V4/V5 Windlass Gypsy #203 Replacement gypsy on Windlass Model V4/V5Features: Rope-chain gypsy Cone clutch for smooth, easy control Manual Free Fall W.A.R.P Drum Robust and reliable drivetrain Manual override (optional) Technical Specifications: Rope Size - 5/8" (16 mm) (3 strand hard lay up) Chain Size - 3/8" (10 mm) ( Campbell S3, Lewmar 9.5mm G40) *Sold as an Individual 

Read more less

Lewmar USA Premium 8-Plaited Nylon Anchor Rope 8-Plaited nylon rope eliminates some of the service problems associated with the 3-strand ropes. 8-Plait uses 8-individual braided strands woven together that allow the rope to be relaxed. But, when under load, it tightens up to a firm lay. The higher the load the harder the lay becomes. 8-Plait carries the same tensile strength as 3-Strand. 8-Plait does not coil or create a "birds nest" in the locker like 3-Strand will. 8-Plait flakes and falls upon itself. 8-Plait will not twist and knot up. 8-Plait will not loop over onto itself. 8-Plait has less stretch so it will not bury itself deep into the gypsy's grip when overloaded, which means less damage to the stripper when the windlass is abused or overloaded. 8-Plait pays off of the windlass into the locker much like chain, allowing for better use of smaller locker designs. 8-Plait is 80% less prone to becoming stiff when used in salt water than 3-Strand. 8-Plait nylon rope is 1/3 more absorbent than 3-Strand rope. More absorbent means more weight; more weight means better fall into the anchor locker. 8-Plait should be soaked in water (salt or fresh - it does not matter) to pre-lubricate the rope so it can be used in the windlass initially. When rope is used dry and new, we have seen either slippage or sticking in the rope pocket of the gypsy. Once the rope is wet and used, it out performs the 3-Strand. The longer it is used the better it gets.

Read more less

DTX Anchor - Stainless Steel - 14lbThe DTX anchor fills the gap between the existing galvanized and stainless Delta® anchors.Made from 316 stainless steel, the DTX anchors feature exceptional anti-corrosion performance and the enhanced aesthetics that stainless anchors offer. Utilizing lead ballast encapsulated within the tip of the anchor to achieve the perfect center of gravity, the DTX offers the initial bite and holding reliability that users of our Delta® anchors have come to expect.Features: Self-launching Ordinary holding power  Lead-ballasted tip for fast setting Technical Specifications: Material - Stainless Steel Recommended Chain Size - 1/4" Weight - 14lb (6kg) In the Box: Anchor Instruction manual *Sold as an Individual Specifications: Color: Stainless Construction: Stainless Steel Weight (lbs): 14 Box Dimensions: 10"H x 10"W x 18"L WT: 20 lbs Brochure (pdf)

Read more less

Support System Lower Frame (in) Acrylic Colour Hatch Weight (lb) Acrylic Window Thickness (in) Self Supporting 9/16 Smoke Grey 5.5 5/16 Dimensions Length X (in) Width Y (in) Height Z (in) Radii R (in) Cut-Out Length X1 (in) Cut-Out Width Y1 (in) Cut-Out Radii R1 (in) 9 11/16 19 5/16 1 2 7/8 6 15/16 16 9/16 1 11/16 Mounting Instructions Fit to a flat surface with a maximum tolerance of +/- 1mm. Fastening size at hinge section use M6 (1/4 in). Fastening size for lower frame use 5mm CSK screw No.10 UNC 2 BA.

