1500 G.P.H. Automatic Bilge PumpHigh pumping capacity and reliability at a lower cost. The Rule 1500 offers more pumping capacity and more exclusive design features than any comparable competitive pump. 1-1/8" (28.6mm) discharge outlet. 12 Volts DC unless noted.Features: Computerized operation - no float switch required 3 wire version allows manual override or indicator light capability Fully Submersible Easy clean snap lock strainer Silent and vibrationless operation Anti-airlock protection Compact, efficient long life motor Ignition protected No burn-out when run dry Rust and Corrosion protection Used by leading boatbuilders worldwide marine grade blocked wiring WARNING: This product can expose you to chemicals including FORMALDEHYDE (GAS) which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov. Specifications: Gallons Per Hour: 1500 GPH Operation: Automatic Outlet Size: 1-1/8" Volts: 12v Type: Electric Box Dimensions: 7"H x 8"W x 11"L WT: 4.45 lbs UPC: 042237084965 Owner's Manual (pdf)

Read more less

Water Puppy (US)Features: Small bilge debris present no problem to these bronze bodied, flexible impeller pumps Simple design means fewer wearing parts ISO 8846 MARINE (Ignition protection) ISO 8849 MARINE (Bilge pump standard) Flow rate: 23.8 Litres/min (6.3 USgallons/min) Self-priming from dry up to 1.2m (4ft) Body: Bronze Impeller: Neoprene Seal: Lip type Voltage: 12 Vdc Amp Draw: 8 amp Fuse Size: 15 amp Motor: Permanent magnet type, fully enclosed, stainless steel shaft. Adapter for 3/4" External Garden Hose Thread included Weight: 4-1/2 lb WARNING: This product can expose you to chemicals including NICKEL (METALLIC) which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov. Specifications: Gallons Per Hour: 378 GPH Gallons Per Minute: 6.3 GPM Outlet Size: 1" Volts: 12v Type: Electric Box Dimensions: 4"H x 6"W x 10"L WT: 5.85 lbs UPC: 671880532112 Owner's Manual (pdf)

Read more less

17820 Oil Changer SystemThe Jabsco Oil Change System is designed to be installed in a vessel's engine room with its manifold and valves permanently plumbed to the vessel's engines' oil pans or transmissions' oil sumps. The manifold is factory fitted with three ball valves to serve three different oil reservoirs and may be fitted with two additional ball valves to drain up to five oil reservoirs. The system can be used to remove old oil from an engine or transmission then reversed, with the integral reversing switch, to pump a measured amount of new oil back into the engine or transmission. Each connection to an engine is controlled by a dedicated full flow ball valve. The system's cover provides an attractive appearance, fully shrouding the entire pump and manifold system. It also provides added protection against accidental draining of an engine's oil supply because the valve cover protects the factory supplied valves from being accidentally bumped open. Additionally, at the end of an oil change, the cover will not close unless the factory supplied valves are in the fully closed position.WARNING: This product can expose you to chemicals including NICKEL (METALLIC) which is known to the State of California to cause cancer, and LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Volts: 12v Box Dimensions: 8"H x 12"W x 12"L WT: 10.95 lbs UPC: 671880529624 Owner's Manual (pdf)

Read more less

58541-1000 Pulley & Belt Kit Kit contains small and Large pulley, belt and clip.Compatible With:58500 Series Lite Flush Toilets*Sold as an Individual  Specifications: Type: Service Kits Box Dimensions: 1"H x 4"W x 6"L WT: 0.5 lbs UPC: 671880616874

Read more less

Par-Max 2 Water Pressure Pump - 24V - 2 GPM - 35 PSIHD (Heavy Duty) models include a wider diameter motor with a powder coated shell, cast aluminum endbells and lower housing to improve pressure capability and life. Available in configurations up to 6 GPM (23 LPM) and 60 PSI (4.1 BAR), these pumps deliver exceptional performance. Standard models provide good performance in an economical footprint. These configurations are available in 1-3 GPM, perfect for vessels with 1-3 outlets. A plastic housing protects the motors on these units from corrosion. Features: Co-molded diaphragm technology for long life and durability HD models feature heavy duty, motors and cast aluminum lower housings which allow for longlife, even at high pressures Efficient and quiet operation Integrated, sealed pressure switch for on-demand operation Self-priming allows for installation versatility Can run dry without damage Quick connect ports for ease of installation, servicing, and maintenance Vibration dampening mounting feet Equipped with integrated bypass module to reduce cycling and provide smoother flow Specifications: Motor design: Brushed, permanent magnet TENV  Pumphead upper housing material: Glass fiber reinforced polypropylene  Diaphragm: Co-molded TPV  Check valves: EPDM  Max inlet pressure: 30 PSI (2.1 Bar)  Fluid temperature range: 32°F – 140°F (0°C – 60°C)  Dry self-priming capability: 7ft min (2.13m/min)  Certifications: CE, ISO8846, RCM Ingress Protection: IPX6 WARNING: This product can expose you to chemicals including ANTIMONY OXIDE (ANTIMONY TRIOXIDE) which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov. Specifications: Volts: 24v Max PSI: 35 Gallons Per Minute: 2 GPM Box Dimensions: 5"H x 6"W x 15"L WT: 4.5 lbs UPC: 671880841771 Brochure (pdf)

