

Thru-Hull Installation Tool Thru Hull Installation ToolThe Concept:THT-530 makes the installation of standard GROCO thru-hull fittings possible by a single installer.  Slide the thru-hull fitting, flanged end first, over the tool.  (It will stop at the proper step.)  Tie a length of monofilament to the eye and place it into the already-cut hole in the hull of the boat.  Apply caulking to the flange of the fitting, and pull the fitting through the hole and against the hull from inside the boat.  Thread the mono-filament through the locknut or seacock. With the fitting pulled firmly against the hull the locknut or the seacock may be screwed onto the fitting.THT-530 fits GROCO Thru-hull Fitting Sizes from 1/2" through 3"

Read more less

Whale Tail XLAluminum Stabilizer and Ski Boat FinImproves performance in any I/O or outboard motor!The Whale Tail XL extends out behind the prop to utilize prop wash energy which is normally lost. Whale Tail transforms this energy into lift for immediate response when the throttle is applied. Unique hydrodynamic design Stabilizes bow-light boats Pops skiers up in less time Flattens wake for water skiing; creates positive, skid-free turns: With bow lowered, visibility and safety is improved Smooths out ride in rough water Reduces porpoising & cavitating Increases top speed and fuel savings in most applications Mounts on the anti-cavitation plate of all inboard/outboards and outboards Installs in 15 minutes with stainless steel hardware included Marine grade aluminum with durable anodized finish Use the Whale Tail XL year-round in freshwater or saltwater to improve performance of any boat!

Read more less

Happy Troller - Large Plate Large Troller: Fits inboard/outboards plus all outboard motors 50 hp and larger.For the Fisherman who thinks he has everything!Slows even big motors down to that "ever-so-slow" fish tantalizing speed.A significant invention in the sport of troll fishing, Happy Troller® mounts on the anti-cavitation plate to allow fine control of trolling speed. At cruising speed, your boat's stability is enhanced.Locks in "down" position for trolling.Locks in "up" position for cruising.Happy Troller is the answer to correct trolling speed. Use it year-round in all boating activities; salt and fresh water.Key Features: Reduces troll speed in "down" position Acts as a stabilizer in "up" position Maintains stability in bow-light boats Smooths out ride in rough water Reduces porpoising and cavitation Made of only highest quality stainless steel and marine aluminum; clear anodized aluminum finish Installs in 15 minutes Stainless steel mounting hardware and installation & operating instructions provided with each unit Owner's Manual (pdf)

Read more less

Deluxe Stainless Steel Wiper Blade - 22"These blades work well on curved or flat windshields.Features: Works well on curved or flat windshields All stainless steel construction Marine grade silicone squeegee

Read more less

ROKK Mini Mount Kit - Rail Mount - Tablet ClampUniversal design ensures you have all the pieces needed to mount a variety of tablets on a Scanstrut Mini Mount and Adjustable Body.This three (3) part kit installs in minutes and allows quick release of mounted equipment.Features: Engineered to withstand high shock loading. Quick Fit I Quick Release - Install your devices instantly onboard.  With one reassuring click your tablet is both secured and released.    Adjustable - fits devices from 4.92" - 8.66" (125mm to 220 mm)  Solid Install - A metal-on-metal locking system multiples your clamping efforts to achieve 100% locking force.  Your electronics will never move; until you want them to Base secures to a flat surface with included hardware. In the Box: RL-508 ROKK Tablet Clamp RLS-AM ROKK Mini Adjustable Arm RLS-401 ROKK Mini Rail Mount *Sold as a Kit Specifications: Cut/Uncut: Cut Mounting Style: Rail Box Dimensions: 3"H x 9"W x 11"L WT: 1.4 lbs UPC: 5060114795730 Quick Guide (pdf)Brochure (pdf)

Read more less

ROKK Mini Self-Adhesive Surface Mount3M self-adhesive base mount that fits any flat surface. Features: No drilling required to install Works on any flat surface *Sold as an Individual Specifications: Cut/Uncut: Cut Mounting Style: Universal Box Dimensions: 2"H x 4"W x 5"L WT: 0.3 lbs UPC: 5060114795570 Quick Guide (pdf)

Read more less

Deluxe Stainless Steel Wiper Blade - Black - 24"These blades work well on curved or flat windshields.Features: Works well on curved or flat windshields All stainless steel construction Marine grade silicone squeegee

