75WR-1 Crows Foot Transducer WrenchTransducer wrenches are available for all bronze low profile transducers. They are used to facilitate holding of the transducer and tightening of the hull nut. Wrenches are constructed of 3/16" thick mild steel. They can easily be bent or modified to accommodate challenging installation locations. For use with: B75 SS75 Specifications: Type: Tools Box Dimensions: 1"H x 4"W x 5"L WT: 0.55 lbs

Read more less

75WR-4 Transducer Housing WrenchA single-handed wrench that holds the main thru-hull housing via the 'wrench flats' on the side of the housing to facilitate tightening of the hull nut. Use wrench 75WR-2 or 75WR-3 for the hull nut.For use with: B75 SS75 Specifications: Type: Tools Box Dimensions: 1"H x 5"W x 10"L WT: 0.6 lbs

Read more less

Transducer Pigtail, 10-Pin(F), 2 MetersWARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Type: Adapters Box Dimensions: 2"H x 6"W x 6"L WT: 0.3 lbs UPC: 801769003505

Read more less

8-Pin Female to Wire Block AdapterGarmin's adapter allows you to connect the wires on legacy 6-pin transducers with newer sonar that requires an 8-pin connection.WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Type: Adapters Box Dimensions: 3"H x 7"W x 7"L WT: 0.8 lbs UPC: 753759976286 Owner's Manual (pdf)

Read more less

Furuno 10-Pin Mix & Match Cable for 600W Non-CHIRP TransducersMix and Match 600W transducers are made as a common base transducer with a short (2m) cable attached, plus an interchangeable longer (8m) brand-specific adapter cable. The short pigtail attached to the transducer ends in an Airmar 5-pin male connector. The adapter cables have a matching Airmar 5-pin female connector at one end and the correct connector for a specific electronics brand at the other end.Both parts are needed for installation. If the user changes equipment brand later, the transducer can be left in place and the adapter cable replaced.*600W Mix and Match cables cannot be used with 1kw transducers or CHIRP transducers.Features: 10-Pin For Furuno 10-Pin equipment Specifications: Type: Adapters Box Dimensions: 2"H x 7"W x 7"L WT: 1.2 lbs UPC: 801769003611

Read more less

60WR-2 Transducer Hull Nut WrenchA single-handed wrench to tighten the hull nut on 2" bronze and stainless steel housings. You can use wrench 60WR-4 to brace the housing when using this wrench.For use with: B60 SS60 Specifications: Type: Tools Box Dimensions: 1"H x 5"W x 9"L WT: 0.55 lbs

Read more less

60WR-1 Crows Foot Transducer WrenchTransducer wrenches are available for all bronze low profile transducers. They are used to facilitate holding of the transducer and tightening of the hull nut. Wrenches are constructed of 3/16" thick mild steel. They can easily be bent or modified to accommodate challenging installation locations. For use with: SS60 B60 Specifications: Type: Tools Box Dimensions: 1"H x 4"W x 5"L WT: 0.5 lbs

Read more less

4-Pin Transducer to 8-Pin Sonar PortConnect a 4-pin transducer to an 8-pin sonar port on your compatible marine device with this adapter cable.WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Type: Adapters Box Dimensions: 1"H x 4"W x 5"L WT: 0.1 lbs UPC: 753759197810

Read more less

Suction Cup Transducer AdapterUsing your fishfinder as a portable unit? Use this suction cup adapter to attach your transom mount transducer to the side of your boat. WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Type: Adapters Box Dimensions: 3"H x 5"W x 7"L WT: 0.25 lbs UPC: 753759023768

Read more less

8-Pin Transducer to 12-Pin Sounder Adapter Cable w/XIDUse this adapter cable to connect an 8-pin transducer with XID to a 12-pin sonar port on a compatible marine device.WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Type: Adapters Box Dimensions: 1"H x 4"W x 7"L WT: 0.2 lbs UPC: 753759136345

Read more less

EC M10 Transducer Extension Cable - 10'10' extension cable for transducers. Current Models:  ICE HELIX, ICE Flashers, PiranhaMAX, HELIX 5, HELIX 7, HELIX 9, HELIX 10, HELIX 12Discontinued Series: 500 Series, 600 Series, 700 Series, 800 Series, 900 Series, 1100 SeriesLength: 10'WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Type: Extension Box Dimensions: 2"H x 8"W x 9"L WT: 0.8 lbs UPC: 082324050350