Read more less

Tsunami Mk2 T500 Aerator KitThis aerator kit is recommended for fishing boats with built-in livewells that are not equipped with a thru-hull recirculation system. The pump is sealed and can be occasionally submerged; however, the electrical wires must never be submerged.Kit Includes: Aerator spray head SS wire mesh strainer  Pump Straight outlet fitting  Hose  Two hose clamps Specifications: Pump Model: T500 Flow Gal/HR: 500 Amp Fuse: 3 Outlet Hose Inner Diameter: 3/4” (19mm) Two hose clamps Specifications: Gallons Per Hour: 500 Outlet Size: 3/4" Volts: 13.6v Box Dimensions: 5"H x 7"W x 9"L WT: 1.15 lbs UPC: 022697026019

Read more less

1" Electro-Magnetic Clutch PumpFlow rate: Nominal 23 US Gallons/min at 1750 RPMSelf-priming from dry up to 7.8ftFeatures: Constructed from marine quality bronze and stainless steel for ruggedness and reliability. Easy to service and maintain. Inexpensive to buy and operate. Will tolerate abrasive wear (this may affect performance - seek advice from your distributor). Handles hard and soft solids without clogging. Can pump in either direction. Will not airlock. APPLICATIONS MARINE:Engine cooling, Pumping bilges, Wash downs, Circulating water in bait tanks, Utility dockside pump.INDUSTRIAL:Circulating and transferring, Velocity mixing, Return spill, Sump drainage, Chemicals, Pharmaceuticals, Soap, Liquors, Ink, Dyes, Alcohol, Tanning Liquors, Glycerin, Brine, etc.FARMING:Pumping water for stock, Pumping water from shallow wells and cisterns.PUBLIC UTILITIES AND MUNICIPALITIES:Under the hood mounting on service trucks for dewatering and draining meter boxes, manholes, excavations, and truck installation under hood for emergency pumping.WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Gallons Per Minute: 23 GPM Volts: 12v Box Dimensions: 8"H x 9"W x 14"L WT: 16.15 lbs UPC: 671880007962 Owner's Manual (pdf)

Read more less

PH & PHII Universal Repair KitThese universal repair kits service all PH/PHII Raritan heads manufactured between 1960 and the present. It replaces kits PHRK, PHRKII, and PHRKIIC.In the Box: (2) 1201  (2) 1202 (1) 1203B1  (2) 1203B2  (1) 1203B3  (1) 1213A  (1) 1213B  (1) 1213C  (1) 1213D  (1) 1214 (1) 1214A  (1) 1214B  (4) 1226C (1) 1226CA  (1) 1232MS  (1) 1234 (1) 25103 (1) 25105  (1) C253  (4) RNI (3) SLICC WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Quick Guide (pdf)

Read more less

WP008 Water Pump Repair Kit for Honda Outboard EnginesThis water pump repair kit is designed for specific Honda outboard engines.Fits:Honda BF175/200/225 Outboard EnginesReplaces: Honda Water Pump Repair Kit 06192-ZY3-000 SIERRA Water Pump Repair Kit 18-3285 EMP Water Pump Repair Kit 46-46620 Warranty InformationWhen properly installed, all ARCO products are warrantied against defects in materials and workmanship for 12 months for leisure use and 90 days for commercial or racing applications.Add an extra year of warranty to your rotating electric ARCO product (Tilt/Trim Motors, Alternators, Outboard Starters, and Inboard Starters) when you register your product within 30 days of purchase. You can register your product by visiting arcomarine.com/product-registration.This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Read more less

