8261 Waterproof Panel 8 Position - Slate GreyFeatures: Will withstand the water exposures normally encountered in above deck applications: salt spray, rain, hose washdowns, momentary immersions Designed for flybridge and open cockpit applications ON-OFF Contura Switches ON indicating LEDs embedded in switches Watertight mounting gasket included Countersunk mounting holes throughout Two-part polyurethane slate gray finish Industry standard height and width Mil-Spec chemical treatment via immersion to protect every surface detail from corrosion Completely wired and ready to install Specifications: Weatherproof: Water Resistant Positions: 8 Nominal Voltage: 12v / 24v Panel Cumulative Rating: 90A Switch Rating: 20A @ 12v DC / 15A @ 24v DC Height: 3.75" Width: 9.37" Depth: 3" Included: (8) 5021 Panel Mount AGC/MDL Fuse Holder (1) 8214 Black 60 Label Set (8) 8230 Contura Switch SPST Gray - Off-On WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Waterproof: Resistant AC/DC: DC Max Breaker Quantity: 8 Voltage: 12/24v Box Dimensions: 7"H x 10"W x 10"L WT: 5.6 lbs UPC: 632085082611 Owner's Manual (pdf)

Read more less

Data Port Case/Inlet Only - 316 SS Cover with One Blank Plug & One Open PortSmartPlug data ports are the perfect complement to SmartPlug's stainless shore power inlets. It offers the same look and quality as marine-grade stainless steel components. This particular data port case has one blank plug and one open port.*All single data port inlets are supplied with one connector and one blank insert.Features: Blank and open port Weatherproof Seal, which seals against a closed-cell foam gasket in the inlet lid Locks into the edge of the SmartPlug mounting flange Only requires 4 screws to mount Silicone gasket included/no messy caulk Specifications: Material: Stainless steel Color: Stainless Steel Quick Guide (pdf)

Read more less

PC-25 Power Conditioner Noise FilterThe interference or electronic “noise” generated by alternators, ignition systems, motors, etc. can render a vehicle or vessel’s radio or other electronic equipment virtually useless. This interference takes the form of popping or static on radios or audio gear and garbled images or “hashes” on video displays.These specialized filters can be used singly or in combination to attenuate conducted line noise, either at the affected equipment or at the noise source.Features: Heavy-duty aluminum construction Operate on 6-48 VDC systems Integral mounting flanges for secure installation Nickle-plated, brass stud connectors on alternator filters accommodate high-current cables and terminals Color-coded wire leads on PC models make in-line installation easy Specifications: Filtered Frequencies: Audio – 200 MHz Rating: 25 amp Installation Location: At affected equipment in “+” and “-” leads     Dimensions (inches): 2 x 4.25 x 3.25 Weight (lbs): 2

Read more less

M2 OLED Tank MonitorThe M2 Organic LED Digital Monitor measures essential electrical system parameters with adjustable alarms and an auto-dimming display. The M2 Monitors include a MOSFET External Circuit Relay (ECR) which can be used to control external circuits based on any value measured by the M2.Features: Auto-dimming, bright Organic LED display is easy to read 80dB alarm on all models Isolated 500mA MOSFET relay Includes external DC Shunt or AC Current Transformer when required Intuitive tank level monitoring Monitor up to 4 tanks Auto calibration for unique tank shapes Compatible with common sending units Specifications: Meter: Tank Function: Monitors tank volume in up to 4 tanks Resolution: 1% Display Size: 55mm x 28mm Input Voltage: 7-70V DC - Variable with voltage, display intensity, and sleep mode Range: 0.3W-1.0W Tank Alarms: 80dB Tank Shapes: Custom shapes, auto calibration Weight: 0.25lb (0.11 kg) WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less

DC 8 Position CLB SquareFeatures: High-density circuit protection Includes 4205-Square Format Label Set Specifications: Positions: 8 Nominal Voltage: 12V DC / 24V DC Maximum Amperage*: 90A Height: 4.75" (120.65mm) Width: 4.88" (123.95mm) Depth: 3.50" (88.9mm) Weight: 1.25lb (0.57kg) * Maximum amperage ratings are dependent on use of appropriately sized fuses and wire for a given application.Includes:(8) - 7056 - Push Button Reset Only Quick Connect Circuit Breaker - 15 Amps(1) - 4205 - Basic DC Label Kit - 30 Black Square Labels [LABEL]WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: AC/DC: DC Box Dimensions: 5"H x 9"W x 9"L WT: 1.25 lbs UPC: 632085014506 Quick Guide (pdf)Owner's Manual (pdf)

Read more less

Bus Bar - 6 Way/100A with 2 Input Studs (with Red and Black)BEP bus bars include tin-plated, brass-insulated mounting bases and flame-resistant flexible plastic covers. The covers are color-coded for polarity and feature a unique push-on fit. Bus Type: Single Output screws: 6 Input studs: 2 Rating (A): 100 WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Owner's Manual (pdf)

Read more less

Yellow 3/0 AWG Battery Cable - 50' Pacer's 3/0 AWG Marine Battery Cable meets and exceeds the most stringent specifications. This UL-approved marine cable is manufactured in the USA to ensure high quality.  Marine installations can occur in tight, enclosed spaces that have sharp turns where the installation process can quickly become difficult. Pacer makes the installation process easier.  How?  By creating a flexible yet tough marine cable.  This 3/0 AWG marine battery cable can handle the toughest environments.  This marine battery cable is made from Type III tinned copper.  The copper resists corrosion and helps to extend the life of the marine cable. Then, the cable is insulated with a durable and flexible PVC jacket.  These things all come together to make the highest quality marine cable available.Features: Easy to strip, bend, and route Excellent flexibility with the durable properties of PVC Technical Specifications: Conductor - Annealed fine stranded tinned copper ASTM B172 Class K Insulation  -20 °C to 105 °C Flexible, Color Coded PVC Temperature Rating - 105 °C Dry, 75 °C Wet, 60 °C Oil Voltage Rating - 600V Resistant to - Acid, Alkali, Abrasion, Flame, Gasoline, Oil, and Moisture *Sold as an Individual Specifications: Color: Yellow Gauge: 3/0 AWG Length (Feet): 50' Box Dimensions: 8"H x 11"W x 11"L WT: 32 lbs UPC: 840248204446 Brochure (pdf)