Read more less

12-Pin Pigtail Cable for TZT3Furuno's 12-Pin Pigtail Cable specifically for TZT3.This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns. Specifications: Type: Adapters Box Dimensions: 2"H x 5"W x 6"L WT: 0.5 lbs UPC: 611679391315

Read more less

RealVision 3D Transducer Extension Cable - 5M(16')RealVision 3D Transducer Extension Cables work with both the transom mounted RV-100, as well as through-hull RV-200 and RV-300 series transducers.  Each extension cable features a waterproof, twist-lock connector at the MFD end, and a compatible socket at the transducer end.  For best performance, Raymarine recommends using no more than two (2) extension cables in any given cable run. Specifications: Type: Extension Box Dimensions: 2"H x 10"W x 10"L WT: 1.5 lbs UPC: 723193817087

Read more less

12-Pin XDR Extension Cable - 10MFeatures: Extension Cable For Furuno Transducer 10M (33' Length) 12-Pin Color: Black This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns. Specifications: Type: Extension Box Dimensions: 4"H x 9"W x 12"L WT: 2.25 lbs UPC: 611679398840

Read more less

Replacement Top Mount f/HDI 83/200/455/800 TMReplacement mount for Skimmer and top housing Specifications: Type: Mounting Brackets Box Dimensions: 2"H x 3"W x 7"L WT: 0.23 lbs UPC: 421945359518

Read more less

LSS-2 HD Skimmer Mounting Bracket - Stainless SteelMounting bracket for LSS-2 StructureScan HD transducer.Specifications:Stainless Steel Specifications: Type: Mounting Brackets Box Dimensions: 2"H x 7"W x 13"L WT: 0.95 lbs UPC: 9420024123751

Read more less

Locking Collar Kit for RealVision 25-PinRaymarine Spare RealVision 25-pin locking collar kit

Read more less

CPT-DV/CPT-DVS Mounting KitTransom Mount Bracket for CPT-DV & CPT-DVS Specifications: Type: Mounting Brackets Box Dimensions: 2"H x 6"W x 8"L WT: 0.2 lbs UPC: 723193795842

Read more less

Mounting hardware for the XNT transom mount transducers. Includes a kick up bracket.WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Type: Mounting Brackets Box Dimensions: 2"H x 8"W x 9"L WT: 0.45 lbs UPC: 082324507779 Owner's Manual (pdf)

Read more less

AD XTM 9Transducer Mounting HardwareThis hardware kit adapts to our standard transom mount transducers in the list below for use on the trolling motor.For use with:XNT 9 20 TXNT 9 QB 90 TXNT 9 SI 180 TXNT 9 QB 90XNT 9 20XNT 9 DI T1157c1158c1158c DI141C161323325343C345c345c DI363365i383C385ci385ci DI515525535550560561565570570 DI575580581i585C586C586c HD587CI587ci HD595C596C596c HD596c HD DI597CI597ci HD597ci HD DI717718727728737747c767768777c2778C778c HD787c2787c2I788C788ci788ci HD788ci HD DI798c SI798ci SI798ci HD SI858c858c DI917C957958c958c DI981C SIHDR 610MATRIX 10MATRIX 12MATRIX 15MATRIX 17MATRIX 20MATRIX 25MATRIX 27MATRIX 35MATRIX 37MATRIX 55MATRIX 65MATRIX 67MATRIX 77CMATRIX 87CMATRIX 97PIRANHA 1PIRANHA 2PIRANHA 3PIRANHA 4PIRANHA 5PiranhaMax 10PiranhaMax 15PiranhaMax 150PiranhaMax 160PiranhaMax 170PiranhaMax 180PiranhaMax 190CPiranhaMax 20PiranhaMax 210PiranhaMax 215PiranhaMax 220PiranhaMax 230PiranhaMax 240PiranhaMax 30WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Type: Adapters Box Dimensions: 2"H x 7"W x 9"L WT: 0.5 lbs UPC: 082324507724 Owner's Manual (pdf)