Read more less

Anchor Rode 15’ 5/16” G4 Chain with 150’ 5/8” Rope with ShackleAn anchor rode is an important part of the anchoring system, and sailors rely on it to connect the anchor to a boat. Lewmar anchor rodes are designed for exceptional performance. The strong nylon rope with a hot-dip-galvanized G4 chain makes the rope-to-chain transition smooth and promotes maximum efficiency in operation.*A shackle is included for a secure and convenient anchor attachment pointFeatures: High-strength, welded chain rated to high-test G4 specs  Hot-dip-galvanized chain links to minimize corrosion Calibrated for an even pitch Smooth rope-to-chain transition for seamless windlass operation Treated, windlass-grade, 5/8" 8-plait rope Fitted to all Lewmar windlasses and rope chain gypsies Works With:Pro-series, ProFish 100-, V1, 2 & 3, along with H2 & 3 windlassesSpecifications: Rope: 150 ft. 5/8" 8-plait rope Chain: 15 ft. 5/16” G4 chain Specifications: Chain - Diameter (Inches): 5/16" Chain - Length (Feet): 15' Rope Diameter (Inches): 5/8" Rope Length (Feet): 150' Box Dimensions: 13"H x 13"W x 13"L WT: 31.65 lbs UPC: 743683410970

Read more less

Lewmar 14lb DTX Stainless Steel Anchor Model: 0057206 Manufactured from 316 stainless steel Self launching Ordinary Holding Power certified Guaranteed for 3 years against breakage The new DTX anchor fills the gap between the existing galvanised and stainless Delta(R) anchors, allowing boat owners and builders to specify a stainless steel anchor for a significantly reduced outlay. Made from 316 stainless steel, the DTX anchors feature exceptional anti-corrosional performance and the enhanced aesthetics that stainless anchors offer. Utilising lead ballast encapsulated within the tip of the anchor to achieve the perfect centre of gravity, the DTX offers the initial bite and holding reliability that users of our Delta(R) anchors have come to expect.

Read more less

Lewmar HM15H150PX Anchor Rode 15 feet 5/16 G4 Chain with 150 feet 5/8 in 8 Plait LineModel: HM15H150PX8-Plaited nylon rope eliminates some of the service problems associated with the 3-strand ropes. 8-Plait uses 8-individual braided strands woven together that allow the rope to be relaxed. But

Read more less

Both the 3-Button Windlass Remote Kit and the 5-Button Windlass & Thruster Kit are easily retrofitted to existing installations and include a replaceable battery. The fobs float and are waterproof to IP67 (1 Meter deep). Using over one billion individual codes, our proprietry encryption scheme prevents false triggering from any other device or similar fob. And both kits include a Receiver that supports up to eight remote key fobs (additional fobs sold separately). Allows wireless remote operation (up/Down) of any solenoid switched windlass. FCC & CE certified Kit includes one wireless fob and one receiver Notes: Most Lewmar products utilize solenoids although some of our smaller products may not. If in doubt contact your Lewmar representative.

Read more less

Anchor Rode 15’ 5/16” G4 Chain with 150’ 9/16” RopeAn anchor rode is an important part of the anchoring system, and sailors rely on it to connect the anchor to a boat. Lewmar anchor rodes are designed for exceptional performance. The strong nylon rope with a hot-dip-galvanized G4 chain makes the rope-to-chain transition smooth and promotes maximum efficiency in operation.Features: High-strength, welded chain rated to high-test G4 specs  Hot-dip-galvanized chain links to minimize corrosion Calibrated for an even pitch Smooth rope-to-chain transition for seamless windlass operation Treated, windlass-grade, 3-strand, twisted nylon rope Fitted to all Lewmar windlasses and rope chain gypsies Works With:Pro-series, ProFish 100-, V1, 2 & 3, along with H2 & 3 windlassesSpecifications: Rope: 150 ft. 9/16 in. 3-strand nylon  Chain: 15 ft. 5/16” G4 chain Specifications: Chain - Diameter (Inches): 5/16" Chain - Length (Feet): 15' Rope Diameter (Inches): 9/16" Rope Length (Feet): 150' Rope Type: 3-Strand Nylon Box Dimensions: 12"H x 12"W x 12"L WT: 27.65 lbs UPC: 743683406256

Read more less

Lewmar 7LB LFX Anchoring Kitwith 10 feet G4 1/4 Chain 150 feet 1/2 in 8-Plait LineModel: 0058103Made from lightweight and strong

