Search results for "radar mounts"

Small Offset Trolling Motor Plate for Garmin KrakenThe Sea Brackets Small Offset Trolling Motor Mounting Plate, designed for the Garmin Quick Release Plate System, offers a robust and reliable solution for installing any Force Kraken Trolling motor. Crafted from 6061 T6 aluminum, each plate is primed, powder-coated, and UV-protected for exceptional durability against the elements. Whether for port or starboard installation, these plates boast clean, accurately gauged holes for seamless bolt engagement.Suggested Hardware: 316L stainless steel hardware is recommended for rust prevention Mounting hardware is included with Garmin's Quick Release Plate System Backing disk from Sea Brackets or an alternative backing support system 1/4–20 flat-head Phillips machine screws, fender washers, and lock nuts 5/16–18 Flat-head Phillips machine screws, fender washers, and lock nuts Dimensions:18.5" x 13.5" x 1/2"Note: Hardware length is dependent on the thickness of the hull, backing hardware, and other various components.

Read more less

Large Offset Trolling Motor Plate for Minn Kota QuestThe Sea Brackets Large Offset Trolling Motor Mounting Plate, designed for Minn Kota’s RTA-55 or RTA-83 Quick Release Bracket, offers a robust and reliable solution for installing any Quest Series Trolling motor. Crafted from 6061 T6 aluminum, each plate is primed, powder-coated, and UV-protected for exceptional durability against the elements. Whether for port or starboard installation, these plates boast clean, accurately gauged holes for seamless bolt engagement.Suggested Hardware: 316L stainless steel hardware is recommended for rust prevention Mounting hardware is included with Minn Kota’s RTA-55/RTA-83 Quick Release Bracket Backing disk from Sea Brackets or an alternative backing support system 1/4–20 tapered Phillips machine screws, fender washers, and lock nuts 3/8–16 Flathead Phillips machine screws, fender washers, and lock nuts Note: Hardware length is dependent on the thickness of the hull, backing hardware, and other various components.

Read more less

444 Compact Threaded Deck MountFits gunnels up to 2" thick. Secures with no exposed hardware using provided nylon nut.Comes with cap to seal the bottomWARNING: This product can expose you to chemicals including Diisononyl Phthalate (DINP) which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov.

Read more less

244 Flush Deck MountWith splash coverFor all Scotty post mount rod holdersDimensions 4" x 2" x 2"Bolting Dimensions 1 5/16" x 3 3/16"WARNING: This product can expose you to chemicals including Diisononyl Phthalate (DINP) which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov.

Read more less

3' Stainless VHF Whip 3dB with Bracket for Sailboats - No CableThe KM-3A antenna is developed for sailing boats. It combines lightness and flexibility due to the quality stainless steel whip. Its elegant style fits perfectly with the boat design.The antenna is supplied together with a stainless steel mounting bracket, which makes the installation quick and stable.Features: Electropolished stainless steel whip Extra flexible SO 239 waterproof connector Mounting bracket supplied with the antenna Specifications: Frequency: 156-162 MHz Impedance: 50 ohms Electrical length: 1/2 λ V.S.W.R.: < 1,5:1 Polarization: Vertical Gain: 3 dB Max power input: 50 W DC ground: Yes Whip material: Stainless Steel Connector: SO 239 Mounting: Stainless steel bracket Length: 1,0 m (3.3′) Weight: 0,23 kilo

Read more less

Sidekick™ Mounting PlateThe Sidekick™ Mounting Plate is designed to work in conjunction with the exclusive Sidekick WiFi Sonar Transducer. The mounting plate can be mounted to the wall, floor, or countertop of your wheel house, making accessibility quick and easy. Built-in teeth help to manage your transducer cord when mounted vertically, and the cut-out allows your transducer cord to pass through the plate when mounted horizontally. Just snap the Sidekick module into the designated slot on the mounting plate, drop your transducer in the hole, and start fishing.Features: Mounting plate Exclusive Sidekick compatibility Cable management teeth Cable pass-through Durable and lightweight ABS material

