M8 Circular Connector 3-Pole BMS BTV Extension Cables - Pair - 2MFeatures: 2-meter cable Extends the data cables that run from a 12.8 Volt Lithium-Ion battery to the BMS Please contact your dealer for any returns, repairs or support issues related to this product. Quick Guide (pdf)

Read more less

Busbar to Connect 6 Modular HoldersFeatures: Six position high current bus bar (1500 A) With two M10 input connections. Input current up to 2000 A. Recommended to parallel multiple high power Multi or Quattro inverter/chargers Warranty InfoWARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.Please contact your dealer for any returns, repairs or support issues related to this product. Quick Guide (pdf)

Read more less

BlueSolar MPPT Charge Controller - 75V - 10AMPFeatures: Ultra-fast Maximum Power Point Tracking (MPPT) Especially in case of a clouded sky, when light intensity is changing continuously, an ultra-fast MPPT controller will improve energy harvest by up to 30% compared to PWM charge controllers and by up to 10% compared to slower MPPT controllers.  Load output Over-discharge of the battery can be prevented by connecting all loads to the load output. The load output will disconnect the load when the battery has been discharged to a pre-set voltage. Alternatively, an intelligent battery management algorithm can be chosen: see Battery Life. The load output is short circuit proof. Some loads (especially inverters) can best be connected directly to the battery, and the inverter remote control connected to the load output. A special interface cable may be needed, please see the manual.  Battery Life: intelligent battery management When a solar charge controller is not able to recharge the battery to its full capacity within one day, the result is often that the battery will continually be cycled between a ‘partially charged’ state and the ‘end of discharge’ state. This mode of operation (no regular full recharge) will destroy a lead-acid battery within weeks or months. The Battery Life algorithm will monitor the state of charge of the battery and, if needed, day by day slightly increase the load disconnect level (i.e. disconnect the load earlier) until the harvested solar energy is sufficient to recharge the battery to nearly the full 100%. From that point onwards the load disconnect level will be modulated so that a nearly 100% recharge is achieved about once every week.  Programmable battery charge algorithm See the software section on our website for details  Day/night timing and light dimming option See the software section on our website for details  Programming, real-time data and history display options - Color Control GX or other GX devices: see the Venus documents on our website. - A smartphone or other Bluetooth-enabled device: VE.Direct Bluetooth Smart dongle needed Warranty InfoWARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.Please contact your dealer for any returns, repairs or support issues related to this product. Specifications: Charger Input - Voltage: 18-75v Charger Output - Amps: 10a Charger Output Voltage: 12v/24v Charging Banks: 1 Portable: No Box Dimensions: 2"H x 6"W x 7"L WT: 0.8 lbs UPC: 8719076025306 Quick Guide (pdf)Brochure (pdf)

Read more less

Argo Diode Battery Combiner - 80AMP - 2 BatteriesDiode Battery Combiners are used to guarantee continuous DC power to mission critical equipment, such as an electronic engine control system. With a Diode Battery Combiner two or more DC power sources can be used in parallel to supply the mission critical load. Failure of one source will not interrupt power to the critical load.Warranty InfoWARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.Please contact your dealer for any returns, repairs or support issues related to this product. Quick Guide (pdf)Brochure (pdf)

Read more less

M8 Circular Connector 3-Pole BMS BTV Extension Cables - Pair - 1MFeatures: 1-meter cable Extends the data cables that run from a 12.8 Volt Lithium-Ion battery to the BMS Please contact your dealer for any returns, repairs or support issues related to this product. Quick Guide (pdf)

Read more less

Busbar 250A 2P with 6 Screws & CoverBusbars are used for high current distribution and at the same time they provide connections for batteries and/or DC equipment.We offer a number of busbars with different current ratings, and a different number of connection terminals. Each busbar is fitted out with a removable protective cover. Quick Guide (pdf)

Read more less

ANL-Fuse 500A/80V (Package of 5)Victron Energy's ANL fuses are bolt-down, fast-acting, and have a higher short-circuit breaking capability than MEGA fuses. This particular pack of Victron ANL fuses contains FIVE 500-amp fuses.Specifications: Max Current Rating: 500 amps Max Voltage Rating: 80 volts Approximate Voltage Drop: 125mV Cold resistance: 0,25 mΩ Please contact your dealer for any returns, repairs or support issues related to this product.