Read more less

Edge 15W Wireless Adjustable Phone Charge Mount - 12/24VDock. Charge. Connect.Edge 15W securely holds and wirelessly charges your phone even in the toughest outdoor conditions. Now you can keep your phone in sight, fully charged, and ready to go.The IPX6 waterproof 12/24V Qi-certified waterproof wireless charging range enables wireless charging for the outdoor environment, without the need for phone charging cables. Designed from the ground up, this is the world’s first waterproof wireless charge system created specifically for use onboard, with the unique technology housed in an IPX6, fully encapsulated and sealed unit.Right up to the Edge: with the smallest footprint, Edge now means you have even more choice of how and where you install your phone mount and charger combo. Crowded consoles, side-mounting, and flat and vertical surfaces are all suitable.Put your phone on its Edge: Rotate your phone from portrait to landscape to view your favorite navigation app or simply fine-tune the position for the optimum viewing angle.12/24V and IPX6 waterproof, Edge is perfect for boat consoles tight on space or any vehicle working outside in the elements, with simple one-handed operation you can easily dock and instantly start charging your phone. No cable is required.The self-aligning, high-grip jaws accommodate all wireless charging phones and securely hold your device in the optimum charging position every time. Couple this with the innovative adjustable body of Edge and you’ll have your phone fully charged, right where you need it.Install Edge 15W on any surface: a secure 3-point fixing system and a footprint of just 50mm (1.96”) diameter maximize your choice of location and a watertight cable pass-through completes the installation.Our improvements don’t just stop there, now featuring easier phone alignment with a larger charging area, and electrical componentry that has been enhanced to significantly improve your phone's charge times, even in the harshest outdoor environments.With the same great look, Edge is tried and tested in all corners of the globe in all weathers, and conditions.Featuring Qi-certified wireless technology and a “Smart” LED that indicates when your phone is charging. Throw in foreign object detection and thermal cut-off and you’re guaranteed safe, reliable charging in all environments. Charging is also possible through non-metallic, waterproof cases. Testing & CertificationEdge has been subjected to our harshest environmental, thermal, vibration, impact, and on-water testing programs. This is combined with our world-renowned expertise in waterproofing technologies, UV stabilization techniques, and premium-grade materials to ensure Edge is the best and only choice to make when it comes to mounting and wirelessly charging your phone outdoors.International certifications include: Qi, CE, FCC, and UN-ECE R10.Features: 15W Fast Charging IPX6 Waterproof Qi Certified Mount & charge High friction grip Rotate your phone through 90 degrees Switch up your phone viewing angle on the move Specifications: Input Voltage Range: 10-30V DC (12/24V system) Input current max: 2A Output Power: 5W/7.5W/10W/15W (dependant on phone model) Standby Power: Input Voltage (V) 12/24, Standby Power (W) <0.9W, <1.1W Cable AWG: 20 AWG Cable Length: 500mm (19.69") Certification: Qi, CE, FCC, ROHS, E24, C-Tick, PSE Certified

Read more less

Power-Pac 7AH Power SupplyThe 12V DC power supply features built-in backup batteries, which are charged during normal operation and then continue to power radios and critical navigation equipment when AC power is lost. The Power-Pac is ideal for commercial vessels, work boats, and yachts.The Power-Pac’s highly regulated, low-rising 10-amp output powers radios and other sensitive communications equipment without causing RF or audio interference. At the same time, it floats and charges one or two (depending on the model) built-in 7-amp/hour backup batteries. These are kept at peak charge during the normal functioning of the unit when AC is being supplied. In the event of a loss of AC power, the internal batteries automatically take over to power communication equipment, providing a true uninterruptible DC source.Features: Highly regulated, low ripple, noise-free 12-volt output Built-in, “on-line” stand-by battery provides immediate backup power in case of AC power loss Internal mounting space and terminals for conversion of the 7 A/H model into the 14 A/H model Output “Normal” indicator L.E.D. “Back-up power only” warning light Audible and visual low battery (10.7 VDC) voltage indicators Low battery warning buzzer mute switch Automatic low battery (10.3 VDC) voltage disconnect Low voltage disconnect override button Over-voltage protection Current limit protection Input/output fused Separate output terminals are provided for charging external batteries 115/230 50-60 Hz input, selected by a slide switch on the rear panel Specifications: Battery Capacity: 7 amp/hour   Case Size (H x W x D): 5.3 x 9.0 x 10.5 inches (13.3 x 22.9 x 26.7 centimeters)   Weight: 18 lbs. (8.2 kg) Input: 115/230 VAC, 50-60 Hz. Output: 13.6 VDC @ 5A cont., 10A Int. Regulation: 1% line and load Ripple: 1% P-P Operating Temp: 0-40 degrees C With a 7 Amp/Hour Battery Installed, the Unit Provides Approximately the Following Power. *7 Amps for 40 Min. 10 amps for 20 min. 15 amps for 10 min. 20 amps for 4 min. *Assuming battery at full charge when a.c. power failed.The Power-Pac 7 A/H (single battery model) can power a 25-watt transceiver for up to 3 hours, based on a 20% transmit/receive duty cycle. Power-Pac 14 A/H can provide the same service for up to 6 hours. Provision is made for expanding backup power up to twelve hours (in this example, longer under lesser loads) with the installation of additional externally wired batteries (total 28 amps/hours max.). Batteries are automatically recharged when the AC is restored.The operator is kept informed of all important functions, such as AC input, DC output, and battery status, with front panel indicator lights and a low battery warning buzzer.Protection: AC Input fuse Internal and external Battery fuses Over Voltage Current Limit Automatic Thermal Shutdown Low Battery Disconnect Mechanical Details: Vinyl Laminated aluminum case 6’ standard AC power cord Ac input selector switch Battery Details: Sealed Lead Acid, Deep-cycle. Certified by DOT and IATA for shipment by Air Weight per 7 AH Battery; 6 lbs. Size (inch): 6” x 3.75” x 2.5” Options: Form C AC Failure Contacts (Contact factory for details) Extra batteries, sold separately 7 A/H increments; each Power Pac will accommodate 28 A/H max. (14 internal, 14 external) This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns. Quick Guide (pdf)Owner's Manual (pdf)