Read more less

Simrad HS65 GNSS Compass with Flat MountModel: 000-16235-001  Heading accuracy without the restriction of magnetic interference to account for. Heading Accuracy of <2° RMS 10Hz ideal for Autopilot and MARPA applications. *<90seconds cold start Dead Reckoning for heading up 3 minutes following loss of satellite data. Position <1 Meter 10Hz Pitch/Roll Accuracy <1.5° RMS Sleek design Backup magnetic compass with <3° RMS** Heave <30CM RMS Supports GPS, GLONASS, Galileo, BEIDOU, QZSS1 Constellation options with SBAS Options for Flush, Raised or Pole mount 640mm/2ft NMEA2000 Fly-lead Low profile mounting adaptor for various installation types. Low Profile Pole Mount  Specifications  GNSS Constellations ​ GPS, GLONASS, Galileo, BeiDou, QZSS​ SBAS tracking 2-channel, parallel tracking (WAAS, EGNOS, Position accuracy (no SBAS)​ 1.5 m RMS (no SBAS) Heading accuracy, static/dynamic (RMS) ​ <2° (RMS)​ Heading dead reckoning (DR) deviation per minute​ 2°/min​ (up to 3 minutes) Pitch/roll accuracy, static/dynamic (RMS)​ 1.5° (RMS) ​ Heading accuracy, magnetic post 3 min DR ​ <±3° TRUE Heave accuracy, dynamic (RMS)​ 30cm ​ Update rate​ 10Hz​ Rate of turn 500°/s maximum Time to position fix 25 s typical Time to Heading Fix (GNSS) 10 s typical (after you have valid position) Compass safe distance 0.5 m Power Input voltage 9—16 V DC Power consumption 1.6 W (multi-GNSS, typical continuous draw at 12 V) Load equivalency number (LEN) 3 Power isolation Isolated to enclosure Reverse polarity protection Yes Connector NMEA 2000® Micro C Other Weight (no mount) 0.85 kg (1.87 lb) Operating temperature —25°C to + 70°C (—13°F to +158°F) Enclosure IPX6 and IPX7  What's in the Box: HS-65 Compass NMEA2000 T-Joiner Flat Mount

Read more less

Transom Mounting Bracket for P66 Transducer - 2004 & upThis product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns. Specifications: Type: Mounting Brackets Box Dimensions: 2"H x 4"W x 4"L WT: 0.21 lbs UPC: 801769004656

Read more less

icom M510BB Black Box VHF with HM195GW White CommandMicModel: M510 BB GW 21 USAIcom's M510BB is perfect for boats that need AIS receive functionality without taking up precious helm space. The supplied CommandMicTM provides all the safety and communication functions for commercial and leisure boaters.The M510BB consists of a CommandMicTM and black box RF unit. Use the CommandMicTM for all operations including DSC. Install the RF unit out of sight, place up to 60 ft (18.3 m)* away from the CommandMicTM.Add up to two additional CommandMicTM microphones for boats requiring two or three comms stations. Extend communication points around the boat including the cockpit, fly bridge, and tower. Access the intercom functions for one-to-all or one-to-one communications on the boat.The M510BB includes an integrated AIS receiver, perfect for remote station information via the CommandMicTM, or integrated into the NMEA 2000(R) bus to display radar and chart plotter information on an MFD (Multi-Function Display).In addition to the conveniently located DSC button on the back of every CommandMicTM, the M510BB introduces a dedicated DSC Remote Control (EN 300 338-8 compatible) terminal, allowing a connection to an external device to centralize emergency communications control.The M510BB has a last call voice recording function automatically saves up to two minutes of an incoming call.The NMEA 2000(R) network provides plug-and-play data communication to inter-connect other marine equipment such as an MFD (Multi-Function Display). The radio can send AIS, GNSS (GPS) position, DSC call, and radio channels to other equipment.On the back of every CommandMicTM is a conveniently located DSC button. Once triggered, the M510BB transmits a DSC alert signal to nearby vessels with the MMSI* and GPS location of your vessel. *MMSI number must be obtained and programmed for each vessel/radio.The built-in 15W amplifier increases the audio output of an external hailer speaker. The one-way RX hailer function enables you to broadcast radio traffic through the hailer speaker to listen to radio traffic on the deck or tower. You can also sound foghorn patterns from the hailer speaker.The Active Noise Cancelling function digitally removes background noise from transmitting and receiving audio to provide clear communications in noisy maritime environments.Specifications General Usable channels USA, INT, CAN, WX channels Power supply requirement 13.8 V DC nominal (11.7 ~ 15.9 V DC) (Negative ground) Current drain (at 13.8 V DC) TX Max. power - 5.5 A Max.RX Max. audio - 1.5 A (One CommandMicTM) 4.5 A (Three CommandMicTM and RX hailer) Operating temperature range -20 degC ~ 60 degC, -4 degF ~ 140 degF Antenna impedance 50 ohm nominal Weight (approx.) RF unit - 890 g; 2 lbCommandMicTM - 400 g; 14.1 oz Transmitter Output power (at 13.8V DC) 25 W, 1 W (High, Low) Max. frequency deviation ±5 kHz Frequency tolerance ±0.5 kHz Spurious emissions Less than -70 dBc (High power), Less than -56 dBc (Low power) Residual modulation More than 40 dB Adjacent channel power More than 70 dB Receiver Sensitivity FM (at 12dB SINAD) 0.22 μV typical Sensitivity DSC (at 1% BER) -7 dBμemf typical Adjacent channel selectivity FM More than 70 dB Adjacent channel selectivity DSC (1% BER) More than 73 dBμ emf Spurious response FM More than 70 dB Spurious response DSC (1% BER) More than 73 dBμ emf Intermodulation FM More than 75 dB Intermodulation DSC (1% BER) More than 68 dBμ emf Hum and noise More than 40 dB What's in the Box: IC-M510BB DC power cable (2 m) Microphone Hanger Connection cable, OPC-1540 (6.1 m, 20 ft) CommandMicTM, HM-195GW Connector cap Mounting base

