24-12-3 DC ConverterConvert 17-32 VDC input to 12 VDC negative ground output for powering communication and navigation equipment on negative ground systems. (See Isolated Series for positive ground applications.)Features: Excellent Regulation: Output voltage maintained within 1% under all line and load conditions within the rating The heat generated by semi-conductors is extracted and dissipated by large heat sink fins that maximize air contact for cool operation and the long life of components Polyurethane conformal coating on PC boards and corrosion-resistant anodized aluminum cases with heavy-duty shock mounts assure survival in hostile environments Numerous Converter and Load Protection Circuits: Current limiting Automatic thermal shutdown Short circuit proof Reverse polarity Overvoltage protection Carries CE mark Specifications: Input Voltage: 17-32 Output Voltage: 13.6 Output Amps (Intermittent): 3 Output Amps (Continuous): 3 Case Size (H x W x D): 3.5 x 3.5 x 1.75 inches (8.9 x 8.9 x 4.5 centimeters) Weight: 1 lb. (.45 kg) Output: 13.6 VDC (internally adjustable 12.6 -14.5)  Ripple: 150 mV P-P maximum Regulation: 1% Line/Load Switching Frequency: 40 kHz Efficiency: 85% – Typical. Isolation: Output/Chassis; Input/chassis: 250 VDC Duty Cycle Ratings*: Intermittent: 20 minutes max on time, 20% duty. current limit set at approx. 105% of intermittent rating. Continuous: 24 hours, 100% duty *24-12-3: 2-minute max. on time Idle Current: Less than 100 mA (including power “ON” light) Operating Temp Specifications: 0-50 degrees C, Derate Linearly From 100% @ 40 degrees C To 50% @ 50 degrees C. Thermal shutdown @ 70 degrees C Case Temperature Model 24-12-3: Full output -25 degrees to +30 degrees C; Derate linearly from 100% @ +30 degrees C to 45% @ +50 degrees C Mechanical Specifications: Powder-coated aluminum heat sink case Front panel terminal block Heavy-duty mounting flange Conformal coated PC board Options:Operation as battery charger or parallel redundant operation* – derate to continuous duty rating (contact factory)This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Read more less

SS Switch - 3 AC Selector SwitchThis AC source selector switch is an essential item for any vessel with an on-board AC generator and/or inverter. By isolating power source inputs, the switch eliminates the safety hazard and/or damage that can occur if two AC sources are applied to the same circuit simultaneously.The switch is fitted with a compact escutcheon plate with engraved switch position nomenclature.The switches carry cUL approval, are CE-marked, and feature heavy-duty contacts and a positive step cam mechanism for low-resistance contact closure. Features:May be rear-mounted in a panel with a thickness up to 1/4”Specifications: Amperage @ 115/230V: 30   Number of Poles: 2 Switch Positions: 2 + “OFF” Standard Plate Markings: SHIP-OFF-SHORE     Depth Dimensions: 2-1/8 in.

Read more less

AC-II PanelEssential control and protection whenever AC from shore power or generators is on board. A double-pole master breaker with a power-on indicator light protects both the hot and neutral legs of the AC circuit. A reverse polarity light provides a clear warning when wiring is reversed and poses a shock hazard.AC-II has a 30 Amp master breaker (15A or 50A* optional). Specifications: Cut-Out Dimensions: 4 x 2.5 inches (10.2 x 6.4 centimeters) Weight: 1 lb. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns. Specifications: Max Breaker Quantity: 5 Box Dimensions: 6"H x 7"W x 9"L WT: 1 lbs

Read more less

BB-8 Bus BarIdeal as a DC ground tie point or positive bus, this heavy-duty, 500-amp-rated bus bar assembly features 5/16 in. studs on 1 in. center in 1/4 in. thick copper bar for common connection or distribution of large wire gauges.Features: Accommodate 5/16" ring terminals Insulated base (reinforced nylon resin with a clear protective cover) Specifications: Quantity of 5/16" Studs: 8 Size (inches): 9-1/16” x 1-1/2”

Read more less

ACCY-IBX Blank PanelThis versatile panel is ideal when only a limited number of electrical circuits are needed or for larger systems where their modular design makes for an easy and attractive expansion of existing system capacity.Stock panels with breakers installed come standard with DC indicator lights but may be specially ordered with AC indicator lights. Blank versions of the panels have all the necessary hardware to install indicator lights and breakers. All panels are provided with a circuit identification label set of 22 common on-board electrical functions. ACCY-IBX is a blank version of ACCY-IX. No breakers or indicator lights are provided. Label set, indicator light, and breaker mounting hardware are provided.Specifications: Cut-Out Dimensions: 4 x 6 inches (10.2 x 15.2 centimeters) Weight: 1 lb.