Read more less

Mac Plus 12/24-30 + CZoneBoost the Service BatteryToo often, service batteries don’t get the charge they need. This is a problem made worse by smart alternators and start/stop systems, which result in slow and insufficient charges. The Mac Plus DC-DC charger solves this problem, providing a quick, safe, and consistent charge to the service battery. And, by knowing when the engine is running and providing charge, users can be sure that the Mac Plus will never drain a starter battery.Proven Mastervolt QualityUsers get peace of mind knowing that they have the best on board. Using the proven Mastervolt 3-step+ charge algorithm, the Mac Plus delivers a quick and easy charge, even for completely flat batteries.A robust design holds up in even the harshest conditions, with battery temperature-optimized charging and a high-quality aluminum housing to ensure superior protection against dust and water ingress. The power-efficient design also allows the Mac Plus to operate silently and without a fan.Total Power FlexibilityWith a wide DC input range, the Mac Plus allows for all DC sources and can charge two batteries from a single alternator or charger. It supports a full range of chemistries and battery types, including lithium. It also functions seamlessly with modern alternators such as Euro 5 and 6, ensuring proper charging by providing constant power, even when the alternator is inactive.Parallel configuration of up to ten units will provide over 100 amperes. Advanced high-frequency technology with modern microprocessors ensures minimal power loss when switching from 12V to 24V and vice versa.Analog voltage sense ports are also available to compensate for voltage drops and maintain proper charging.Superior Monitoring & ControlCompatibility with CZone®, NMEA 2000®, and MasterBus delivers truly superior monitoring and control and ensures Mac Plus integrates easily into complete systems. Achieve the best performance possible via various controllers and high-quality MOSFETs. And configure the Mac Plus with ease via MasterAdjust, the CZone configuration tool, or even via the on-board DIP switches.Features: Fast and safe charging, even during short trips Fanless design for silent operation Suitable for flooded, Gel, AGM, and Li-Ion batteries (incl. LiFePO4) Even charges fully depleted batteries Engine run detection protects the starter battery Adjustable current limits to meet Euro 5/6 requirements Voltage stabilization protects sensitive equipment, lights, and loads Parallel operation to obtain charging capacities well over 100 Amps MasterBus, CZone, and NMEA 2000 are compatible for intelligent system monitoring and automation Temperature compensation and voltage sense for an optimal charging result E-Mark/R10 certification for mobile applications Power supply mode offers stable power for sensitive loads Heavy-duty connections for easy installation and quick setup via DIP switches Specifications: Battery Temperature Sensor: Yes, included Battery Voltage Sense: Yes  General Specifications: Status Indicator: Yes, 3-color LED Communication Protocol: MasterBus, CZone & NMEA 2000 Output Voltage: 20-30 V Nominal Output Voltage: 24 V Output Voltage Stabilization: 2 % at extremes of temperatures, load, and input Output Voltage Ripple (peak-peak): Max. 1 % Max. Output Power: 725 W Nominal Output Power: 675 W Max. Output Current: 30 A Output Charge Current (3-step mode): 30 A Nominal Input Voltage: 12 V Input Voltage Range: 10-16 V Max. Input Current: 50 A Galvanic Isolation: No Voltage Limited: Yes Efficiency: > 95 % (at nom. input voltage, full load); peak 97 Parallel Configuration: Yes Alarm Contact: Yes, through MasterBus MasterBus Powering: No Engine Run Signal Input: Yes (active high/active low) DIP Switches: Yes, for basic setup Dimensions, H x W x D: 255 x 165 x 66 mm (10.0 x 6.5 x 2.6 inch) Weight: 2 kg (4.4 lb) Compliance: CE, E-Mark, SAE J1171 & ISO 8846 Ignition Protected  Technical Specifications: No-load Consumption: < 2 mA Charge Characteristic: 3-traps+ Battery Types: Flooded, Gel, AGM, spiral, Lithium Ion, traction, user-defined 3-Step Charge Option: Yes (DIP switch settings) DC Consumption: < 5 mA Connections: 3 x M8 terminal for cable diameters of 10-50 mm², (positive input, positive output, joint negative connection) 8-pole screw connection for cable diameters of 0.75-1.5 mm² (remote on/off, temperature sensor, voltage measurement Temperature Range (ambient temp.): -25 degrees C to 60 degrees C; derating > 40 Cooling: Natural cooling Protections: Overload, over temperature, DC short circuit, reversed polarity (fuse) MasterBus Compatible: Yes Specifications: Charger Input - Voltage: 12v Charger Output - Amps: 30a Charger Output Voltage: 20-30v Box Dimensions: 4"H x 9"W x 15"L WT: 5.55 lbs UPC: 816882023507 Owner's Manual (pdf)

Read more less

ROKK Wireless Nano 10W Waterproof 12/24V ChargerDock. Charge. Connect.Nano 10W is our smallest wireless phone charging mount. It squeezes big features into a tiny package! Designed to be installed where space is at a premium, Nano 10W holds and wirelessly charges your phone at the same time! The ultra-compact design can be installed and used in any orientation, unlocking new charging possibilities. Now you can keep your phone within reach, charged, and ready to go.The IPX6 waterproof, 12/24V wireless range enables phone charging for the outdoor environment, without the need for cables. Designed from the ground up, this is the world’s first waterproof wireless charge system created specifically for use onboard.Perfect for boat consoles or any vehicle working outside in the elements, Nano 10W has been designed to fit even the largest phones. Nano 10W features Qi-certified wireless charging technology with foreign object detection and thermal cut-off to guarantee your devices are kept safe and charged while onboard.The upgraded 10W chargers are up to 60% faster and have been designed for the latest generation of power-hungry devices and apps. Nano 10W is compatible with all wireless charging-enabled phones of all sizes from all major brands. Charging is also possible through non-metallic, waterproof cases. UsageNano 10W is at home in coastal and freshwater. If you require a wireless phone charging mount for rough conditions, we recommend our ROKK Wireless – Active 10W or Edge 10W.  TestingROKK Wireless Nano has been subjected to a high level of environmental, vibration, impact and on-water testing programs. This is combined with our world-renowned expertise in waterproofing technologies, UV stabilization techniques and premium-grade materials, ensuring Nano 10W is up to the challenge of life outdoors.InstallationInstallation is simple on any boat, RV, ATV or outdoor location. Four screws secure the unit onto any flat surface with a simple installation guide and drilling template. For the best phone grip performance, a vertical installation is recommended. The charger is easy to clean and can be washed down with fresh water.Features: 10W Fast Charging IPX6 Waterproof Qi Certified Mount & charge Outdoor-ready grip Brochure (pdf)

Read more less

Black 2 AWG Battery Cable - 100' Pacer's 2 AWG Marine Battery Cable meets and exceeds the most stringent specifications. This UL-approved marine cable is manufactured in the USA to ensure high quality.  Oftentimes, marine applications are in enclosed areas with sharp turns. Installation can become difficult. Pacer simplified this process by developing flexible yet tough marine cables. This 2 AWG marine battery cable is built to handle the harshest conditions. All our marine cable is made from Type III tinned copper. The copper resists corrosion and ensures the longevity of the cable.  It is then insulated with a durable and pliable PVC jacket. These things together make it the highest quality marine battery cable available. Features: Easy to strip, bend, and route Excellent flexibility with the durable properties of PVC Technical Specifications: Conductor - Annealed fine stranded tinned copper ASTM B172 Class K Insulation  -20 °C to 105 °C Flexible, Color Coded PVC Temperature Rating - 105 °C Dry, 75 °C Wet, 60 °C Oil Voltage Rating - 600V Resistant to - Acid, Alkali, Abrasion, Flame, Gasoline, Oil, and Moisture *Sold as an Individual Specifications: Color: Black Gauge: 2 AWG Length (Feet): 100' Box Dimensions: 7"H x 10"W x 10"L WT: 27 lbs UPC: 840248203944 Brochure (pdf)

Read more less

1842 M2 OLED Digital Bilge MeterThe M2 Organic LED Digital Monitor measures essential electrical system parameters with adjustable alarms and an auto-dimming display. The M2 Monitors include a MOSFET External Circuit Relay (ECR) which can be used to control external circuits based on any value measured by the M2.Features: Auto-dimming, bright Organic LED display is easy to read 80dB alarm on all models Isolated 500mA MOSFET relay Bilge float switch not included Specifications: Meter: Bilge Function: Monitors up to 4 bilges Alarm/Relay Activation: Run time/hr Cycles/24 hr Average Cycles Display Size: 55mm x 28mm Input Voltage: 7-70V DC Range: 0.3W-1.0W WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Owner's Manual (pdf)

Read more less

ATC Six Way Bus Bar with 5mm Input StudThe ATC Negative Bus uses the BEP Contour lock system to allow it to be joined to the ATC fuse holder. This keeps wiring tidy and conveniently located. Current Rating: 100Amps.WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less