WP007 Water Pump Repair Kit for Suzuki Outboard EnginesThis water pump repair kit is designed for specific Suzuki outboard engines.Fits:Suzuki DF 60/70 (1998-07), DT90/100 (1989-01) Outboard EnginesReplaces: SUZUKI Water Pump Repair Kit 17400-87E04 SUZUKI Water Pump Repair Kit 17400-87E03 SUZUKI Water Pump Repair Kit 17400-87E02 SUZUKI Water Pump Repair Kit 17400-87E01 SUZUKI Water Pump Repair Kit 17400-87E00 SIERRA Water Pump Repair Kit 18-3254 EMP Water Pump Repair Kit 46-46418  Warranty InformationWhen properly installed, all ARCO products are warrantied against defects in materials and workmanship for 12 months for leisure use and 90 days for commercial or racing applications.Add an extra year of warranty to your rotating electric ARCO product (Tilt/Trim Motors, Alternators, Outboard Starters, and Inboard Starters) when you register your product within 30 days of purchase. You can register your product by visiting arcomarine.com/product-registration.This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Read more less

WP006 Water Pump Repair Kit for Suzuki Outboard EnginesThis water pump repair kit is designed for specific Suzuki outboard engines.Fits:Suzuki DF 90/115/140 (2001-06) Outboard EnginesReplaces: SUZUKI Water Pump Repair Kit 17400-90J20 SUZUKI Water Pump Repair Kit 17400-90J11 SUZUKI Water Pump Repair Kit 17400-90J10 SUZUKI Water Pump Repair Kit 17400-90J01 SUZUKI Water Pump Repair Kit 17400-90J00 JOHNSON / EVINRUDE OMC Water Pump Repair Kit 5033541 JOHNSON / EVINRUDE OMC Water Pump Repair Kit 0778241 JOHNSON / EVINRUDE OMC Water Pump Repair Kit 5033541 SIERRA Water Pump Repair Kit 18-3258 Warranty InformationWhen properly installed, all ARCO products are warrantied against defects in materials and workmanship for 12 months for leisure use and 90 days for commercial or racing applications.Add an extra year of warranty to your rotating electric ARCO product (Tilt/Trim Motors, Alternators, Outboard Starters, and Inboard Starters) when you register your product within 30 days of purchase. You can register your product by visiting arcomarine.com/product-registration.This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Read more less

Brass Baitwell Plug - 3/4" Cam action nitrile rubber plug snaps shut to form a leak-proof seal for livewells and baitwells. Clockwise turn of the handle tightens the plug, brass lever snaps down to lock. Snap lock handle is adjustable to tighten plug size to fit most bait wells currently available.WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less

Brass Baitwell Plug - 5/8" Cam action nitrile rubber plug snaps shut to form a leak-proof seal for livewells and baitwells. Clockwise turn of the handle tightens the plug, brass lever snaps down to lock. Snap lock handle is adjustable to tighten plug size to fit most bait wells currently available.WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less

Brass Baitwell Plug - 1/2" Cam action nitrile rubber plug snaps shut to form a leak-proof seal for livewells and baitwells. Clockwise turn of the handle tightens the plug, brass lever snaps down to lock. Snap lock handle is adjustable to tighten plug size to fit most bait wells currently available.WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less

Brass Baitwell Plug - 3/8" Cam action nitrile rubber plug snaps shut to form a leak-proof seal for livewells and baitwells. Clockwise turn of the handle tightens the plug, brass lever snaps down to lock. Snap lock handle is adjustable to tighten plug size to fit most bait wells currently available. WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less