Read more less

PYI 5 Thermal Camera Mount VerticalModel: PM5-FMD-8A 5 in tall vertical mount for thermal cameras. Powder coated brilliant white gives it a nice clean look and yet is very durable. Specifically designed for installations where space is very limited. The base for this mount is 8 in in diameter.For FLIR MD and Raymarine T200 seriesSpecifications Plate Size 8 in Height 5.63 in "

Read more less

Cannon Rail Mount AdapterModel: 1907050 Additional accessory for the Cannon Three-position Adjustable Rod Holder designed to provide the flexibility to fit any fishing scenario. Adapter for mounting three-position adjustable rod holders to boats with rails. 1-Year Limited Warranty Adapter for mounting the Cannon Three-Position Adjustable Rod Holder to any boat with rails.

Read more less

242 Rail Mount Adapter - 7/8"-1" - BlackFits 7/8" and 1" diameter round rail, and 1" square rail. For all Scotty post mount rod holders. Works with No. 241 side/deck mounts (not included). Includes: Stainless Steel FastenersWARNING: This product can expose you to chemicals including NICKEL (METALLIC) which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov.

Read more less

TripleShot™ HD T/M Bracket for Eagle Eye™Transom mount bracket for Eagle TripleShot HD Transducer.

Read more less

Furuno SC33 Compact Dome Satellite Compass, NMEA2000 (0.4 degree Heading Accuracy) w/6M CableModel: SC33The SC33 Satellite Compass provides highly accurate attitude information for navigation equipment such as Radar, Plotter, Autopilot, Fish Finder and Sonar. With its compact GNSS antenna and built-in processor, it can be used for a wide variety of applications on any type of vessel. This all-in-one system delivers incredibly accurate heading and roll & pitch information as well as heaving information, GPS position, SOG (Speed Over Ground), COG (Course Over Ground) and ROT (Rate Of Turn) data.Employing a two-antenna system with a 3-axis gyro and acceleration sensors, the SC33 enables high-speed response capability. Advanced digital signal processing techniques compute accurate heading based on sensor data. NMEA2000 interface is standard for simple installation, while the optional interface unit IF-NMEASC is available for conventional NMEA0183, AD10 and contact closure.A new GNSS antenna and advanced parallel signal processing allows the SC33 to achieve more precise Pitch, Roll and Heading measurement than conventional models, providing enhanced performance for all of your connected equipment. Its Micro-C pigtail NMEA2000 cable provides flexibility to run cables in challenging areas.In order to calculate roll & pitch data, a satellite compass requires two vectors. The SC33 employs a dual GNSS antenna system that calculates a single vector while a 3-axis rate gyro and acceleration sensors add the 2nd vector. This configuration enables the SC33 to calculate highly accurate roll and pitch data without using a third sensor.Specifications Antenna Type Radome Display Size Supplied Separately Power Usage 12-24 VDC Data Type NMEA2000 Display Type Supplied Separately Receiver Type GPS What's in the Box: SC33 6m NMEA Drop cable Hardware Adhesive Documentation