Read more less

Anchor Rode 215'-15' of 1/4" Chain & 200' of 1/2" Rope with ShackleThis Lewmar 215' anchor rode kit features 15 feet' of windlass chain spliced to 200' of 3-strand line and comes with a D shackle.Technical Specifications: Total Length - 215' Chain Length - 15' Chain Size - 1/4" Chain Type - G4 Rope Length - 200' Rope Size - 1/2" Rope Type - 3 Strand Shackle - 5/16" D *Sold as an Individual Specifications: Chain - Diameter (Inches): 1/4" Chain - Length (Feet): 15' Rope Diameter (Inches): 1/2" Rope Length (Feet): 200' Rope Type: 3-Strand Nylon Box Dimensions: 8"H x 8"W x 18"L WT: 20 lbs UPC: 743683406430

Read more less

Lewmar USA Premium 8-Plaited Nylon Anchor Rope 8-Plaited nylon rope eliminates some of the service problems associated with the 3-strand ropes. 8-Plait uses 8-individual braided strands woven together that allow the rope to be relaxed. But, when under load, it tightens up to a firm lay. The higher the load the harder the lay becomes. 8-Plait carries the same tensile strength as 3-Strand. 8-Plait does not coil or create a "birds nest" in the locker like 3-Strand will. 8-Plait flakes and falls upon itself. 8-Plait will not twist and knot up. 8-Plait will not loop over onto itself. 8-Plait has less stretch so it will not bury itself deep into the gypsy's grip when overloaded, which means less damage to the stripper when the windlass is abused or overloaded. 8-Plait pays off of the windlass into the locker much like chain, allowing for better use of smaller locker designs. 8-Plait is 80% less prone to becoming stiff when used in salt water than 3-Strand. 8-Plait nylon rope is 1/3 more absorbent than 3-Strand rope. More absorbent means more weight; more weight means better fall into the anchor locker. 8-Plait should be soaked in water (salt or fresh - it does not matter) to pre-lubricate the rope so it can be used in the windlass initially. When rope is used dry and new, we have seen either slippage or sticking in the rope pocket of the gypsy. Once the rope is wet and used, it out performs the 3-Strand. The longer it is used the better it gets.

Read more less

V2 & V3 Gypsy Stripper Kit 003This is designed as a replacement gypsy for Lewmar's V1 and V2 windlasses.Features: Line Size: 5/8 in. / 16 mm Line Type: 3-strand line

Read more less

V1/V2/V3 Gypsy and Stripper Kit (No. 002)Replacement gypsy and stripper for Lewmar V1, V2 and V3 windlasses and the obsolete model Concept 1 windlass. Compatible With: V1, V2, V3 and Concept 1 windlassesTechnical Specifications: Rope Size - 1/2" to 5/8 (13 to 15.8 mm) (3 strand) Chain Size - 5/16" (7.94 mm) (G4) *Sold as an Individual 

Read more less

Solenoid in Watertight Control Box - 12VHeavy-duty dual-direction solenoid that controls the up/down operations of Lewmar Concept 1 and V-Series windlasses. Features: Controls Up / Down operation Ideal for windlass installations in chain locker or other damp locations Nominal voltage - 12V *Sold as an Individual

Read more less

Lewmar 15LB LFX Alloy FlukeAnchorModel: 0058107 High-grade anodized aluminum components Lightweight and strong holding power Quickly disassembles for stowage No welds Adjustable shank/fluke angle dependent on sea-bed Easily replaceable parts The new Lewmar LFX fluke anchor is constructed from High-grade anodized aluminum components delivering a lightweight, stylish anchor with a powerful holding power.The FLX Quickly disassembles for stowage as well as making parts easily replaceable. The FLX has an adjustable angled fluke for faster setting in sand or mud seabeds making it the ideal secondary anchor.