Read more less

117WR-3 Double Handle Transducer WrenchTransducer wrenches are available for all bronze low profile transducers. They are used to facilitate holding of the transducer and tightening of the hull nut. Wrenches are constructed of 3/16" thick mild steel. They can easily be bent or modified to accommodate challenging installation locations. For use with: B117 B150 B744V B744VL B765C SS555 Specifications: Type: Tools Box Dimensions: 4"H x 5"W x 6"L WT: 0.85 lbs

Read more less

Humminbird 14-Pin Mix & Match Chirp Cable - 1MAirmar's 14-Pin Mix & Match Chirp Cable for HumminbirdFeatures: Length: 1M 14-Pin Specifically for Humminbird This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns. Specifications: Type: Adapters Box Dimensions: 2"H x 5"W x 5"L WT: 0.2 lbs UPC: 801769003284

Read more less

Raymarine 11-Pin High or Med Mix & Match Transducer CHIRP Cable for CP470 Airmar MMC-11R CHIRP Mix and Match Transducer Cable 1M Raymarine 11-Pin.For use with Airmar's High or Med Single Band Mix and Match CHIRP transducers up to 1kW (1,000 watt).This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns. Specifications: Type: Adapters Box Dimensions: 1"H x 6"W x 8"L WT: 0.25 lbs UPC: 801769003369

Read more less

ActiveTarget 2 XL Recon Trolling Motor MountFeatures: Optional mount for ActiveTarget® 2 XL Transducer Compatible with all Recon trolling motors Utilizes the ActiveTarget® mounting attachment points on the Recon lower unit Trouble-free adjustment between Forward/Down XL and two Scout XL positions (Scout XL Shallow & Scout XL Deep) with clear alignment indicators for each position 0-degree offset in Forward/Down XL position for effortless bait tracking In the Box: Recon motor mount sub-assembly Cable routing arm Coiled tubing Assembly hardware Specifications: Type: Mounting Brackets Box Dimensions: 7"H x 7"W x 8"L WT: 3.3 lbs UPC: 9420064139439

Read more less

117WR-4 Transducer Housing WrenchA single-handed wrench that holds the main thru-hull housing via the 'wrench flats' on the side of the housing to facilitate tightening of the hull nut. For 2" bronze and stainless steel housings (P617V, B617V, SS617V).Use wrench 117WR-2 or 117WR-3 for the hull nut.*Note that this wrench will not fit on the CA500 camera housing. Specifications: Type: Tools Box Dimensions: 1"H x 3"W x 8"L WT: 0.45 lbs

Read more less

MM-HB Mix & Match™ Cable 5-Pin 600W Series with Humminbird #9 Connector - 9MSpecifications: Sensor Connector: MM Display Connector: HB Mix and Match Series: 5-Pin 600 Watt Country of Origin: USA Cable-Length: 9 m (30') Specifications: Type: Adapters Box Dimensions: 1"H x 5"W x 8"L WT: 0.4 lbs UPC: 801769003772

Read more less

MM-9N Mix & Match Cable for Simrad XSONIC Non-CHIRP TransducersMix and Match 600W transducers are made as a common base transducer with a short (2m) cable attached, plus an interchangeable longer (8m) brand-specific adapter cable. The short pigtail attached to the transducer ends in an Airmar 5-pin male connector. The adapter cables have a matching Airmar 5-pin female connector at one end and the correct connector for a specific electronics brand at the other end.Both parts are needed for installation. If the user changes equipment brand later, the transducer can be left in place and the adapter cable replaced.*600W Mix and Match cables cannot be used with 1kw transducers or CHIRP transducers.Features: Connector: 9-pin, Depth only Fits: HDS Carbon, evo 3 This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns. Specifications: Type: Adapters Box Dimensions: 2"H x 8"W x 8"L WT: 1.3 lbs UPC: 801769003321

Read more less

Furuno 12-Pin Mix & Match Cable for CHIRP Dual Element TransducersFor use with Airmar's Mix and Match CHIRP transducers up to 1kW (1,000 watts).This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns. Specifications: Type: Adapters Box Dimensions: 1"H x 8"W x 8"L WT: 0.3 lbs UPC: 801769002720

Read more less

Deadrise Angle Finder - Accuracy of ± 1/2°Accurate to 1/2 of 1°, this precision instrument, with strong ceramic magnet is designed for attachment to a carpenter's square or straight edge to overcome time consuming computation of angles.Features: Quickly measures boat hull deadrise angle. Ball Bearing construction for accuracy. Attach to straight edge or framing square Handy angle and grade chart on back of unit Specifications: Type: Tools Box Dimensions: 2"H x 5"W x 8"L WT: 0.5 lbs UPC: 038987110061