Atlantes Freedom™The Atlantes was one of the first toilets to incorporate the idea of having all components mounted within the bowl. The idea behind the Atlantes was to offer a metal handle on the side of the bowl to make the marine bathroom less intimidating for those not used to being on a boat. We offer the metal handle with many options but most people understand they simply need to push it to have the toilet flush. The head area of any boat can be very daunting for those not familiar with how the toilets work. By offering a handle on the side of the bowl your guests will feel more at ease. The other, and probably equally important, feature of the original Atlantes was to appeal to the women on the boat. The Atlantes is far more aesthetically appealing than tons of nooks and crannies which ultimately means the toilet looks much cleaner. Users in any bathroom can appreciate the smooth minimal lines to make cleaning a quick and easy chore.Today the Atlantes now incorporates the same Vortex-Vac technology as the Marine Elegance but in a bowl that offers a more substantial footprint as well as the just like home handle option. The advantage of the Vortex-Vac technology is that the waste is efficiently moved from the bowl by a vacuum action created by the pump rather than depending on remote vacuum generation. While a vacuum toilet may use slightly less water, the advantage of Vortex-Vac is that one does not need to depend on the vacuum generator pump that tends to run for about 45 seconds to generate the vacuum. The timed flush cycle brings water in then runs a discharge then water again and discharge for the least amount of water usage and effectiveness of moving waste out of the toilet. Standard Features: One piece china bowl Anti-clog "power shred" discharge system Household style Stainless handle with smart toilet control Remote intake pump Powerful bronze cutting blades designed to "shred" most objects Benefits: Vortex-Vac technology Simple flexible installation Low power consumption Three modes of operation - Fill, dry flush or fill and flush Freedom from clogged toilets and marine size bowls, excellent performance even in commercial applications Easy to clean and maintain Diaphragm intake pump can be run dry Microprocessor control and solid state circuit breaker No fuses or relays inside the unit Easily installs above or below waterline on any vessel The Raritan Programmable Smart Toilet Control:The Raritan Smart Toilet Control is a fully programmable flush control. The control allows users to flush the toilet with no water, a small amount of water or a fully timed flush. the timed flush feature can be adjusted on the panel without having to remove any components. Normal Flush - starts a timed flush, walk away and the toilet will run through a sequence of intake and discharge modes ensuring maximum bowl rinse, bowl re-fills to leave water in the bow Water Saver - starts a timed flush using half of the water of a normal flush. Bowl refills to leave water in the bowl. Water Only - adds additional water to the bowl without discharging any of the contents of the bowl. Allows the user to wet the bowl prior to use or fill the bowl to a certain level to minimize water usage. Empty Only - allows the user to evacuate the bowl while using no water. While the button is pressed the discharge pump will run, when released the pump stops. WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Color: White Gallons Per Minute: 3 GPM Inlet Size: 3/4" Operation Method: Electric Outlet Size: 1-1/2" Rinse Water: RAW Suction Lift (ft.): 4' Volts: 12v Type: Toilet Size: Household Size Box Dimensions: 19"H x 19"W x 26"L WT: 60 lbs UPC: 085462029226 Quick Guide (pdf)Owner's Manual (pdf)Brochure (pdf)

Read more less

EvoFlex2 25' Lightweight RV/Marine Drinking Water Hose - Fabric Reinforced - 5/8" IDCamco’s EvoFlex2 25-Foot Drinking Water Hose with a 5/8-inch inner diameter is ideal for RV and marine use. The tough polyester outer fabric helps maintain the hose's shape and protects it from breaks, cracks, and leaks. This product features aluminum fittings with a molded strain relief. It is drinking water safe and has a lead-free, BPA-free, and phthalate-free formulation. The hose leaves no strong plastic taste in your water. When not in use, this extra flexible hose is compact and easy to store—perfect for tight spaces. Includes a storage bag.Features: Extra Flexible Design: Extra flexible hose is ideal for RV and marine use. A tough polyester outer fabric helps maintain the hose's shape and protect it from breaks, cracks, and leaks The Perfect Size Hose: 25-foot hose with 5/8-inch diameter Drinking-Water Safe: Contains a BPA-free, lead-free, and phthalate-free formulation Provides Great Tasting Water: The hose won't leave a strong plastic taste in your water Durable Construction: Features aluminum fittings with a molded strain relief Easy to Store: Hose is compact for simple storage—perfect for tight spaces; includes a storage bag

Read more less

Stainless Steel Hose Barb Thru-Hull Fitting - 3/4" Features: NPS Thread With Hose Connection #316 Stainless Steel UL Listed 647B Specifications: Hose Size: 3/4" Material: Stainless Steel Box Dimensions: 3"H x 3"W x 4"L WT: 0.5 lbs UPC: 742985138988

Read more less

Bronze Pipe Nipple - 1-1/4" NPT Features: Cast-in wrench flat simplifies installation and removal NPT x NPT Connection C83600 Bronze   Full flow   Note-C83600 bronze fittings are not in compliance with NSF-61 and therefore are not intended for use in potable water systems. Specifications: Construction: Bronze Box Dimensions: 2"H x 2"W x 3"L WT: 0.68 lbs UPC: 742985143661

Read more less

Replacement Belt Kit for Lite FlushSpecifications: 9mm Drive Belt Packaged Dimensions: L:5.00 x H:5.00 x W:5.00cm Actual Weight: 0.10 Kg  (Approx. 0.30 Kg packed)