3000W Pure Sine Wave Inverter - 12VPST Series (120 VAC)This high efficiency pure sine inverter converts 12 Volts DC to 3000 Watts of AC power at 120 Volts, 60 Hz. Features include temperature controlled cooling, low interference, wide temperature operating range, overload protection, low battery alarm / shut down & low idle power draw. AC power is available from dual NEMA-20R GFCI outlets on the front panel, the unit is also hard wire capable. Safety certified to UL and CSA standards, FCC Compliant.Optional LCD remote control, model RC-300.Features: High efficiency & low RF emissions Can be hard wired 2x Surge Wide DC input range Dual GFCI Protected Outlets Wide temperature operating range -20 to +40°C / -4 to +104°F Temperature controlled cooling fan Low idle power draw Remote Input – Use to turn inverter ON or OFF with ignition start or any other Remote ON/OFF switch Optional LCD remote control, model RC-300 UPC – Universal Protection Circuit: low voltage, over voltage, over temperature, over load and short circuit Safety certified to UL & CSA standards, FCC compliant Specifications: Input: 12 VDC Output: 120 VAC Watts: 3000 Watts Remote Control: RC-300 Optional Weight: 21.6 (lbs) Weight: 9.8 (kg) Dimensions: 10.35 x 17.97 x 5.71 Dimensions: 263 x 456.5 x 145 (mm) Safety: UL, CSA Warranty: 2 Year Limited Applications: Service vehicles Mobile Offices Boats Recreation Vehicles, Camping Telecommunication Field work / Construction sites Solar power systems Emergency backup power Home electronics: TV, VCR, video games Computers, printers WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Inverter Cont. Output Wattage: 3000w Outlet Qty: 2 Duplex GFCI Inverter Input Voltage: 12v Waveform: Pure Sine Wave Box Dimensions: 9"H x 14"W x 21"L WT: 24.8 lbs UPC: 622988072420 Owner's Manual (pdf)Brochure (pdf)

Read more less

Horizontal Battery Distribution Cluster f/Single Engine w/Two Battery BanksThe 716-H-140A-DVSR is an ideal replacement for a battery selector switch. Just remove the selector switch and connect the existing wires to a 716 cluster, no extra wires are required for a fully automatic battery management system. To be used in a single outboard dual battery bank system or in a single alternator inboard engine dual battery bank system. No more flat start batteries Electronics protection from harmful engine start spikes The 716 cluster is for use on charging systems up to 150A The 716 cluster replaces battery isolator systems Two battery banks WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Owner's Manual (pdf)

Read more less

DS40-P Vertical Cable SealScanstrut premium IP68 waterproof cable seal provides easy fit cable routing that cuts down your installation time and is the only guaranteed and proven watertight installation for your antenna and navlight cables. Features: Watertight installation - 100% waterproof with an IP68 rating Easy and reliable installation - each unit supplied with both pre-drilled and blank inner seals to make your installation as easy as possible.  No Need to Remove Cable Connectors - split-seal option does not require connector removal during install.  Multi-Functional Dome Shape - the aesthetic dome-shaped profile provides a stronger, impact-resistant design and outer dome provides additional water shield. Technical Specifications: Fits cable size (diameter) - .4" to .59" (12 - 15 mm)   Fits connector size up to 1.57" (40 mm) in diameter  Height - .85" (20.5 mm) Color - Grey Orientation - Vertical Material - ASA Plastic In the Box: Cable seal Mounting hardware Installation manual  *Sold as an Individual Specifications: Type: Deck Seal Box Dimensions: 1"H x 4"W x 6"L WT: 0.4 lbs UPC: 5060114792821 Quick Guide (pdf)Brochure (pdf)

Read more less

11003Features: Meets American Boat and Yacht Council (ABYC) requirements for battery switches Ignition protected safe for installation aboard gasoline powered boats Case design allows surface or rear panel mounting Accepts two 4/0 AWG (95mm) battery cables M12 tin-plated copper studs for maximum conductivity and corrosion resistance, accepts 1/2" and M12 ring terminals 7/8" (22.22mm) stud length to accept multiple cable terminals Tactile textures indicate knob position by feel only Case design allows surface or rear panel mounting Switch Ratings: 10 Sec: 2750A60 Sec: 1150A5 Min: 700AContinuous: 500AMax Voltage: 32V DCWARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: AFD: Yes Positions: 3 Box Dimensions: 3"H x 7"W x 9"L WT: 1.3 lbs UPC: 632085110031 Brochure (pdf)

Read more less

Battery Isolator - 1 Alternator - 2 Battery - 70 AMPProMariner Battery Isolators with gold-plated terminals and improved efficiency, provide enhanced charging. Rated for use with DC devices ranging from 10 amps to 70 amps. Owner's Manual (pdf)

Read more less

ProTournament Elite Wired RemoteRemotely monitor the charge status of the ProTournament Elite Battery Charger.Features: Intuitive tri-color design allows for quick identification of battery charger stage Compatible with all models of ProTournament Elite Battery Chargers 12' length

Read more less

2-Position SPST Push-Pull Switch w/Contoured Knob - OFF/ONSingle pole, single throw switch turns one circuit on and off. Heavy-duty, noncorrosive construction with moisture-repellent insulators. Brass case, stem, terminals and mounting hardware. All knobs are screw-on type.Features: Nominal voltage is 6-36V DC Rated for 10A at 12V DC #8-32 screw terminals Fits panels up to 3/4" thick Same as Cole Hersee part number M-628 WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Color: Chrome Action: ON-OFF Throw/Pole: SPST Box Dimensions: 2"H x 3"W x 5"L WT: 0.2 lbs UPC: 870216046013

Read more less

Mini Battery Selector SwitchThe 701S is the most compact selector switch available on the market. While BEP recommends isolated battery systems as outlined with our distribution clusters, the 701S provides a simple economical way of separating two batteries. BEP Marine Battery Switch Test Procedures (UL 1107) Continuous (1 hour), intermittent (5 minutes) and Cranking (engine starting - 10 seconds). The test is to determine the maximum current the switch can handle for the stated time, without the rear terminals exceeding 100 deg C (212 deg F) above the ambient temperature. The continuous and intermittent ratings are tested at 110% of specified ratings. All BEP switches are tested Independently to this specification by a 3rd party laboratory. Housed in the same dimensions as the 701, and includes the same removable side plates and back cover Please note selector switches will not separate electronics from harmful engine starting spikes Tin-plated copper studs and nuts Ignition-protected WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Quick Guide (pdf)Owner's Manual (pdf)

Read more less

200A Z Bar 18 Way Bus BarThis patent-pending, space saving buss bar range is a completely new concept for marine cable termination. Offering almost unlimited installation flexibility, the high and low level bars can be bussed together with Z-Link or used as separate positive/negative bars. Easily extend Z-Bars by placing on end or back-to-back Clean installation-all cables can be run from one side of the Z-bar Innovative clear covers insulate and protect on three sides and offer easy access WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Brochure (pdf)