Read more less

60WR-4 Transducer Housing WrenchA single-handed wrench that holds the main thru-hull housing via the 'wrench flats' on the side of the housing to facilitate tightening of the hull nut.Use wrench 60WR-2 or 60WR-3 for the hull nut.For use with: B60 SS60 Specifications: Type: Tools Box Dimensions: 0"H x 6"W x 9"L WT: 0.51 lbs

Read more less

6-Pin Female to 8-Pin Male AdapterThis adapter allows you to connect newer 8-pin transducers to devices that require a 6-pin connector.WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns. Specifications: Type: Adapters Box Dimensions: 1"H x 4"W x 4"L WT: 0.2 lbs UPC: 753759976279

Read more less

Transom Mount Bracket f/Livescope Plus LVS34Easily attach your compatible LiveScope™ transducer to the transom of your boat with this stainless steel mount. Specifications: Type: Mounting Brackets Box Dimensions: 3"H x 7"W x 7"L WT: 2.56 lbs UPC: 753759298517

Read more less

EC M30 Transducer Extension Cable - 30'30' extension cable for transducers. Current Models:  ICE HELIX, ICE Flashers, PiranhaMAX, HELIX 5, HELIX 7, HELIX 9, HELIX 10, HELIX 12Discontinued Series: 500 Series, 600 Series, 700 Series, 800 Series, 900 Series, 1100 SeriesLength: 30'WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Type: Extension Box Dimensions: 4"H x 8"W x 9"L WT: 1.4 lbs UPC: 082324050367

Read more less

Transom Mounting Bracket for P66 Transducer - 2004 & upThis product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns. Specifications: Type: Mounting Brackets Box Dimensions: 2"H x 3"W x 4"L WT: 0.2 lbs UPC: 801769004656

Read more less

175WR-4 Transducer Housing WrenchA single-handed wrench that holds the main thru-hull housing via the 'wrench flats' on the top of the housing to facilitate tightening of the hull nut. Use wrench 164WR-2 or 164WR-3 for the hull nut.For use with: B164 B175 SS164 SS264 IMPORTANT: the design of the housing for these transducers changed slightly in June 2012. This wrench is for the newer design and has an internal width of 2-3/4". If you need a wrench for the older designs then use the 164WR-4 instead, with an internal width of 2-7/16". Specifications: Type: Tools Box Dimensions: 1"H x 5"W x 10"L WT: 0.6 lbs

Read more less

Transducer Extension CableUse this 10' (3M) extension cable to connect your 4-pin transducer to your sonar unit.Compatible Devices: echo™ 100 echo™ 150 echo™ 200 echo™ 300c echo™ 500c echo™ 550c WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Type: Extension Box Dimensions: 1"H x 5"W x 5"L WT: 0.27 lbs UPC: 753759980009

Read more less

ActiveTarget™ Trolling Motor Shaft MountAttach an ActiveTarget™ transducer to the shaft of your trolling motor with the trolling motor shaft mount for Forward, Down and Scout views.

Read more less

xSonic Pigtail Wiring Block AdapterConnect transducer with NO connector to echo sounder requiring a 9-Pin connector. Specifications: Type: Adapters Box Dimensions: 4"H x 6"W x 8"L WT: 1.2 lbs UPC: 9420024154618

Read more less

Forward-Facing Motorized Sonar MountThe FORESIGHT Forward-Facing Sonar Mount is the most sophisticated mounting system on the market. It allows the sonar transducer to stow and deploy with the bow-mount trolling motor but still be controlled independently.*The FORESIGHT was designed to be used with a 0-degree transducer mounting bracket. The use of perspective mounts and other add-ons that move the transducer further away from the Foresight shaft may cause the transducer to contact the trolling motor.Features:The wireless foot pedal is includedSpecifications: Weight: 12 lbs. Dimensions: 39 × 10 × 5 inches Fit kit: Lowrance Ghost, Garmin Force, and Minn Kota Ultrex (Kits not included) Specifications: Type: Mounting Brackets Box Dimensions: 5"H x 10"W x 39"L WT: 11.5 lbs UPC: 854127007912