Read more less

Rule 3700Heavy duty construction for both commercial and pleasure boat use; known for trouble free operation and reliability. 1-1/2" (38mm) discharge outlet. 12 Volts DC unless noted.Features: Fully Submersible Easy clean snap lock strainer Silent and vibrationless operation Anti-airlock protection Compact, efficient long life motor Ignition protected No burn-out when run dry Rust and Corrosion protection Used by leading boatbuilders worldwide marine grade blocked wiring Specifications Voltage: 12 Vdc Amp Draw: 15.5 amp Fuse Size: 25 amp Height: 7 1/4 inches 184 mm Width: 4 7/8 Inches 124 mm Weight: 5-4 lb 2.4 kg Warranty: 5 years <WARNING: This product can expose you to chemicals including FORMALDEHYDE (GAS) which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov. Specifications: Gallons Per Hour: 3700 GPH Operation: Non-Automatic Outlet Size: 1-1/2" Volts: 12v Type: Electric Box Dimensions: 7"H x 8"W x 11"L WT: 6.05 lbs UPC: 042237085818 Owner's Manual (pdf)

Read more less

Mag Drive Centrifugal Pump - 21GPM - 110V ACDesigned for applications that require a safe and leak free, continuous duty pump. Great for marine air conditioning circulation, Ice Makers, Hot water circulation, Livewell and Bait tank installations.Pump Head is manufactured in chemical resistant thermo-plastics - entirely non-metallic.UL listed, ignition and thermally protected fan cooled motor.Features: 21.13 GPM open Flow 110V AC 60Hz 3/4" NPT ports for easy connection 18 foot head WARNING: This product can expose you to chemicals including NICKEL (METALLIC) which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov. Specifications: Volts: 110v Gallons Per Minute: 21 GPM Box Dimensions: 7"H x 10"W x 11"L WT: 7.7 lbs UPC: 671880624299 Quick Guide (pdf)

Read more less

Gas Fill w/ Locking Cap for 1-1/2" Hose(0599) Chrome Plated Zinc Alloy Flange Black Plastic Body Black Plastic Cap w/ Strap Grounding Screw Included Cap Retainer and Gasket Locking Cap has a cover for the key hole Tech Info for Hose Size: 1-1/2" O.D. Flange: 3-1/8" Length of Neck: 3-1/8" Mounting Hole Dia.: 2-1/8" Screw Size: #8 Quick Guide (pdf)

Read more less

Par-Max HD6 Heavy Duty Water Pressure Pump - 12V - 6 GPM - 40 PSIHD (Heavy Duty) models include a wider diameter motor with a powder coated shell, cast aluminum endbells and lower housing to improve pressure capability and life. Available in configurations up to 6 GPM (23 LPM) and 60 PSI (4.1 BAR), these pumps deliver exceptional performance. Standard models provide good performance in an economical footprint. These configurations are available in 1-3 GPM, perfect for vessels with 1-3 outlets. A plastic housing protects the motors on these units from corrosion. Features: Co-molded diaphragm technology for long life and durability HD models feature heavy duty, motors and cast aluminum lower housings which allow for longlife, even at high pressures Efficient and quiet operation Integrated, sealed pressure switch for on-demand operation Self-priming allows for installation versatility Can run dry without damage Quick connect ports for ease of installation, servicing, and maintenance Vibration dampening mounting feet Equipped with integrated bypass module to reduce cycling and provide smoother flow Specifications: Motor design: Brushed, permanent magnet TENV  Pumphead upper housing material: Glass fiber reinforced polypropylene  Diaphragm: Co-molded TPV  Check valves: EPDM  Max inlet pressure: 30 PSI (2.1 Bar)  Fluid temperature range: 32°F – 140°F (0°C – 60°C)  Dry self-priming capability: 7ft min (2.13m/min)  Certifications: CE, ISO8846, RCM Ingress Protection: IPX6 WARNING: This product can expose you to chemicals including ANTIMONY OXIDE (ANTIMONY TRIOXIDE) which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov. Specifications: Volts: 12v Max PSI: 40 Gallons Per Minute: 6 GPM Box Dimensions: 6"H x 6"W x 15"L WT: 9 lbs UPC: 671880841979 Brochure (pdf)

Read more less

LoPro 900GPH Bilge Pump - Non-AutomaticThe Rule LoPro™ 900 non-automatic is a low profile Bilge Pump with a 900 gallons per hour capacity. Designed for tight spaces, the height of the pump is only 2-1/4".It features a threaded discharge nozzle to which you can attach either a straight or a 90° fitting (included). In addition, you may use the tricuspid check valve {included} on the straight fitting to minimize the back flow of water. The entire discharge body swivels up to 180° for ease of installation. The hose attached can also swivel 360° to route the hose perfectly. Features: 900 GPH Low Profile Bilge Pump Fits into hard to reach places Non-automatic, requires float and or panel switch to automate Threaded discharge ports with mulitiple fittings available Features a tricuspid check valve to minimize back flow of water WARNING: This product can expose you to chemicals including STYRENE which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov. Specifications: Volts: 12v Operation: Non-Automatic Gallons Per Minute: 15 GPM Gallons Per Hour: 900 GPH Type: Electric Box Dimensions: 4"H x 8"W x 10"L WT: 1.5 lbs UPC: 042237114365 Brochure (pdf)