Read more less

PC-25 Power Conditioner Noise FilterThe interference or electronic “noise” generated by alternators, ignition systems, motors, etc. can render a vehicle or vessel’s radio or other electronic equipment virtually useless. This interference takes the form of popping or static on radios or audio gear and garbled images or “hashes” on video displays.These specialized filters can be used singly or in combination to attenuate conducted line noise, either at the affected equipment or at the noise source.Features: Heavy-duty aluminum construction Operate on 6-48 VDC systems Integral mounting flanges for secure installation Nickle-plated, brass stud connectors on alternator filters accommodate high-current cables and terminals Color-coded wire leads on PC models make in-line installation easy Specifications: Filtered Frequencies: Audio – 200 MHz Rating: 25 amp Installation Location: At affected equipment in “+” and “-” leads     Dimensions (inches): 2 x 4.25 x 3.25 Weight (lbs): 2

Read more less

BB-2/8 Bus BarIdeal as a DC ground tie point or positive bus, this heavy-duty, 500-amp-rated bus bar assembly features 5/16 in. studs on 1 in. centers in 1/4 in. thick copper bar for common connection or distribution of large wire gauges.Features: Accommodate 5/16" ring terminals Insulated base (reinforced nylon resin with a clear protective cover) Specifications: Quantity of 5/16" Studs: 2 plus 8 – #8 screws Size (inches): 6-1/16” x 1-1/2”

Read more less

BX-3 Junction BoxThis BX Series splashproof box provides secure, protected wiring connections in wheelhouses or below decks and engine rooms. Features: IP rating 54 – “Splashproof” Rugged cast aluminum box with white enamel finish Metal box reduces electrical interference Easy wiring access through multiple grommeted cable entries Supplied with high-quality connector strips – secure wires with compression fittings – no terminals required – see matrix below for connector strips specifications per box Specifications: Number of Connector Strips: 2 Positions per Strip: 11 Max Wire Gauge: 14 Max Amps (per position): 10  Cable Entries: 2 Cable Diameter: 0.59 in. Box Size: 4.7 x 3.7 x 1.3 in. Box Size: 11.9 x 9.4 x 3.3 cm Specifications: Type: Junction Box Box Dimensions: 2"H x 5"W x 5"L WT: 0.68 lbs

Read more less

PC-10 Power Conditioner Noise FilterThe interference or electronic “noise” generated by alternators, ignition systems, motors, etc. can render a vehicle or vessel’s radio or other electronic equipment virtually useless. This interference takes the form of popping or static on radios or audio gear and garbled images or “hashes” on video displays.These specialized filters can be used singly or in combination to attenuate conducted line noise, either at the affected equipment or at the noise source.Features: Heavy-duty aluminum construction Operate on 6-48 VDC systems Integral mounting flanges for secure installation Nickle-plated, brass stud connectors on alternator filters accommodate high-current cables and terminals Color-coded wire leads on PC models make in-line installation easy Specifications: Filtered Frequencies: Audio – 200 MHz Rating: 10 amp Installation Location: At affected equipment in “+” and “-” leads     Dimensions (inches): 1.25 x 4.25 x 3 Weight (lbs): 1

Read more less

CCX-R Thru-Dex FittingThis waterproof fitting's entry hole is pre-drilled in seal with a slit edge allowing feed through of cable with a factory-installed connector attached. One CCX fitting is required for each cable.Features: Create a 100% waterproof seal when routing cables through decks and bulkheads Entry hole predrilled in seal with a slit to edge Allowing installation or removal with the connector still attached Rugged weatherproof nylon housing with neoprene seal Specifications: Cable Diameter Range (inches): .47-.59 Max Connector Diameter (inches): 1.57 Specifications: Type: Deck Seal Box Dimensions: 2"H x 4"W x 7"L WT: 0.2 lbs