Read more less

Size 10 Low Profile Deck HatchThe Low Profile Hatch has soft styling and sleek looks, ideal for use on a powerboat. Smaller ventilation hatches are suitable for any deck location on sailboats, while the larger sizes can be used as foredeck hatches on smaller to mid-size yachts.Features: Outside handles allow the hatch to be opened from on deck if it is not locked (Sizes 00, 03,10, 20 & 41 have no outside handle and can only be opened from the inside.) Low profile hatches open up to 180° (round hatches open to 170°) Friction levers hold the lid open in any position up to 95° Anodized aluminum frame for corrosion resistance Curved upper frame profile for strength as well as modern styling Technical Specifications: Support System - Self-supporting Color - Smoke Grey Weight - 4.9lbs Dimensions (L x W x H) - 13" x 13" x 1" Cut-Out Dimensions (L x W) - 10.25" x 10.25" *Sold as an Individual  Quick Guide (pdf)Owner's Manual (pdf)

Read more less

Lewmar's 3-strand rope is an economical choice for your windlass rode. Keep in mind, the windlass does not stow the rode in the anchor locker - gravity does. So make sure you have ample depth and volume in your anchor locker to accommodate the length of rode you have chosen. 3-Strand is typically 20-30% less expensive than premium plaited anchor line. 3-Strand line, when used in salt water, will stiffen over time. It can be soaked in a bucket of fresh water and fabric softener overnight (the longer the better) to bring back a more flexible condition. If this does not yield acceptable results, it should be replaced.

Read more less

Lewmar HM10H150PX Anchor Rode 10 feet 5/16 G4 Chain with 150 feet 5/8 in 8 Plait LineModel: HM10H150PX8-Plaited nylon rope eliminates some of the service problems associated with the 3-strand ropes. 8-Plait uses 8-individual braided strands woven together that allow the rope to be relaxed. But

Read more less

Lewmar LEWHM06HT150P Anchor Rode 6 feet 1/4 G4 Chain with 150 feet 1/2 in 8 Plait LineModel: HM06HT150P8-Plaited nylon rope eliminates some of the service problems associated with the 3-strand ropes. 8-Plait uses 8-individual braided strands woven together that allow the rope to be relaxed. But

Read more less

Its unique shank profile and ballasted tip make the Delta anchor self-launching. The low centre of gravity and self-righting geometry ensure that the Delta anchor will set immediately. Consistent and reliable in performance, the Delta anchor has Lloyd's Register Type Approval as a High Holding Power anchor and is specified as the primary anchor used by numerous National Lifeboat organizations. Also available in premium grade Duplex/High Tensile stainless steel. All Delta anchors are "guaranteed for life against breakage". Lloyd's Test Certification is available for individual Delta anchors by arrangement. **Damage by deformation or bending is not covered by this guarantee.

Read more less

Support System Lower Frame (in) Acrylic Colour Hatch Weight (lb) Acrylic Window Thickness (in) Self Supporting 9/16 Smoke Grey 4.9 5/16 Dimensions Length X (in) Width Y (in) Height Z (in) Radii R (in) Cut-Out Length X1 (in) Cut-Out Width Y1 (in) Cut-Out Radii R1 (in) 10 11/16 16 7/16 1 2 7/8 7 15/16 13 11/16 1 11/16 Mounting Instructions Fit to a flat surface with a maximum tolerance of +/- 1mm. Fastening size at hinge section use M6 (1/4 in). Fastening size for lower frame use 5mm CSK screw No.10 UNC 2 BA.

Read more less

Lewmar HM10HT125PX Anchor Rode 10 feet 1/4 G4 Chain with 125 feet 1/2 in 8 Plait LineModel: HM10HT125PX8-Plaited nylon rope eliminates some of the service problems associated with the 3-strand ropes. 8-Plait uses 8-individual braided strands woven together that allow the rope to be relaxed. But

Read more less

Support System Lower Frame (in) Acrylic Colour Hatch Weight (lb) Acrylic Window Thickness (in) Self Supporting 9/16 Smoke Grey 4.9 5/16 Dimensions Length (in) Width (in) Height (in) Radii (in) Cut-Out Length (in) Cut-Out Width (in) Cut-Out Radii (in) 13 13 1 2 7/8 10 1/4 10 1/4 1 11/16 Mounting Instructions Fit to a flat surface with a maximum tolerance of +/- 1mm. Fastening size at hinge section use M6 (1/4 in). Fastening size for lower frame use 5mm CSK screw No.10 UNC 2 BA.