Read more less

On-Board Battery Charger 10A / 12V - 2 Bank - 120V InputGuest On-Board battery chargers have been redesigned from the inside out with the customer in mind. Our newest generation On-Board Marine battery chargers include leading advancements in digital charging technology and waterproof design/construction. Every Guest charger has a dedicated charging, sensing and control per bank. The easy to read graphics indicates the status of each battery bank through the charging process.Features: All high frequency, digital charging technology Fully automatic 5-stage performance charging Dedicated battery charging, sensing and control per bank Expanded LED charge status monitor Wiring and battery fault detection Auto-maintain energy saver mode Up to 40 percent lighter 100 percent Waterproof (IP67) and shock resistant for all fresh and saltwater applications All models are pre-wired for easy installation For all 12 volt flooded and AGM lead acid batteries Built-in safety: reverse polarity, over-current, over-voltage, over-temperature and ignition protection. In-line fuses for maximum DC wire protection. 2 year warranty WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Charger Output Voltage: 12/24v Charger Output - Amps: 10a Charging Banks: 2 Portable: No Charger Input - Voltage: 120v Box Dimensions: 6"H x 9"W x 12"L WT: 5.7 lbs UPC: 046904904112 Owner's Manual (pdf)Brochure (pdf)

Read more less

15A Battery Charger - 12V - 3-Bank - 3-Stage w/Dip Switch & LugsThis advanced fully automatic three-stage 15 Amp battery charger is ideal for charging all types of 12 Volt lead-acid batteries ( Flooded / Absorbed Glass Mat (AGM) / Gel Cell) from a 120 V, 60 Hz or 230 V, 50 Hz AC source. By means of a DIP switch setting, conversion to a two-stage algorithm is possible to charge batteries connected to a DC load (DC UPS). The unit can also be used as a DC Power Supply. Features include overload and short-circuit protection. The unit allows charging of up-to 3 separate battery banks.Features: High efficiency Commercial Grade Lightweight Quiet operation Industry Proven Design – 1000s of units in operation 2 or 3 stage charging (user selectable) 120 or 230 VAC, 50/60 Hz (user selectable) Voltage meter display – Ammeter and LED power status For all types of Lead Acid batteries Charge with a battery load or stand alone Use as a power supply or DC UPS UPC: Universal Protection Circuit – short circuit, overload, reverse battery polarity Charge 3 banks of batteries at once – no isolator necessary Specifications: Input: 120 VAC 60 Hz or 230 VAC 50 Hz Output: 12 VDC Amps: 15 Amps Weight: 4.4 (lbs) Weight: 1.96 (kg) Dimensions: 8.5 x 8.5 x 3 (in) Dimensions: 21.6 x 21.6 x 7.6 (cm) Safety: Listed to UL Standard UL-1564, EMI Compliant to FCC Part 15(B), Class B Warranty: 2 Year Limited Applications: Automotive Recreational vehicles Marine Communications sites Battery back-up systems WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Charger Output Voltage: 12v Charger Output - Amps: 15a Charging Banks: 3 Portable: No Charger Input - Voltage: 120/240v Box Dimensions: 5"H x 10"W x 12"L WT: 5.5 lbs UPC: 622988083013 Owner's Manual (pdf)Brochure (pdf)

Read more less

ConnectPro® 3-Wire PlugFeatures: O-ring seal for waterproof connections Weather resistant plug cover Corrosion resistant, plated brass electrical components Accepts 16 to 8 gauge wire Ergonomic contoured grip for easy hook-up and ground blade alignment WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Type: Plugs Box Dimensions: 2"H x 5"W x 6"L WT: 0.1 lbs UPC: 093344304644 Quick Guide (pdf)Brochure (pdf)

Read more less

PDM 14 Circuit + Ground 175A 12V with Kill SwitchDesigned for professional installers, this is a compact solution that combines battery protection, power switching, circuit protection, a ground bus, and an optional manual override switch.  This includes three 45-amp high-power circuits and three output groups, which can be independently set to 24/7, ignition switched, or time delay.  Expandable up to 31 fused outputs with RT or CT fuse blocks.Features: For 12-volt systems, the allowed voltage range is 8-18 VDC Total continuous output limit: 175 amps Three load groups with a continuous output of 75-115 amps Optional time  delay 0-10 hrs Optional low voltage protection 11-12.2 volts Offload current draw 1.3 mA Quick Guide (pdf)

Read more less

Dual XD Flex 2 - Relay - ACR with KnobsFeatures: Bullet-proof Construction: Sealed to IP67/IP6K9K, high-temperature electronics and materials allow mounting anywhere. Stainless steel cable lug studs. Large mounting holes accept 1/4-20 / M6 attachment hardware. Intuitive Manual Control option simplifies operation and awareness of the state of manual override and whether the device is being left in a locked off or locked on state (not available on competitive solutions) Simple Programmability via simple dip switches allows each relay function significant flexibility for OEMs and installers.  35-75% Reduction in Mounting Space & Product Weight via advanced bi-stable solenoid design and multiple solenoid assemblies that replace common electrical system layouts. Plug & Play Compatible with Legacy Competitor Products:   Single, dual, and triple relays options available with DTM/ATM connectors, pin for pin compatible with ML Series Bi-stable Relays. 90-95% Less Off-State Current: Compared to competitive products and system solutions that require multiple devices for similar functionality. Applications: Replaces Two Individual High Amp Relays with One Compact Module, reducing space significantly, eliminating the cost of external link cable connections, eliminating the risk of link cable connections vibrating loose, and providing clear, unambiguous awareness of how to operate manual controls and what state the manual controls have forced the relay into.. Designed to Replicate Common Multi-Battery Switching and Charge Management Functions:  Common dual battery load switching via the outer relays and a central automatic charging relay to share charge current is easily implemented. Multiple Automatic Charging Relay (ACR) Into One Device: For 2-3 Battery Systems that require 1 or 2 ACRs, a single three-relay ACR provides drastic improvement in off-state quiescent current draw, space used, and reduces unnecessary interconnection cables.. Expandable with Link and Cross-Link Busbars to Additional Dual, Triple, or Single XD Relays: Supports 2 or 3 battery systems with standard busbar interconnect accessories. Specifications: Type: Electric Box Dimensions: 3"H x 4"W x 8"L WT: 2 lbs UPC: 850035199626

Read more less

100A Surface Mount Circuit Breaker - 285 SeriesThis 100A Egis circuit breaker protects electrical circuits from short-circuit events and over-current loads, preventing wire insulation overheating and subsequent destruction.Applications: Automatic circuit protection and manual on/off switching combine dual functionality in one reliable and compact solution Allows for circuit isolation and maintenance of load circuits by providing convenient switching and integral circuit protection capable of mounting adjacent to battery systems regardless of the location Features: Sealed against dust and water intrusion to ensure reliable circuit protection for the life of the electrical system installation  High Voltage (48 Vdc) Rating - easily supports 12 and 24 VDC applications while offering advanced protection for 36 and 48 VDC High Electrical / Manual Switching Endurance delivers 6,000 cycles at full current High Interrupt Current - safely protects circuits connected to large paralleled battery banks with significant available power 4-Year Warranty - Egis stands behind its product's ability to meet the user's needs Specifications: Continuous Current Amps: 100 Max Voltage: 48 Cycling Endurance: 6,000 Interrupt Current @16 VDC (Amps): 5,000 Interrupt Current @28 VDC (Amps): 3,000 Ingress Protection Rating: IP67 Focal Features:ON/OFF High Visibility ControlsSealed against dust and moisture penetration. The high temperature rating for all installation locations.Integrated Terminal InsulatorsProtects against inadvertent shorts from positive terminals to adjacent grounded surfaces.Stainless Steel Hardware / Serrated Flange NutsCorrosion and vibration resistance for harsh environment applications.Proudly Made in the USAMade in the USA of high-quality components.WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Amperage: 100a Box Dimensions: 3"H x 3"W x 5"L WT: 0.2 lbs UPC: 850035199176 Quick Guide (pdf)