Read more less

PX-3 Junction BoxThis waterproof junction box is ideal for making wiring connections above or below decks, even in areas subject to occasional spray.Connector Strips Installed in BoxesMolded nylon encases pairs of connectors that use screw compression to secure wires without the use of lugs. Ideal for electronic installations. Brass barrels capture wires and are held in place with a stainless steel “finger” compressed by a screw. The screw does not make contact with the wires, protecting the copper strands from cuts and breakage and meeting ABYC standards.Features: Similar to BX Series junction boxes but made from rugged, non-corrosive, high-impact polypropylene The snap-on cover provides a watertight seal “Universal” cut-to-fit graduated diameter cable entries accommodate a wide cable range Multiple position connector strips with “captive” screw compression wire terminals installed, see matrix below for connector strip specifications per box Multiple knockouts are provided for conduit access (in addition to cable entries) IEC Waterproof Rating: IP55 – “Water projected in jets against the enclosure from any direction shall have no harmful effects.” Specifications: Number of Connector Strips: 2 Positions per Strip: 9 Max Wire Gauge: 16 Number of Cable Entry Ports: 7 Number of Cable Entries Installed: 7 Spare Cable Entries Provided: 0 Cable Diameter Range (inches): .14 – .99 Cable Diameter Range (mm): 3.5 – 25.5 Box Size (inches): 4.45 x 4.45 x 2.29     Box Size (cm): 11.3 x 11.3 x 5.8 Specifications: Type: Junction Box Box Dimensions: 3"H x 7"W x 9"L WT: 0.5 lbs

Read more less

DX-3 Feed-Thru Waterproof FittingProvided with a solid neoprene cable gland, the installer drills holes and slits as required to accommodate cable with or without a factory-installed connector. Multiple cables may be passed through this single fitting.Features: Similar to CCX Series except the installer drills holes in the seal to accommodate cable(s) Multiple cables may be routed through a single-fitting Specifications: Drill-Thru Aperture: 1.65 in. Max. Connector Diameter: 1.65 in. Specifications: Type: Deck Seal Box Dimensions: 2"H x 4"W x 7"L WT: 0.2 lbs

Read more less

PA-30/20 Deck HornClear, distortion-free, waterproof deck horns are ideal for shipboard paging, hailing, fog horns, and alarm systems. high-impact plastic construction and assembled with stainless steel hardware. 8 Ohm.Specifications: Output Nominal/Peak: 30 watts or 20 watts Weight: 3 lbs. Specifications: Power - Output (Watts): 30w Box Dimensions: 6"H x 8"W x 10"L WT: 2.7 lbs Quick Guide (pdf)

Read more less

CCX-T Thru-Dex FittingThis waterproof fitting's entry hole is pre-drilled in seal with a slit edge allowing feed through of cable with a factory-installed connector attached. One CCX fitting is required for each cable.Features: Create a 100% waterproof seal when routing cables through decks and bulkheads Entry hole predrilled in seal with a slit to edge Allowing installation or removal with the connector still attached Rugged weatherproof nylon housing with neoprene seal Specifications: Cable Diameter Range (inches): .18-.35 Max Connector Diameter (inches): .83 Specifications: Type: Deck Seal Box Dimensions: 2"H x 4"W x 7"L WT: 0.2 lbs

Read more less

BX-2 Junction BoxThis BX Series splashproof box provides secure, protected wiring connections in wheelhouses or below decks and engine rooms. Features: IP rating 54 – “Splashproof” Rugged cast aluminum box with white enamel finish Metal box reduces electrical interference Easy wiring access through multiple grommeted cable entries Supplied with high-quality connector strips – secure wires with compression fittings – no terminals required – see matrix below for connector strips specifications per box Specifications: Number of Connector Strips: 1 Positions per Strip: 12 Max Wire Gauge: 16 Max Amps (per position): 6  Cable Entries: 8 Cable Diameter: 0.37 in. Box Size: 4.4 x 2.4 x 1.2 in. Box Size: 11.2 x 6.1 x 3.1 cm Specifications: Type: Junction Box Box Dimensions: 2"H x 4"W x 8"L WT: 0.45 lbs