Read more less

185mm x 6mm x 1000mm fiberglass tube for 185tt thrusters.

Read more less

The Low Profile hatches have soft styling and sleek looks. They are ideal for use on power craft. Smaller ventilation hatches are suitable for any deck location on sailboats and the larger hatches can even be used as foredeck hatches. The hatch also features Lewmar's unique sealing system allowing easy acrylic replacement Specifications Support System Lower Frame (in) Acrylic Colour Hatch Weight (lb) Acrylic Window Thickness (in) Self Supporting 9/16 Smoke Gray 3.5 5/16 Dimensions Length X (in) Width Y (in) Height Z (in) Radii R (in) Cut-Out Length X1 (in) Cut-Out Width Y1 (in) Cut-Out Radii R1 (in) 9 11/16 11 7/8 1 2 7/8 6 15/16 9 1/8 1 11/16

Read more less

Generation 2 Single Joystick Thruster ControllerLewmar’s range of thruster controls provides superior tactile control of single or dual thruster installations. The controllers are installed without the need for rear access and feature a snap-on bezel to neatly hide the mounting screws.  A cover is also included, providing additional security against accidental use and giving extra environmental protection.  If replacing a previous generation touch panel, joystick panel, or dual joystick panel, the existing mounting hole and fixing screw positions can be reused. Compatible with:Lewmar TT, RT, SRT & VRT thrusters are fitted with a blue box and can be fitted to thrusters fitted with a black box using a controller adapter.*Requires Lewmar connecting cable.Features: The ergonomic control ‘pad’ gives tactile feedback  Membrane switch panel sealed from dust and moisture ingress  Multi-function LED indicator displays system deployment, thruster operation, low voltage, motor temperature warnings & fault conditions.  Fit existing cut-out of Lewmar joysticks  Removable cover  Technical Specifications: Power - 12/24 Volt DC Cut-out - 2.5" Diameter *Sold as an Individual Owner's Manual (pdf)

Read more less

The Low Profile hatches have soft styling and sleek looks. They are ideal for use on power craft. Smaller ventilation hatches are suitable for any deck location on sail boats and the larger hatches can even be used as foredeck hatches on smaller to mid size yachts Specifications Support System Lower Frame (in) Acrylic Colour Hatch Weight (lb) Acrylic Window Thickness (in) Self Supporting 9/16 Smoke Grey 3.5 5/16 Dimensions Length X (in) Width Y (in) Height Z (in) Radii R (in) Cut-Out Length X1 (in) Cut-Out Width Y1 (in) Cut-Out Radii R1 (in) 11 1/16 11 1/16 1 2 7/8 8 5/16 8 5/16 1 11/16

Read more less

Lewmar Single JoystickModel: 589268 Ergonomic control 'pad' gives tactile feedback Membrane switch panel sealed from dust and moisture ingress Single and dual controllers available Dual controllers give total control of vessel via multi-axis function pad 12-24V dual voltage supply Multi-function LED indicator displays system deployment, thruster operation, low voltage, motor temperature warnings & fault conditions. Upgrade kit allows installation of single or dual controllers into a thruster system with previous generation controllers Fit existing cut-out of Lewmar joysticks Removable cover Lewmar's new range of thruster controls provides a superior tactile control of single or dual thruster installations.The controllers are designed for all Lewmar TT, RT, SRT & VRT thrusters fitted with a blue box and can be fitted to thrusters fitted with a black-box using a controller adapter.The controllers are installed without the need for rear access and feature a snap-on bezel to neatly hide the mounting screws. A cover is also included, providing additional security against accidental use and giving extra environmental protection. If replacing a previous generation touch panel, joystick panel or dual joystick panel, the existing mounting hole and fixing screw positions can be reused.Specifications<table style='border-collapse: collapse' width='95%' border='1 feet>Range of controllers for Lewmar TT thruster range

Read more less

Upgraqde you Pro series windlass to a Profish free fall windlass witht his kit.