Read more less

Tip Top Teak Crystal Deck Cleaner - Half Gallon (4lbs 3oz) - *Case of 6*Tip Top Teak's Crystal Deck Cleaner is just what you need to begin therestoration of you ship's teak. Crystal Deck Cleaner is specially designedfor those large open areas on your deck that have endured quite a bit ofwear and tear.Features: Easy to use formula Concentrated formula cleans more deck than liquid cleaners Specially designed for teak Specifications: Type: Teak Box Dimensions: 5"H x 5"W x 9"L WT: 26.4 lbs

Read more less

ROKK Mini Mount Kit - Suction Cup Mount - Phone ClampThe ROKK Mini universal phone mounting kit is the toughest mounting system for your telephone.The hi-performance ROKK mini modular system allows you to attach your electronics to boats, cars, off-road vehicles, aircraft and more.  Move your electronics conveniently between different types of base mounts in different locations in one easy click. Want to unlock multiple mounting options in different locations or simply mount a different electronic device?  Just add another top or base to your modular kit and extend possibilities of your ROKK mini starter kit.This three (3) part kit installs in minutes and allows quick release of mounted equipment.Features: Engineered to withstand high shock loading. Secure mount for smart phones, handheld GPS and other small devices. Base secures to with included hardware. In the Box: RLS-405 ROKK Mini Suction Cup Mount  RL-509 ROKK Universal Phone Clamp RLS-AM ROKK Mini Adjustable Arm *Sold as a Kit Specifications: Cut/Uncut: Cut Mounting Style: Universal Box Dimensions: 3"H x 4"W x 4"L WT: 1.2 lbs UPC: 5060114796010 Quick Guide (pdf)Brochure (pdf)

Read more less

Trim Tab AnodeMaterial: ZincOuter Diameter: 3.54"Length:4.13"Weight: 1.06lbs Specifications: Material: Zinc Box Dimensions: 3"H x 4"W x 5"L WT: 1 lbs UPC: 8033837064190 Quick Guide (pdf)Owner's Manual (pdf)

Read more less

Yamaha 200-300HP Anode Kit - Hi-PerformanceContents: (1) 01112 (1) 01145 Material: ZincPackaging: PolybagHardware: Included Specifications: Material: Zinc Box Dimensions: 3"H x 6"W x 8"L WT: 3.5 lbs UPC: 8059617818944 Quick Guide (pdf)Owner's Manual (pdf)

Read more less

Shaft AnodeMaterial: ZincOuter Diameter: 2.58"Inner Diameter: 1.50"Height: 2.62"Weight: 1.37lbsHoles: 4 Specifications: Material: Zinc Box Dimensions: 2"H x 2"W x 3"L WT: 1.4 lbs UPC: 8059617812423 Quick Guide (pdf)Owner's Manual (pdf)Brochure (pdf)

Read more less

TEC-DIVERS Plate AnodePlates for HullsMaterial: ZincLength: 12.01"Width: 5.98"Height: 0.51"Weight: 7.78lbs Specifications: Material: Zinc Box Dimensions: 1"H x 6"W x 12"L WT: 7.8 lbs UPC: 8033837068730 Quick Guide (pdf)Owner's Manual (pdf)

Read more less

Trim Tab AnodeSkeg For Engines - Yamaha 200-250Material: ZincTab Height: 2.76"Outer Diameter: 3.94"Weight: 1.50lbs Specifications: Material: Zinc Box Dimensions: 4"H x 4"W x 6"L WT: 1.5 lbs UPC: 8033837065296 Quick Guide (pdf)Owner's Manual (pdf)

Read more less

Shaft AnodeMaterial: ZincOuter Diameter: 3.20"Inner Diameter: 1.75"Height: 3.06"Weight: 2.56lbsHoles: 4 Specifications: Material: Zinc Box Dimensions: 3"H x 3"W x 3"L WT: 2.7 lbs UPC: 8059617812454 Quick Guide (pdf)Owner's Manual (pdf)Brochure (pdf)