Read more less

Universal Masthead MountExtend your WindTrak 10.Sport or WindTrak 15 vane away from masthead obstructions and turbulence. The 13" (33 cm) arm comes with hardware allowing side or top mounting and offset angles up to ±20 degrees. May be attached securely to flat, curved, vertical, horizontal, or inclined surfaces. Gain space aloft and improve mounting position of wind finders and other equipment. Mount on the back of the mast for easier viewing from the cockpit. The mount adapts to virtually every masthead situation.Features: Length 13" (33 cm) Weight 3.2 oz (90 g) Boom can be shortened if necessary; complete instructions included Can be used with WindTrak Light #3200. Also accommodates Davis J-Base Mounts (using #10 stainless steel screws and nuts, not included) Specifications: Instrument Function: Wind Box Dimensions: 1"H x 3"W x 13"L WT: 0.3 lbs UPC: 011698170500

Read more less

Horizontal Round Rail Mount with Knob - 1-1/2"Magma's horizontal round rail mount with the knob replacement part.Specifications: Mount: 1-1/2" Weight: 0.93lbs/0.43kg Exterior Construction Materials: 18-8 Stainless Steel and 356 Anodized Aluminum Warranty: 1 Year

Read more less

ROKK Mini Adjustable BodyROKK Mini is a compact and multi adjustable mounting system for smart phones, tablets, small fish finders, digital and action cameras. Small in size but big on features, ROKK Mini is simply the toughest, most reliable mount for your tech onboard. No compromise.Features: Offers a large selection of base mounts to mount your devices how you want, where you want Designed, not just made; with features that you'll feel and hear more than you'll see Quick install/release with one reassuring click your tech is both secured and released A metal-on-metal locking system multiples your clamping efforts to achieve 100% locking force.  *Sold as an Individual Specifications: Cut/Uncut: Cut Mounting Style: Universal Box Dimensions: 3"H x 3"W x 6"L WT: 0.5 lbs UPC: 5060114795532 Quick Guide (pdf)

Read more less

The new Raynet (Female) to SeaTalkhs (Male) cable allows to directly connect your G-Series, E-Wide, C-Wide and E-Classic MFDs to new generation RayNet radar, sonar or other accessory that utilises the new RayNet connection. The adapter cable is 10 feet (3m) long.

Read more less

Bracket & Knobs for HDS-7 LIVEBracket and knobs specifically for Lowrance's HDS-7 LIVE. Specifications: Type: Mounting Brackets Box Dimensions: 3"H x 5"W x 14"L WT: 0.65 lbs UPC: 9420024174784

Read more less

RV-100 RealVision 3D Transom Bracket KitThis transom mount transducer service kit includes all of the spare parts and accessories originally included with the RV-100 transducer. The bracket kit includes the stainless steel transom bracket and mounting screws, kick-up pivot hardware, transducer carrier bracket and the carrier mounting bolt. *The RV-100 transducer and cable is not included. Specifications: Type: Misc Box Dimensions: 2"H x 9"W x 12"L WT: 1.1 lbs UPC: 723193817285

Read more less

Humminbird GM-H7 Gimbal MountModel: 740146-1Gimbal mount for Helix 7What's in the Box: Gimbal bracket Pair of Knobs

Read more less

ROKK Mini Tablet Mount Kit with Suction Cup BaseThe hi-performance system allows users to suction a tablet to any rigid, clean, smooth, non-textured surface. The 360-degree aluminum body features a metal-on-metal locking system that multiplies the clamping efforts to achieve 100% locking force. The tablet will never move unless the user wants it to.Features:Engineered better for longer-lasting gripTablet Clamp Top Plate Secure mount for mini and full-size tablets – ratchet adjustable Fits devices from 125mm to 220mm (5-8¼”) 360 Degree Body  Install devices instantly onboard. With one reassuring click, tech is both secured and released A metal-on-metal locking system multiplies clamping efforts to achieve 100% locking force. Electronics will never move until you want them to Suction Cup Base  Fits to any rigid, clean, smooth, non-textured surface* Tough, marine-grade, UV-stable materials Mounts quickly with over-center locking arm (no tools required) Safety lock prevents accidental release when the ROKK Mini adjustable body is attached Quick Guide (pdf)

Read more less