Read more less

CCX-S Thru-Dex FittingThis waterproof fitting's entry hole is pre-drilled in seal with a slit edge allowing feed through of cable with a factory-installed connector attached. One CCX fitting is required for each cable.Features: Create a 100% waterproof seal when routing cables through decks and bulkheads Entry hole predrilled in seal with a slit to edge Allowing installation or removal with the connector still attached Rugged weatherproof nylon housing with neoprene seal Specifications: Cable Diameter Range (inches): .35-.55 Max Connector Diameter (inches): .83 Specifications: Type: Deck Seal Box Dimensions: 1"H x 4"W x 7"L WT: 0.2 lbs

Read more less

BX-1 Junction BoxThis BX Series splashproof box provides secure, protected wiring connections in wheelhouses or below decks and engine rooms. Features: IP rating 54 – “Splashproof” Rugged cast aluminum box with white enamel finish Metal box reduces electrical interference Easy wiring access through multiple grommeted cable entries Supplied with high-quality connector strips – secure wires with compression fittings – no terminals required – see matrix below for connector strips specifications per box Specifications: Number of Connector Strips: 1 Positions per Strip: 6 Max Wire Gauge: 16 Max Amps (per position): 6  Cable Entries: 2  Cable Diameter: 0.25 in. Box Size: 2 x 2 x 1.2 in. Box Size: 5.1 x 5.1 x 3.1 cm Specifications: Type: Junction Box Box Dimensions: 2"H x 4"W x 6"L WT: 0.35 lbs

Read more less

PX-2 Junction BoxThis waterproof junction box is ideal for making wiring connections above or below decks, even in areas subject to occasional spray.Connector Strips Installed in BoxesMolded nylon encases pairs of connectors that use screw compression to secure wires without the use of lugs. Ideal for electronic installations. Brass barrels capture wires and are held in place with a stainless steel “finger” compressed by a screw. The screw does not make contact with the wires, protecting the copper strands from cuts and breakage and meeting ABYC standards.Features: Similar to BX Series junction boxes but made from rugged, non-corrosive, high-impact polypropylene The snap-on cover provides a watertight seal “Universal” cut-to-fit graduated diameter cable entries accommodate a wide cable range Multiple position connector strips with “captive” screw compression wire terminals installed, see matrix below for connector strip specifications per box Multiple knockouts are provided for conduit access (in addition to cable entries) IEC Waterproof Rating: IP55 – “Water projected in jets against the enclosure from any direction shall have no harmful effects.” Specifications: Number of Connector Strips: 2 Positions per Strip: 6 Max Wire Gauge: 16 Number of Cable Entry Ports: 7 Number of Cable Entries Installed: 7 Spare Cable Entries Provided: 0 Cable Diameter Range (inches): .14 – .81 Cable Diameter Range (mm): 3.5 – 20.5     Box Size (inches): 3.35 x 3.35 x 1.66     Box Size (cm): 8.5 x 8.5 x 4.2 Specifications: Type: Junction Box Box Dimensions: 2"H x 6"W x 8"L WT: 0.15 lbs

Read more less

PX-1 Junction BoxThis waterproof junction box is ideal for making wiring connections above or below decks, even in areas subject to occasional spray.Connector Strips Installed in BoxesMolded nylon encases pairs of connectors that use screw compression to secure wires without the use of lugs. Ideal for electronic installations. Brass barrels capture wires and are held in place with a stainless steel “finger” compressed by a screw. The screw does not make contact with the wires, protecting the copper strands from cuts and breakage and meeting ABYC standards.Features: Similar to BX Series junction boxes but made from rugged, non-corrosive, high-impact polypropylene The snap-on cover provides a watertight seal “Universal” cut-to-fit graduated diameter cable entries accommodate a wide cable range Multiple position connector strips with “captive” screw compression wire terminals installed, see matrix below for connector strip specifications per box Multiple knockouts are provided for conduit access (in addition to cable entries) IEC Waterproof Rating: IP55 – “Water projected in jets against the enclosure from any direction shall have no harmful effects.” Specifications: Number of Connector Strips: 1 Positions per Strip: 6 Max Wire Gauge: 16 Number of Cable Entry Ports: 5 Number of Cable Entries Installed: 3 Spare Cable Entries Provided: 2 Cable Diameter Range (inches): .14 – .81 Cable Diameter Range (mm): 3.5 – 20.5     Box Size (inches): 2.95 x 2.95 x 1.66     Box Size (cm): 7.5 x 7.5 x 4.2 Specifications: Type: Junction Box Box Dimensions: 3"H x 6"W x 8"L WT: 0.2 lbs

Read more less