Read more less

Quick Release Mounting Bracket for Axis & Shallow Water Anchors - BlackRemoving your Lewmar shallow water anchor is a breeze with our compatible quick-release mounting bracket. Available in black or white, this dovetail-style bracket mounts directly to your boat’s transom or our other available mounting brackets, allowing for slide-out removal of your shallow water anchor for trailering, storage, or switching between boats.The motor mounting bracket for shallow water anchors attaches directly between the outboard motor and the transom, eliminating the need to drill into your boat's hull. Its powder-coated aluminum finish offers long-lasting durability in marine environments. Designed for use with Lewmar shallow water anchors, this bracket offers a secure and reliable fit. Professional installation is recommended, as specialized equipment is required to support the motor properly during installation. Using basic tools, the motor mounting bracket is compatible with the Quick Release bracket for easy anchor removal. Features: For use with the Axis™ and Vector™ shallow water anchors DIY installation with included hardware Dovetail style mounting bracket securely holds the anchor in place Compatible with other Lewmar shallow water anchor mounting brackets Allows anchor to be easily removed with simple hand tools for transport, storage, or use on other vessels Durable powder-coated aluminum finish withstands harsh marine conditions Designed for port or starboard mounting Measures 8" x 6" x 1.5" Specifications: Color: Black Anchor Style: Shallow Water Hardware Type: Mounting Hardware Item Length: 8" Item Width: 6.5" Item Height: 1.5" What's Included? Mounting hardware Installation instructions

Read more less

140TT 2.2kw Gen. 2 Bow Thruster - 12VManeuvering around the dock area can be difficult, but Lewmar’s TT Thrusters make docking simple.The revolutionary design of the TT propeller, the latest in Lewmar’s long history of custom thruster solutions, achieves a perfectly even thrust in both directions for maximum control and maneuverability.All Lewmar Thrusters have been extensively tested, resulting in a smooth, efficient, and quiet performance that will have you docking like a pro in no time.Features: No reservoir to install, no leaks, and no maintenance High performance 5 blade propellers give equal thrust in both directions High integrity seal Spline driven propeller, no drive pin or anode required Blue box electronics prevent misuse and protect motor Hardened and ground spiral bevel gear for maximum efficiency and quiet power transmission Self-resetting thermal protection  Easy plug together switch connections Minimum silhouette hub for smooth water flow Technical Specifications: Voltage - 12V Power - 2.2 KW Power - 3 HP Tunnel Size - 5.5" Thrust - 92lb Weight - 29lb *Sold as an Individual Owner's Manual (pdf)

Read more less

Anode Kit for 140 TTSpare anodes used in conjunction with Lewmar thruster fitted with a bronze hub.In the Box: Anode Mounting hardware *Sold as an Individual

Read more less

Size 44 Low Profile Hatch Seal KitReplacement seals for the Low Profile hatch range. Works by holding the Acrylic pane into the frame.In the Box: Gasket Instruction manual *Sold as an Individual 

Read more less

Waterproof Wiper Motor 12V - 2.5" Shaft - 80° SweepThe 1.5 Waterproof Wiper Motor is made with a fully sealed powder coated aluminum waterproof base and housing to power a 22" Deluxe arm and 22" Deluxe blade combination or a 20" Premier arm and 20" Premier blade combination.Features: Available in three shaft lengths: 1.5", 2.5" and 3.5" (includes .5" length of knurled arm fitting) Factory pre-set sweep angles of 80 degrees or 110 degrees, with easy adjustment to 45 degrees or 60 degree Chrome plated solid brass knurled drive nut with brass and stainless steel driveshaft Two-speed motor Sealed 6" wire leads, 16 AWG Adjustable right or left self-parking 0.625" diameter shaft (16 mm) Available in 12V and 24V models Coast to park RF shielded circuitry Retail version includes 5 amp fuse and holder (operating switch not included) Measures approximately 7.75" L x 4" W x 2.75" D Stall torque: 109 in-lbs (125 kgf/cm; 12.3 Nm) Stall current: 11.5-13.0 amps No load current: 0.5-1.2 amps Replaces AFI 2000 motor

Read more less

Elastometric 3 oz (89ml) Sealant Tube - WhiteA one-part, fast skinning (10 minutes) and fast curing (24 hours) multi-purpose marine grade sealant with superior strength, adhesion, elongation and life characteristics. Cures in temperatures of -20°F (-28.9°C) to 120°F (-48.9°C) and can be wet sanded and painted after curing. Flexibility and compression capabilities are excellent. Heavy duty use above or below the waterline. Twists, bends, expands, compresses. Seals ports, beds hardware, stops leaks. Resistant to teak cleaners, oil, diesel fuel and salt water. Adheres tenaciously without primers to fiberglass, glass, plastic, metal and wood. Simple clean up with mineral spirits. Not recommended for wooden deck seams or use in areas subject to gasoline.Features: Twists, bends, expands, compresses Seals ports, bed hardware and stops leaks Perfect for trim tabs and transducers WARNING: This product can expose you to chemicals including Toluene which is known to the State of California to cause birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less