Read more less

ANL-Fuse 400A/80V for 48V Products (Package of 5)Victron Energy's ANL fuses are bolt-down fast-acting and have a higher short-circuit breaking capability than MEGA fuses. This particular pack of Victron ANL fuses contains FIVE 400-amp fuses.Features:For 48V productsSpecifications: Max Current Rating: 400 amps Max Voltage Rating: 80 volts Approximate Voltage Drop: 125 mV Cold Resistance: 0.3 mΩ Please contact your dealer for any returns, repairs or support issues related to this product. Specifications: Amperage: 400a Fuse Type: ANL Type: Fuses Box Dimensions: 1"H x 5"W x 6"L WT: 0.3 lbs UPC: 8719076061786 Quick Guide (pdf)Brochure (pdf)

Read more less

ANL-Fuse 300A/80V for 48V Products (Package of 5)Victron Energy's ANL fuses are bolt-down fast-acting and have a higher short-circuit breaking capability than MEGA fuses. This particular pack of Victron ANL fuses contains five 300-amp fuses.Specifications: Max Current Rating: 300 amps Max Voltage Rating: 80 volts Approximate Voltage Drop: 125 mV Cold Resistance: 0.35 mΩ Please contact your dealer for any returns, repairs or support issues related to this product. Specifications: Amperage: 300a Fuse Type: ANL Type: Fuses Box Dimensions: 2"H x 2"W x 4"L WT: 0.25 lbs UPC: 8719076061779 Quick Guide (pdf)Brochure (pdf)

Read more less

Argodiode Battery Isolator 80-2SC - 2 Batteries - 80AArgodiode Battery Isolators allow simultaneous charging of two or more batteries from one alternator, without connecting the batteries. Discharging the accessory battery for example will not result in also discharging the starter battery. Low voltage drop due to the use of high-efficiency Schottky diodes.The Argo Battery Isolators feature a low voltage drop thanks to the use of Schottky diodes: at low current, the voltage drop is approximately 0,3 V, and at the rated output of approximately 0,45 V. All models are fitted with a compensation diode that can be used to slightly increase the output voltage of the alternator. This compensates for the voltage drop over the diodes in the isolator. Simply inserting the isolator in the cabling between the alternator and the batteries will slightly reduce charge voltage. The result can be that batteries are not charged to the full 100% and age prematurely. Alternator energize input Some alternators need DC voltage on the B+ output to start charging. Obviously, DC will be present when the alternator is directly connected to a battery. Inserting a Diode or FET splitter will however prevent any return voltage/current from the batteries to the B+, and the alternator will not start. The new ‘AC’ diode isolators feature a special current limited energize input that will power the B+ when the engine run/stop switch is closed.Please contact your dealer for any returns, repairs or support issues related to this product. Quick Guide (pdf)

Read more less

SolidSwitch 104 for DC Loads Up To 70V/4AFeatures: The SolidSwitch 104 will switch DC loads of up to 70V/4A and can be controlled by a low-power digital signal. The DC load can be resistive, capacitive or inductive (such as the coil of a high-power contactor). The SolidSwitch is not reverse polarity protected and not short circuit proof. Please contact your dealer for any returns, repairs or support issues related to this product. Quick Guide (pdf)Brochure (pdf)

Read more less

Smart Battery Sense Long Range (Up to 10M)The VE.Bus Smart dongle is a Bluetooth Smart enabled VE.Bus interface, with battery temperature-and-voltage sensing. It communicates system information straight to your smart phone - using the free-to-use VictronConnect app.  When used with Multi- inverter/chargers the dongle provides on-battery temperature and voltage sensing capabilities - allowing compensation for possible cable losses which can occur during charging and discharging. Temperature sensing allows accurate temperature-compensation during battery charge cycles. The dongle is, at present, the only way to add an “on-battery” sensing capability to the MultiPlus-II models, if they are not also connected to a GX device and CANbus battery.The dongle can be used in systems with or without a GX device - such as the CCGX. In systems with a GX device, and another source of temperature and voltage data (eg from a CANbus battery), the CCGX data will override temperature and voltage information from the dongle. In this role the dongle will still provide live-information via its VictronConnect interface; and it will provide firmware updates without requiring an internet connection.When the dongle is used in systems which do not have a GX device, the dongle's voltage and temperature data becomes the primary source of that information, and can be used by other connected devices for voltage compensation.In systems with a Multiplus-II, dongle and GX device, but no other source of temperature and voltage, the data from the dongle will also be used.At this time, the VE.Bus Smart dongle cannot send its temperature and voltage data as part of a VE.Smart network.The VE.Bus Smart dongle is able to sense battery temperature in two ways: The default method is the dongle's on-board temperature sensor. When the dongle is mounted directly onto the battery case (using its adhesive attachment) it will sense the battery temperature directly from the battery casing. The second method - which provides improved battery temperature sensing - is available by using an optional battery-terminal mounted sensor. When this sensor is connected, the default sensor is overridden and the dongle will use this method instead.What's in the Box? VE.Bus Smart Dongle Red battery (+) connection wire with 10mm eyelet and inline fuse. Black battery (-) connection wire with 10mm eyelet Connector block with screw terminals Warranty InfoWARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.Please contact your dealer for any returns, repairs or support issues related to this product. Quick Guide (pdf)