Read more less

MegaPress 316 FKM 3/4" 90 Degree ElbowFeatures: For use with Sch. 5 to Sch. 40 stainless steel pipe 316 stainless steel Press connection Components:FKM sealing elements, grip rings, separator rings Specifications: Construction: Stainless Steel Box Dimensions: 1"H x 1"W x 4"L WT: 0.4 lbs

Read more less

MegaPress 316 FKM Tee - 2" x 2" x 2"Features: For use with Sch. 5 to Sch. 40 stainless steel pipe 316 stainless steel Press connection Components:FKM sealing elements, grip rings, separator rings Specifications: Construction: Stainless Steel Box Dimensions: 3"H x 6"W x 8"L WT: 2.6 lbs

Read more less

MegaPress 316 FKM 2" Coupling with StopFeatures: For use with Sch. 5 to Sch. 40 stainless steel pipe 316 stainless steel Press connection Components:FKM sealing elements, grip rings, separator rings Specifications: Construction: Stainless Steel Box Dimensions: 3"H x 3"W x 5"L WT: 1.3 lbs

Read more less

MegaPress 316 FKM 3/4" CapFeatures: For use with Sch. 5 to Sch. 40 stainless steel pipe 316 stainless steel Press connection Components:FKM sealing element, grip ring, separator ring Specifications: Construction: Stainless Steel Box Dimensions: 2"H x 2"W x 3"L WT: 0.3 lbs

Read more less

SuperSwitch™ Float SwitchNow backed by a 5 year warranty, the non-mercury SuperSwitch is designed for the toughest applications. Design includes marine grade 14 gauge blocked wire, larger float for increased buoyancy, removable base for easy servicing and a snap switch design capable of handling pumps drawing up to 20 Amps.WARNING: This product can expose you to chemicals including STYRENE which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov. Specifications: Volts: 12/24/36v Type: Switches Box Dimensions: 3"H x 6"W x 8"L WT: 0.4 lbs UPC: 042237095497 Owner's Manual (pdf)

Read more less

MegaPress 316 FKM 1-1/4" UnionFeatures: For use with Sch. 5 to Sch. 40 stainless steel pipe 316 stainless steel Press connection Components:AFM flat gasket, FKM sealing elements, grip rings, separator rings Specifications: Construction: Stainless Steel Box Dimensions: 2"H x 2"W x 7"L WT: 2.5 lbs

Read more less

Mini Accumulator TankPart #: 30573-0003This accumulator tank is intended for installation in any pumped water system controlled by a pressure switch, and may also be used with air-driven pumps. The tank can serve as a storage vessel as well as a pulsation dampener for pressurized fluid. The accumulator tank smoothes water flow and reduces on/off switch cycling of the pump by lessening the variation in pressure and flow between the pump and the system discharge points.The even flow of water gives better control of hot water temperature with systems using instant water heaters.Features: Internal bladder Smoother flow Quieter water system Longer pump life Easily fitted to new or existing systems Compact size Quick-connect/disconnect port flttings Mounting point for optional pressure switch Food grade materials, NSF Standard 18 listed Volume: 21.5 oz Dimensions: 8.4 x 4.7 inches Max Pressure: 125 psi Weight: 0.96 lb Pre charged pressure: 10 psiWARNING: This product can expose you to chemicals including NICKEL (METALLIC) which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov. Specifications: Type: Accumulator/Pressure Tanks Box Dimensions: 5"H x 8"W x 12"L WT: 1.35 lbs UPC: 671880582834 Brochure (pdf)