Read more less

Red 4 AWG Battery Cable - 100' Pacer's 4 AWG Marine Battery Cable meets and exceeds the most stringent specifications. This UL-approved marine cable is manufactured in the USA to ensure high quality.  Oftentimes, marine applications are in enclosed areas with sharp turns. Installation can become difficult. Pacer simplified this process by developing flexible yet tough marine cables. This 4 AWG marine battery cable is built to handle the harshest conditions. All our marine cable is made from Type III tinned copper. The copper resists corrosion and ensures the longevity of the cable.  It is then insulated with a durable and pliable PVC jacket. These things together make it the highest quality marine battery cable available. Features: Easy to strip, bend, and route Excellent flexibility with the durable properties of PVC Technical Specifications: Conductor - Annealed fine stranded tinned copper ASTM B172 Class K Insulation  -20 °C to 105 °C Flexible, Color Coded PVC Temperature Rating - 105 °C Dry, 75 °C Wet, 60 °C Oil Voltage Rating - 600V Resistant to - Acid, Alkali, Abrasion, Flame, Gasoline, Oil, and Moisture *Sold as an Individual Specifications: Color: Red Gauge: 4 AWG Length (Feet): 100' Box Dimensions: 7"H x 7"W x 8"L WT: 18.75 lbs UPC: 840248203845 Brochure (pdf)

Read more less

T-H FLEX™ 2" Expandable Braided Sleeving - 50' RollT-H FLEX™ is a lightweight, braided jacketing for bundling and protecting wires, cables and hoses. Braided from high temperature yarns, T-H FLEX™ offers total protection for wire and cable assemblies. The unique expansion characteristics makes T-H FLEX™ easy to slip on. Only a few sizes are needed to cover a large diameter range, since each size of T-H FLEX™ expands up to four times its normal diameter.  The sleeving cuts easily and cleanly with a hot knife and once installed, will beautify and protect any wire, hose or cable application.Features: Lightweight Protective Sleeving Protects Wire, Cables and Hoses Braided from High Temperature Yarns Chemical Resistant Simplifies and beautifies any rigging application Specifications: Type: Misc Box Dimensions: 6"H x 9"W x 10"L WT: 2 lbs UPC: 733572036855

Read more less

AC Current TransformerRatio: 50A AC/50mA ACFor use with AC AmmetersWARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less

AC Universal Plug Holder - BlackFeatures: Black AC Universal Plug Holder is designed for all standard 120V AC plugs Plug clamp insert included—converts plug holder to an AC inlet for battery chargers No cutting, stripping, or rewiring of AC power cord Watertight and UV resistant cover. Stainless steel mounting screws included Easy to reach safe AC power cord connections

Read more less

Black 6 AWG Battery Cable - Sold By The Foot ANCOR Marine Grade™ wire is manufactured from tinned copper stranding for maximum protection against corrosion and electrolysis. Ultra flexible (Type 3) stranding resists fatigue due to vibration and flexing. ANCORs proprietary premium vinyl insulation stays flexible even in extreme cold and resists salt water, battery acid, oil, gasoline and ultra-violet radiation. Exclusive insulation is rated at 600V, 105°C dry and 75°C wet, and is resistant to heat and abrasion. Exceeds all UL 1426, US Coast Guard Charter boat (CFR Title 46) and ABYC standards WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Color: Black Length (Feet): Sold By The Foot Gauge: 6 AWG Box Dimensions: 1"H x 1"W x 12"L WT: 0.1 lbs Owner's Manual (pdf)

Read more less

Remote for Freedom HF Series Inverter/ChargersReplacement panel for Freedom HF Series inverter/chargers.*Does not include connection cable.Compatible With:Freedom HF Series inverter/chargersFeatures: View key system information Configure and monitor important parameters and settings Conveniently view fault and error codes Technical Specifications: Input Voltage: 12V AC Output: GFCI and/or Hardwire In the Box: Remote panel Instruction manual *Sold as an Individual

Read more less

50' RJ12-6 Cable for Freedom Remote Panel OptionalXantrex 50' remote cable for Prowatt SW Remote Control For use with ProWatt Series 50' length, replaces 25' cable supplied with unit Includes connectors WARNING: This product can expose you to chemicals including Diisononyl Phthalate (DINP) which is known to the State of California to cause cancer, and Di-isodecyl Phthalate (DIDP) which is known to the State of California to cause reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less

PRO Series InvertersPerformance inverters designed for RVs and boatsDesigned for RV and marine electrical systems that already have a battery charger or generator installed, Xantrex PRO Inverters deliver modified sine wave power for small appliances, TVs, and other onboard electronics from a battery bank. DescriptionThe Xantrex PRO Series Inverters are the perfect complement to generators when shore power is unavailable, to quietly and efficiently provide household power when needed. The PRO Series design is both user friendly and versatile. These inverters feature a detachable, digital remote control to display precise inverter, AC source and battery status information from one convenient location. A built-in transfer switch automatically detects when generator or shore power status changes to ensure power is always available. The 1800W is designed for demanding RV and marine conditions. They meet FCC Class B regulations to eliminate interference potential with other electronics, while UL 458 certification means they meet strict RV and marine safety standards. Versatile enough to be mounted either horizontally or vertically, these inverters can be easily installed to fit into any compartment. Conformal coated boards also minimize the chance of problems from moist operating conditions. Performance Features Inverter easily powers TVs, small appliances, and other electronics Built-in 15A circuit breaker to protect GFCI connected loads Up to 25A pass through for hardwired loads Digital remote control displays power output, AC source and battery voltage Detachable remote control can be mounted wherever convenient Conformal coated electronics provide moisture resistance Designed to be hard-wired using a terminal strip or by connecting AC through a GFCI receptacle (included) Protection Features Battery over-voltage and under-voltage protection Over temperature shutdown Automatic overload protection Short-circuit protection Ground fault protection WARNING: This product can expose you to chemicals including Diisononyl Phthalate (DINP) which is known to the State of California to cause cancer, and Di-isodecyl Phthalate (DIDP) which is known to the State of California to cause reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: DC Connection Type: Hardwire GFCI: Yes Inverter Input Voltage: 12v Outlet Qty: 1 Duplex GFCI Inverter Surge Rating: 3600w Waveform: Modified Sine Wave Inverter Output Voltage: 120v AC Connection Type: Hardwire Inverter Cont. Output Wattage: 1800w Box Dimensions: 6"H x 10"W x 18"L WT: 13 lbs UPC: 715535113537 Owner's Manual (pdf)Brochure (pdf)