Large Swingback Back Boat Seat Cover - Vinyl WhiteKeep your seats and consoles from cracking and fading! Boat seat and consolecovers are designed to protect your seats from damaging ultra-violet rays,wind, mildew and water. All Covers fold easily for storage and keep yourseats cool and clean!Dimensions: 36"H x 40"W x 20"DFeatures: Mildew and water repellant UV Protection Waterproof Air vents Heavy duty Drawstring hem Specifications: Color: White Cover Type: Seat Box Dimensions: 4"H x 10"W x 14"L WT: 2.6 lbs UPC: 040011114853

Read more less

Helm/Bucket/Fixed Back Boat Seat Cover - Vinyl WhiteKeep your seats and consoles from cracking and fading! Boat seat and consolecovers are designed to protect your seats from damaging ultra-violet rays,wind, mildew and water. All Covers fold easily for storage and keep yourseats cool and clean!Dimensions: 24"H x 24"W x 22"DFeatures: Mildew and water repellant UV Protection Waterproof Air vents Heavy duty Drawstring hem Specifications: Color: White Cover Type: Seat Box Dimensions: 3"H x 10"W x 14"L WT: 1.4 lbs UPC: 040011114839

Read more less

One Step Fiberglass Restorer & WaxDeep cleans and restores color to dirty or oxidized fiberglass or painted finishes11 oz. (325 ml), PasteA heavy duty cleaner and wax that works without the grueling effort or effects of highly abrasive rubbing compounds. Deep cleans and restores color to dirty or oxidized fiberglass or painted finishes. Follow up with a coat of Miracle Coat Boat wax to seal the lustre. Specifications: Type: Waxes & Polishes Box Dimensions: 2"H x 4"W x 4"L WT: 0.8 lbs UPC: 898286002203

Read more less

Hull Anode Type 15 - ZincFor sailing on salt water or brackish water, we recommend the use of zinc anodes. Cathodic protection by means of anodes is a ”must” for the protection of all metal parts under water. Therefore, not only for steel boats, but also for wooden, fibreglass, and aluminium hulls, anodes are required. The material of VETUS zinc anodes is of the highest possible standard, the U.S. mil.-A-18001 K. specifications. Anodes that do not meet these specifications have little or no effect at all.All VETUS anodes are streamlined and mounted either with specially made studs, which can be welded to a steel hull, or special through-hull bolts for fibreglass and wooden boats. Specifications: Material: Zinc Type anode: Hull Type of contour: Rectangular Weight (kg): 1.1 Length (mm): 150 Height (mm): 25 Specifications: Material: Zinc Box Dimensions: 1"H x 6"W x 9"L WT: 2 lbs UPC: 8717372280832

Read more less

TD Snap-On - Double Standard MaterialThe double material Snap-On features twice the material of the standard TD Snap-On. Use to quickly dry smooth surfaces streak-free. Easily connect and remove from your attachment pole with a quick snap. Pair with our Palm Beach Pole or any handle with a snap function. Specifications: Type: Tools & Accessories Box Dimensions: 2"H x 5"W x 19"L WT: 0.6 lbs UPC: 850005213062

Read more less

Palm Beach Reach (4-6 Feet) Carbon Fiber Extension HandleUpgrade your maintenance game with Palm Beach Reach, TD Mop’s new royal blue carbon fiber extension handle. Designed for effortless reach and precision, this ultra-lightweight handle is compatible with TD Mop snap-on mops and brushes.Features: Feather-Light & Strong – Crafted from premium carbon fiber, it delivers durability without the extra weight. The smaller handle is 16 ounces, and the longer handle is 24 ounces Easy Locking System – Clear guidelines ensure a secure, adjustable fit every time. Two Versatile Sizes – Choose from 4 to 6 feet or 6 to 10 feet for the perfect reach. Scratch-Free Cleaning – The deluxe finish helps prevent dings and damage to surfaces. Whether you're tackling boats, cars, or RVs, Palm Beach Reach gives you the power to clean smarter—not harder. Specifications: Type: Tools & Accessories Box Dimensions: 1"H x 1"W x 46"L WT: 1.05 lbs UPC: 850005213475

Read more less