Read more less

HotShot HD5 Heavy Duty Washdown Pump Kit with 25' HoseCoil - 12V - 5GPM - 70PSIYears of clean decks and satisfaction in the form of robust and reliable high-flow and high-pressure diaphragm pumps. The Jabsco legacy of exceptional products continues with this updated and improved lineup of washdown pumps and kits. HD (heavy-duty) models include a wider diameter motor with a powder-coated shell, cast aluminum endbells, and lower housing to improve pressure capability and life. Standard models provide exceptional performance in an economical footprint. A plastic housing protects the motors from corrosion. Features: Co-molded diaphragm technology for long life and durability HD models feature heavy-duty, motors and cast aluminum lower housings which allow for long life, even at high pressures Efficient and quiet operation Integrated, sealed pressure switch for on-demand operation Self-priming allows for installation versatility Can run dry without damage Quick connect ports for ease of installation, servicing, and maintenance Vibration dampening mounting feet Full kit versions are available which include a 25' (7.6m) HoseCoil Specifications: Motor design: Brushed, permanent magnet TENV  Pumphead upper housing material: Glass fiber reinforced polypropylene  Diaphragm: Co-molded TPV  Check valves: EPDM  Max inlet pressure: 30 PSI (2.1 Bar)  Fluid temperature range: 32°F – 140°F (0°C – 60°C)  Dry self-priming capability: 7ft min (2.1m min)  Certifications: CE, ISO8846, RCM  Ingress protection: IPX6 Fittings & Accessories: Quick Connect straight hose barb and GHT fittings 90° 20 mesh Quick Connect strainer Trigger nozzle & Quick Connect hose adapters

Read more less

500GPH Standard Bilge Pump - 24VCustomers talk about flow, they want the water out of the bilge, andfast. Improved design and performance means that our next generation 500GPH pump will produce this flow at just 24V rather than 27.2V as previously required...more typical of on board voltage supply.Our next generation of Rule pumps include check valves and to do this, we've created hidden air vent to prevent airlocking. Under each strainer tab there is a small hole that vents any air trapped in the pump housing preventing airlocks...and that's how we do it.We have true electromagnetic suppression (EMC). We have a built-in thermal cell that protects the pump and the vessel when things get too hot.We've re-engineered the inside and outside of our bilge pumps, starting with a blank slate. And we're just getting startedFeatures: Non-automatic - used with a panel switch or Rule float switch Submersible and Ignition Protected High efficiency, low amp motor Stainless-steel shaft Includes backflow preventer WARNING: This product can expose you to chemicals including 1,3-Butadiene which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Type: Electric Gallons Per Hour: 500 GPH Operation: Non-Automatic Outlet Size: 3/4" Volts: 24v Box Dimensions: 4"H x 7"W x 7"L WT: 0.8 lbs UPC: 042237104748 Brochure (pdf)

Read more less

MegaPress 316 FKM 1" CapFeatures: For use with Sch. 5 to Sch. 40 stainless steel pipe 316 stainless steel Press connection Components:FKM sealing element, grip ring, separator ring Specifications: Construction: Stainless Steel Box Dimensions: 2"H x 2"W x 3"L WT: 0.5 lbs

Read more less

1-1/8" Heavy Duty PVC Bilge & Livewell Hose (FDA) - Clear with Black Helix - Sold by the FootTrident Smooth extra heavy wall vinyl (FDA) well hose. All clear (see thru) with black helix. Excellent durability, flexibility & bend radius for XHD bilge, live well, drain, scupper lines, etc. No cuffs are required. Features: Sold by the foot Flexible, but the 147 series is less flexible than the 149 series of hoses Application:Bilge and live well hoseSpecifications: Tube & Cover: Clear vinyl reinforced with black helix  Color: Clear with black helix Reinforcement: PVC Helix Temperature Range: 10°F-120°F (-12°C-49°C)  Inner Diameter: (inch) 1-1/8" / (mm) 28.6 Outer Diameter: (inch) 1.39" / (mm) 35.4 Working Pressure: (Psi Vac In./Hg) 28 Weight: (Lb./ 50 ft.) 15 / (Kg/m) 0.45 Bend Radius: (inch) 3.5" / (mm) 8.9 *Burst Pressure is 4 x Working PressureThis product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns. Specifications: ID Diameter (inches): 1-1/8" Length (Feet): Sold By The Foot Box Dimensions: 2"H x 2"W x 2"L WT: 0.28 lbs Quick Guide (pdf)

Read more less

High Flow Dual Pump System - 24 VDC - 10.0 GPMThe most advanced system available. This fully-automatic, quiet unit delivers water smoothly and consistently.Features: Replaces 5907 System Delivers up to 10 GPM at Open Flow Includes the AQUA KING II Supreme 5.0 Pump and PRO BLASTER II Ultimate 5.0 Pump 24 VDC 55 PSI Shut-off Pressure Built to Withstand the Harsh Marine Environment with Electro-Coated Motor, O-ring Seals and Fully-Sealed Wire Entries This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns. Specifications: Volts: 24v Max PSI: 55 Gallons Per Minute: 10 GPM Box Dimensions: 7"H x 7"W x 24"L WT: 16.1 lbs