Read more less

Heavy-Duty Battery Tray - 29/31 Battery SeriesThis heavy-duty Attwood battery tray is for a group 29 or group 31 battery and is made of non-corrosive black plastic.Features: Includes an adjustable-height crossbar and stainless steel retaining bolts Meets ABYC Standard E-10 and U.S. Coast Guard requirements Install with #10 fasteners Specifications:Inside Dimensions (L x W): 13-1/16" L x 6-7/8" W Quick Guide (pdf)

Read more less

Yellow 4/0 AWG Battery Cable - 25' Pacer's 4/0 AWG Marine Battery Cable meets and exceeds the most stringent specifications. This UL-approved marine cable is manufactured in the USA to ensure high quality.  Marine installations can occur in tight, enclosed spaces that have sharp turns where the installation process can quickly become difficult. Pacer makes the installation process easier.  How?  By creating a flexible yet tough marine cable.  This 4/0 AWG marine battery cable can handle the toughest environments.  This marine battery cable is made from Type III tinned copper.  The copper resists corrosion and helps to extend the life of the marine cable. Then, the cable is insulated with a durable and flexible PVC jacket.  These things all come together to make the highest quality marine cable available.Features: Easy to strip, bend, and route Excellent flexibility with the durable properties of PVC Technical Specifications: Conductor - Annealed fine stranded tinned copper ASTM B172 Class K Insulation  -20 °C to 105 °C Flexible, Color Coded PVC Temperature Rating - 105 °C Dry, 75 °C Wet, 60 °C Oil Voltage Rating - 600V Resistant to - Acid, Alkali, Abrasion, Flame, Gasoline, Oil, and Moisture *Sold as an Individual Specifications: Color: Yellow Gauge: 4/0 AWG Length (Feet): 25' Box Dimensions: 6"H x 10"W x 10"L WT: 22.5 lbs UPC: 840248204545 Brochure (pdf)

Read more less

Red 2 AWG Battery Cable - Sold By The Foot Pacer's 2 AWG Marine Battery Cable meets and exceeds the most stringent specifications. This UL-approved marine cable is manufactured in the USA to ensure high quality.  Oftentimes, marine applications are in enclosed areas with sharp turns. Installation can become difficult. Pacer simplified this process by developing flexible yet tough marine cables. This 2 AWG marine battery cable is built to handle the harshest conditions. All our marine cable is made from Type III tinned copper. The copper resists corrosion and ensures the longevity of the cable.  It is then insulated with a durable and pliable PVC jacket. These things together make it the highest quality marine battery cable available. Features: Easy to strip, bend, and route Excellent flexibility with the durable properties of PVC Technical Specifications: Conductor - Annealed fine stranded tinned copper ASTM B172 Class K Insulation  -20 °C to 105 °C Flexible, Color Coded PVC Temperature Rating - 105 °C Dry, 75 °C Wet, 60 °C Oil Voltage Rating - 600V Resistant to - Acid, Alkali, Abrasion, Flame, Gasoline, Oil, and Moisture *Sold by the Foot Specifications: Color: Red Gauge: 2 AWG Length (Feet): Sold By The Foot Box Dimensions: 1"H x 1"W x 12"L WT: 0.1 lbs Brochure (pdf)

Read more less

Black 2 AWG Battery Cable - Sold By The Foot Pacer's 2 AWG Marine Battery Cable meets and exceeds the most stringent specifications. This UL-approved marine cable is manufactured in the USA to ensure high quality.  Oftentimes, marine applications are in enclosed areas with sharp turns. Installation can become difficult. Pacer simplified this process by developing flexible yet tough marine cables. This 2 AWG marine battery cable is built to handle the harshest conditions. All our marine cable is made from Type III tinned copper. The copper resists corrosion and ensures the longevity of the cable.  It is then insulated with a durable and pliable PVC jacket. These things together make it the highest quality marine battery cable available. Features: Easy to strip, bend, and route Excellent flexibility with the durable properties of PVC Technical Specifications: Conductor - Annealed fine stranded tinned copper ASTM B172 Class K Insulation  -20 °C to 105 °C Flexible, Color Coded PVC Temperature Rating - 105 °C Dry, 75 °C Wet, 60 °C Oil Voltage Rating - 600V Resistant to - Acid, Alkali, Abrasion, Flame, Gasoline, Oil, and Moisture *Sold by the Foot Specifications: Color: Black Gauge: 2 AWG Length (Feet): Sold By The Foot Box Dimensions: 1"H x 1"W x 12"L WT: 0.3 lbs Brochure (pdf)

Read more less

Black SPST Momentary Contact Switch - OFF/(ON)Single pole, single throw momentary switch turns one circuit on and off. Compact black push button switch can be used for horn, starter, and other momentary applications.Features: Nominal voltage is 12V/24V DC Rated for 5A at 12V DC, 5A at 24V DC Two 1/4" blade terminals Fits panels up to 1/4" thick Same as Cole Hersee part number 9187-02 WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Action: (ON)-OFF Color: Black Throw/Pole: SPST Box Dimensions: 1"H x 3"W x 5"L WT: 0.05 lbs UPC: 870216046037

Read more less

Green 6 AWG Battery Cable - Sold By The Foot ANCOR Marine Grade™ wire is manufactured from tinned copper stranding for maximum protection against corrosion and electrolysis. Ultra flexible (Type 3) stranding resists fatigue due to vibration and flexing. ANCORs proprietary premium vinyl insulation stays flexible even in extreme cold and resists salt water, battery acid, oil, gasoline and ultra-violet radiation. Exclusive insulation is rated at 600V, 105°C dry and 75°C wet, and is resistant to heat and abrasion. Exceeds all UL 1426, US Coast Guard Charter boat (CFR Title 46) and ABYC standards WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Color: Green Length (Feet): Sold By The Foot Gauge: 6 AWG Box Dimensions: 1"H x 1"W x 12"L WT: 0.1 lbs Quick Guide (pdf)Owner's Manual (pdf)

Read more less

Class T Fuse Holder with 2 Additional Studs 225-400A Providing high-capacity fusing, fast response and very high interrupt ratings (ANL up to 6,000 Amps, Class-T up to 20,000 Amps), these fuse holders are ideal for protecting today's demanding onboard power electronics technology including inverters and battery chargers. They also protect wiring from short circuits. Pro Installer fuse holders' durable construction allow fuses to run at maximum load. Radiused ends improve cable routing options Class-T: 225-400 Amp WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Fuse Type: Class T Type: Fuse Blocks Box Dimensions: 2"H x 7"W x 8"L WT: 0.95 lbs UPC: 870216043500 Brochure (pdf)

Read more less

8023 DC 8 Position Circuit Breaker - White SwitchesFeatures: All positive, negative and grounding buses installed, fully pre-wired Panels with meters include toggle switch for mounting up to 3 battery banks All panels with analog meters are owner upgradable to 24 Volts with 8240 or 8243 (18-32V DC meters) All circuit label positions are backlit on standard panels - No kit required "ON" indicating LEDs installed in all circuit positions Specifications: Positions: 8 Nominal Voltage: 12v / 24v DC Maximum Amperage: 100A Height: 7.5" Width: 5.25" Included: (5) 7210 A-Series White Toggle Circuit Breaker - Single Pole 15A (1) 8030 Basic DC Panel Label Set - 30 Labels WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Max Breaker Quantity: 8 AC/DC: DC Voltage: 12/24v Box Dimensions: 5"H x 7"W x 12"L WT: 2 lbs UPC: 632085080235 Owner's Manual (pdf)