Read more less

Generation 3 Pro-Series Gears and Shaft Kit Gears and shaft kit for Generation 3 Pro-Series windlasses.Compatible With: Pro-Series Generation 2 windlasses*Sold as an Individual 

Read more less

Lewmar 589222 Gen2 Dual Thruster Control PadModel: 589222 Ergonomic control 'pad' gives tactile feedback Membrane switch panel sealed from dust and moisture ingress Dual controllers give total control of vessel via multi-axis function pad 12-24V dual voltage supply Multi-function LED indicator displays system deployment, thruster operation, low voltage, motor temperature warnings & fault conditions. Upgrade kit allows installation of single or dual controllers into a thruster system with previous generation controllers Fit existing cut-out of Lewmar joysticks Removable cover The controllers are designed for all Lewmar TT, RT, SRT & VRT thrusters fitted with a blue box and can be fitted to thrusters fitted with a black-box using a controller adapter.The controllers are installed without the need for rear access and feature a snap-on bezel to neatly hide the mounting screws. A cover is also included, providing additional security against accidental use and giving extra environmental protection. If replacing a previous generation touch panel, joystick panel or dual joystick panel, the existing mounting hole and fixing screw positions can be reused.

Read more less

Available  Special Order Please allow 2-3 weeks for delivery. (Temporary) No Overnight  Shipping available . Lewmar Shallow Water Anchor Jack Plate Mounting Bracket This bracket is designed to mount your Axis or Vector shallow water anchor to your jack plate. This mounting bracket features a symmetrical design so it can be mounted on either the port or starboard side. This bracket comes with all required mounting hardware.   Product MPN: 2024028460  Black PDF Manual    

Read more less

Lewmar HM15H125PX Anchor Rode 15 feet 5/16 G4 Chain with 125 feet 5/8 in 8 Plait LineModel: HM15H125PX8-Plaited nylon rope eliminates some of the service problems associated with the 3-strand ropes. 8-Plait uses 8-individual braided strands woven together that allow the rope to be relaxed. But

Read more less

Lewmar's 3-strand rope is an economical choice for your windlass rode. Keep in mind, the windlass does not stow the rode in the anchor locker - gravity does. So make sure you have ample depth and volume in your anchor locker to accommodate the length of rode you have chosen. 3-Strand is typically 20-30% less expensive than premium plaited anchor line. 3-Strand line, when used in salt water, will stiffen over time. It can be soaked in a bucket of fresh water and fabric softener overnight (the longer the better) to bring back a more flexible condition. If this does not yield acceptable results, it should be replaced.

Read more less

Lewmar Single PadModel: 589223 Ergonomic control 'pad' gives tactile feedback Membrane switch panel sealed from dust and moisture ingress Single and dual controllers available Dual controllers give total control of vessel via multi-axis function pad 12-24V dual voltage supply Multi-function LED indicator displays system deployment, thruster operation, low voltage, motor temperature warnings & fault conditions. Upgrade kit allows installation of single or dual controllers into a thruster system with previous generation controllers Fit existing cut-out of Lewmar joysticks Removable cover Lewmar's new range of thruster controls provides a superior tactile control of single or dual thruster installations.The controllers are designed for all Lewmar TT, RT, SRT & VRT thrusters fitted with a blue box and can be fitted to thrusters fitted with a black-box using a controller adapter.The controllers are installed without the need for rear access and feature a snap-on bezel to neatly hide the mounting screws. A cover is also included, providing additional security against accidental use and giving extra environmental protection. If replacing a previous generation touch panel, joystick panel or dual joystick panel, the existing mounting hole and fixing screw positions can be reused.

Read more less

Its unique shank profile and ballasted tip make the Delta anchor self-launching. The low centre of gravity and self-righting geometry ensure that the Delta anchor will set immediately. Consistent and reliable in performance, the Delta anchor has Lloyd's Register Type Approval as a High Holding Power anchor and is specified as the primary anchor used by numerous National Lifeboat organizations. Also available in premium grade Duplex/High Tensile stainless steel. All Delta anchors are "guaranteed for life against breakage". Lloyd's Test Certification is available for individual Delta anchors by arrangement. **Damage by deformation or bending is not covered by this guarantee.

Read more less