Read more less

MegaPress 316 FKM 1-1/2" Coupling with StopFeatures: For use with Sch. 5 to Sch. 40 stainless steel pipe 316 stainless steel Press connection Components:FKM sealing elements, grip rings, separator rings Specifications: Construction: Stainless Steel Box Dimensions: 3"H x 3"W x 5"L WT: 1 lbs

Read more less

Shower Drain Box with 800 GPH Pump - 24VThis compact, full-capacity shower drain system provides 800 GPH (3028 LPH) of output. Activated by a float switch, it turns on as the tank fills and shuts off when it’s empty. It has three inlet ports that offer varying combinations for the inlet hose, as well as a quick-release tank lid and an easy-clean internal strainer. Specifications: Type: Shower Drains Gallons Per Hour: 800 GPH Volts: 24v Box Dimensions: 6"H x 10"W x 14"L WT: 4.2 lbs UPC: 042237106568

Read more less

DC 150 CFM Flangemount 3" BlowersFeatures: Tough Reinforced Plastic Housing Mount to any surface Slip-On Inlet and Outlet Ducting Connection Efficient High Volume Air Flow Low Current Draw Corrosion-Resistant Materials Throughout N.M.M.A. Type Accepted DC Models comply with USCG Regulation 183.410 and ISO 8846 MARINE for Ignition Protection DC Models comply with Complies with ISO 9097 MARINE WARNING: This product can expose you to chemicals including NICKEL (METALLIC) which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov. Specifications: Ducting: 3" Open Flow (CFM): 150 CFM Volts: 24v Box Dimensions: 6"H x 8"W x 9"L WT: 4.2 lbs UPC: 671880029377 Owner's Manual (pdf)

Read more less

MegaPress 316 FKM 1-1/2" UnionFeatures: For use with Sch. 5 to Sch. 40 stainless steel pipe 316 stainless steel Press connection Components:AFM flat gasket, FKM sealing elements, grip rings, separator rings Specifications: Construction: Stainless Steel Box Dimensions: 3"H x 3"W x 7"L WT: 2.5 lbs

Read more less

MegaPress 316 FKM Tee - 1-1/2" x 1-1/2" x 1-1/2"Features: For use with Sch. 5 to Sch. 40 stainless steel pipe 316 stainless steel Press connection Components:FKM sealing elements, grip rings, separator rings Specifications: Construction: Stainless Steel Box Dimensions: 3"H x 5"W x 7"L WT: 1.9 lbs

Read more less

MegaPress 316 FKM 1-1/4" CapFeatures: For use with Sch. 5 to Sch. 40 stainless steel pipe 316 stainless steel Press connection Components:FKM sealing element, grip ring, separator ring Specifications: Construction: Stainless Steel Box Dimensions: 3"H x 3"W x 3"L WT: 0.6 lbs

Read more less

MegaPress 316 FKM 2" CapFeatures: For use with Sch. 5 to Sch. 40 stainless steel pipe 316 stainless steel Press connection Components:FKM sealing element, grip ring, separator ring Specifications: Construction: Stainless Steel Box Dimensions: 3"H x 3"W x 3"L WT: 0.95 lbs

Read more less

MegaPress 316 FKM 1-1/2" CapFeatures: For use with Sch. 5 to Sch. 40 stainless steel pipe 316 stainless steel Press connection Components:FKM sealing element, grip ring, separator ring Specifications: Construction: Stainless Steel Box Dimensions: 3"H x 3"W x 3"L WT: 0.7 lbs

Read more less

MegaPress 316 FKM 3/4" UnionFeatures: For use with Sch. 5 to Sch. 40 stainless steel pipe 316 stainless steel Press connection Components:AFM flat gasket, FKM sealing elements, grip rings, separator rings Specifications: Construction: Stainless Steel Box Dimensions: 2"H x 2"W x 5"L WT: 1.05 lbs

Read more less

MegaPress 316 FKM Reducer - 1-1/2" x 1-1/4"Features: For use with Sch. 5 to Sch. 40 stainless steel pipe 316 stainless steel Press connection Components:FKM sealing elements, grip rings, separator rings Specifications: Construction: Stainless Steel Box Dimensions: 2"H x 2"W x 5"L WT: 1.1 lbs

Read more less

MegaPress 316 FKM Tee - 1" x 1" x 1"Features: For use with Sch. 5 to Sch. 40 stainless steel pipe 316 stainless steel Press connection Components:FKM sealing elements, grip rings, separator rings Specifications: Construction: Stainless Steel Box Dimensions: 2"H x 3"W x 5"L WT: 1 lbs

Read more less