Read more less

164WR-1 Crows Foot Transducer WrenchTransducer wrenches are available for all bronze low profile transducers. They are used to facilitate holding of the transducer and tightening of the hull nut. Wrenches are constructed of 3/16" thick mild steel. They can easily be bent or modified to accommodate challenging installation locations. For use with: B164 SS164 B175C SS164 Specifications: Type: Tools Box Dimensions: 1"H x 6"W x 7"L WT: 0.95 lbs

Read more less

9 M SILR Y Dual Side Image Transducer Adapter Cable f/HELIX Y Cable - Separates Side Imaging into Left and Right Side Beams - for Side Imaging products only.  Allows the use of two side imaging transducers with one unit without the need for a transducer switch.  Y Cable - Separates Side Imaging into Left and Right Side Beams - for Side Imaging products only.  Allows the use of two side imaging transducers with one unit without the need for a transducer switch.  Used in applications where the a plastic thru the hull transducer is required on a boat with a deep V hull or the motor or other items on the transom of the boat may block one side of the transducer and distort readings.    30" length. Supports MEGA Side Imaging. WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Type: Adapters Box Dimensions: 2"H x 7"W x 9"L WT: 0.4 lbs UPC: 082324052378

Read more less

Heavy-Duty Transom Mount Bracket w/Spray ShieldMount the transducer on the transom of your boat so it remains in the water at all times to provide excellent sonar returns.  Bracket can be adjusted to allow the angle of the transducer to be parallel with the water surface.The spray shield blocks excessive water from spraying off the transducer when the boat is running at high speeds.  Creates minimal drag on the boat.Compatible with: 4-Pin, 8-Pin or 12-Pin scanning transducersWARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Type: Mounting Brackets Box Dimensions: 3"H x 3"W x 7"L WT: 0.4 lbs UPC: 753759171636

Read more less

Foulfree Transducer Coating Formulated by industry-leading scientists and certified by Airmar for transducers.   Fouling on the face of transducers can reduce their sensitivity, bottom-echo returns and positive fish targets.  It can also increase the turbulence over the face of the transducer causing aeration and loss of bottom contact.  Foulfree keeps transducers clean and operating at the top of their game for the clearest sonar images possible.  The proprietary clear coat forms a slick surface that marine growth can’t grab onto, keeping your transducer surface clean and clear. Features: Foulfree™ is simple to apply and lasts for 12-24 months Transducer safe - Airmar certifies that Foulfree™ coating on its transducers results in no loss in transducer performance Biocide Free - Foul-release, not antifoul.  Foul-release coatings use physical means to reduce fouling, creating a surface that’s tough for marine organisms to adhere to Easy to apply A foul-free transducer equals more clarity, detail, and visibility below the waterline. Technical Specifications: Coverage Rate - 1ft² (two (2) average size transducers) In the Box: Abrasive pad XDclean wipe XDprime, wipe Applicator brush Foulfree Clear coat - 15ml *Sold as an IndividualThis product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns. Specifications: Type: Service Kits Box Dimensions: 2"H x 2"W x 5"L WT: 0.15 lbs UPC: 9421903335425 Quick Guide (pdf)

Read more less

9-Pin Black to 7-Pin Blue Adapter Cable for Non-CHIRP TransducersConnects a non-CHIRP transducer with a 9-pin black connector to the older 7-pin blue sockets on displays and echosounder modules. For use with transducers that have an analog temperature sensor.

Read more less

0 Degree Pole Mount f/Livescope Plus LVS34Position your LiveScope™ Plus LVS34 transducer on this 0-degree pole mount for an optimal viewing angle while ice fishing (works for open water fishing too).

Read more less

0 Degree Livescope Pole MountPosition your Panoptix LiveScope™ LVS32 transducer on this 0 degree pole mount for an optimal viewing angle while ice fishing (works for open water fishing too).

Read more less

Transducer Spray ShieldGarmin's transducer spray shield is available for Garmin side scanning transducers.Mounting hardware included.WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Type: Mounting Brackets Box Dimensions: 1"H x 3"W x 7"L WT: 0.2 lbs UPC: 753759148256

Read more less

ActiveTarget™ Forward/Down Mounting KitAttach an ActiveTarget transducer to your trolling motor with the Trolling Motor Forward/Down Mount for Forward and Down views at the trolling motor.

Read more less