Read more less

Multi RS Solar 48/6000 Inverter/ChargerThe Multi RS Solar 48/6000 is a 48V 6kVA inverter/charger with two independent 3kWp PV 450V MPPT trackers for 6kWp total panel capacity. It supports direct grid connection without batteries—perfect for starting simple and adding storage later.Updated in mid-2023 to a dual tracker design, its high-frequency technology delivers exceptional efficiency in a quiet, lightweight package with low standby power. Monitor all parameters via the integrated display or the VictronConnect app, which also provides historical trends, firmware updates, and configuration tools. Connect to a Cerbo GX for advanced ESS functions, like zero-export to block grid feed-in and backup mode to power critical loads during outages.Operating Modes: Hybrid mode – Stores excess solar energy in a battery, to be used during the night or periods of high demand. Supplies additional power from the battery when demand exceeds grid capacity. Backup mode – Switches to backup mode during a grid outage. Off-grid mode – Operates without a grid connection. Generator mode – Controls the generator to minimize run hours. Supplies additional power from the battery when demand exceeds the capacity of the generator. PV Inverter mode – Works as a PV inverter without a battery. PowerControl & PowerAssist - Boosting the capacity of the grid or a generatorA maximum grid or generator current can be set. The Multi RS will then take account of other AC loads and use whatever is extra for battery charging, thus preventing the generator or grid from being overloaded (PowerControl function).PowerAssist takes the principle of PowerControl to a further dimension. Where peak power is so often required only for a limited period, the Multi RS will compensate insufficient generator or grid power with power from the battery. When the load reduces, the spare power is used to recharge the battery.Display, Bluetooth & VictronConnect app The display reads battery, inverter and solar parameters. The same parameters can be accessed with a smartphone or other Bluetooth enabled device , using the VictronConnect app.Extendable PV capacity, both AC -coupled & DC -coupledThe integrated 6 kWp PV capacity can be extended by adding solar chargers to the system. Alternatively, the PV capacity can be extended by installing PV Inverters, of which the output power will be automatically controlled by the integrated frequency shift power control.Communication Ports VE.Can connection to a GX device for system monitoring, energy meter (11), data logging, and remote firmware updates.VE.Direct connection to a GlobalLink 520 for remote data monitoring. I/O ConnectionsProgrammable relay, temperature sensor and voltage sensor connectionsPlease contact your dealer for any returns, repairs or support issues related to this product. Quick Guide (pdf)Owner's Manual (pdf)Brochure (pdf)

Read more less

Orion-Tr Smart 12/48-8A (380W) Isolated DC-DC Charger The Orion-Tr Smart DC-DC charger is a professional DC to DC adaptive 3-stage charger with built-in Bluetooth.For use in dual battery systems in vehicles or on boats where the (smart) alternator and the start battery are used to charge the service battery. The unit can be monitored and programmed via Bluetooth and can be remotely controlled via a remote on/off switch and has an engine running detection mechanism.The Orion-Tr Smart charger can be used in 12V or 24V systems and is suitable for both lead acid and lithium batteries. Models are available up to 400W and unlimited multiple units can be connected in parallel to increase output power.Suitable for high temperatures up to 55°C with a full rated output up to 40°C.Bluetooth Smart enabled Any Bluetooth-enabled smartphone, tablet, or other device can be used to monitor, change settings, and update the charger when new software features become available. Instant Readout: The VictronConnect App can display key data, including warnings and alarms, on the Device list page without the need to connect to the product. Fully programmable Battery charge algorithm (configurable) or fixed output. Smart alternator compatibility: engine running detection mechanism. Adaptive 3-stage charge algorithm: bulk – absorption – float For lead acid batteries, it is important that during shallow discharges the absorption time is kept short to prevent overcharging of the battery. After a deep discharge, the absorption time is automatically increased to make sure that the battery is completely recharged. For lithium batteries absorption time is fixed, default 2 hours. Alternatively, a fixed output voltage can be chosen. Suitable for use in vehicles with a smart alternator (Euro 5 and Euro 6 engines)The built-in engine shutdown detection will stop the converter when the engine is not running. This prevents unwanted discharge of the starter battery.Remote on/offA remote on/off switch or relay contact can be connected to a two-pole connector. Alternatively, the H terminal (right) of the two-pole connector can be switched to battery plus, or the L terminal (left) of the two-pole connector can be switched to battery minus (or the chassis of a vehicle, for example).All models are short circuit proof and can be paralleled to increase output currentAn unlimited number of units can be connected in parallel.High temperature protectedThe output current will reduce at high ambient temperatures.IP43 protectionWhen installed with the screw terminals oriented downward.Screw terminalsNo special tools are needed for installation.Input fuse (not replaceable)Please contact your dealer for any returns, repairs or support issues related to this product. Quick Guide (pdf)Owner's Manual (pdf)Brochure (pdf)

Read more less

Lynx Distributor with M10 TerminalsThe Lynx Distributor contains a positive and a negative busbar. The positive busbar has four fuse-protected connections with fuse monitoring. The negative busbar has four connections and a ground connection. This model is part of the Lynx distribution and is a M10 busbar model. Note that M10 refers to the busbar connection joints where the modules are connected. The fuse and cable connections are always M8.The Lynx Distributor has a power LED and four fuse status indication LEDs. If connected to a Lynx Smart BMS, up to 4 Lynx Distributors can send fuse status information to the Lynx Smart BMS. This feature is not available when connected to a Lynx Shunt VE.Can.Features: 1000A model with M10 busbars The Lynx Distributor ships together with a 40cm RJ10 cable, which provides power to the Lynx Distributor and is also used to transmit data if connected to a Lynx Smart BMS The Lynx Distributor is designed to hold MEGA fuses If the Lynx Distributor is connected to a Lynx Smart BMS, it can be monitored and set up with the VictronConnect App Up to 4 connected Lynx distributors can be monitored with a GX device if connected to a Lynx Smart BMS The Lynx Distribution SystemThe Lynx Distribution System is a modular busbar system that incorporates DC connections, distribution, fusing, and battery monitoring and/or lithium battery management.The Lynx Distribution System Consists of the Following PartsLynx Power InA positive and negative busbar with four batteries or DC equipment connections.Lynx DistributorA positive and negative busbar with four fused connections for batteries or DC equipment and fuse monitoring, is available in two versions.Lynx Shunt VE.CanA positive busbar with a space for a main system fuse and a negative busbar with a shunt for battery monitoring. It has VE.Can communication for monitoring and setup with a GX device.Lynx Smart BMSFor use together with Victron Energy Smart Lithium batteries. It contains a positive busbar with a contactor driven by a battery management system (BMS) and a negative busbar with a shunt for battery monitoring.It has Bluetooth communication for monitoring and setup via the VictronConnect App and VE.Can communication for monitoring with a GX device and the VRM portal. Available as a 1000A model with M10 busbars.Please contact your dealer for any returns, repairs or support issues related to this product. Quick Guide (pdf)Owner's Manual (pdf)

Read more less