Read more less

Busbar to Connect 5 Mega Fuse Holders Busbar Only Fuse Holders Sold SeparatelyPlease contact your dealer for any returns, repairs or support issues related to this product. Quick Guide (pdf)

Read more less

MagCode Power Port for Blue Smart IP65 Charger - 12V - 15 Amp Max (Requires Power Clip)MagCode Power Port is a magnetic connector for Victon's Blue Smart IP65 Chargers.Specifications: Volt: 12V Max Amp: 15 *Requires Victon’s MagCode Power ClipPlease contact your dealer for any returns, repairs or support issues related to this product. Quick Guide (pdf)

Read more less

VE. Direct Bluetooth Smart DongleUsing the VE.Direct to Bluetooth Smart dongle you can display your BMV or MPPT information on iOS and Android devices, using the VictronConnect app. View information wirelessly such as battery status and solar panel power, plus other useful data. The dongle is able to read data from all products with a VE.Direct port, such as the BMV-70x series battery monitors, Phoenix Inverters with VE.Direct port, MPPT Solar Charge Controllers.Warranty InfoWARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.Please contact your dealer for any returns, repairs or support issues related to this product. Quick Guide (pdf)Owner's Manual (pdf)

Read more less

Current Transformer 100A:50mA for MultiPlus-II 5M/16.4'The Current Transformer 100A:50mA is designed for use with the Victron MultiPlus-II and MultiGrid-II to enable advanced energy features such as PowerControl, PowerAssist, and self-consumption optimization through external current sensing.By accurately measuring external currents, this transformer allows the system to dynamically manage energy flows, helping to avoid overloading, reduce grid dependency, and make the most of available solar power.Features: Supports PowerControl and PowerAssist functions Enables self-consumption optimization Rated for 100A:50mA; 400A:50mA Compatible with MultiPlus-II Please contact your dealer for any returns, repairs or support issues related to this product.

Read more less

BCD 402 Combiner Diode - 2 Batteries - 40A BCD402Diode Battery Combiners guarantee continuous DC power to mission-critical equipment, such as an electronic engine control system. With a Diode Battery Combiner, two or more DC power sources can be used in parallel to supply the mission-critical load. Failure of one source will not interrupt power to the critical load.The Argo Battery Combiners feature a low voltage drop thanks to the use of Schottky diodes: at low current, the voltage drop is approximately 0,3 V, and at the rated output approximately 0,45 V.Warning: hot surface, mount the Argo Diode Battery Combiner on a non-flammable surface only!Please contact your dealer for any returns, repairs or support issues related to this product. Quick Guide (pdf)

Read more less

RJ45 UTP - 30M CableA cable to connect Phoenix Inverter Control, VE Interface MK3-USB, and VE.Bus connections between multiple VE.Bus devices and GX devices.Warranty InfoWARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.Please contact your dealer for any returns, repairs or support issues related to this product. Quick Guide (pdf)

Read more less

BatteryProtect BP-65 - 65AMP - 6-35 VDCFeatures: The BatteryProtect disconnects the battery from non essential loads before it is completely discharged (which would damage the battery) or before it has insufficient power left to crank the engine.  12/24V auto ranging The BatteryProtect automatically detects system voltage  Programming made easy The BatteryProtect can be set to engage / disengage at several different voltages. The seven segment display will indicate which setting has been chosen.  A special setting for Li-ion batteries In this mode the BatteryProtect can be controlled by the VE.Bus BMS. Note: the BatteryProtect can also be used as a charge interrupter in between a battery charger and a Li-ion battery. See connection diagram in the manual.  Ultra low current consumption This is important in case of Li-ion batteries, especially after low voltage shutdown. Please see our Li-ion battery datasheet and the VE.Bus BMS manual for more information.  Over voltage protection To prevent damage to sensitive loads due to over voltage, the load is disconnected whenever the DC voltage exceeds 16V respectively 32V. Ignition proof No relays but MOSFET switches, and therefore no sparks. Delayed alarm output The alarm output is activated if the battery voltage drops below the preset disconnect level during more than 12 seconds. Starting the engine will therefore not activate the alarm. The alarm output is a short circuit proof open collector output to the negative (minus) rail, max. current 50 mA. The alarm output is typically used to activate a buzzer, LED or relay. Delayed load disconnect and delayed reconnect The load will be disconnected 90 seconds after the alarm has been activated. If the battery voltage increases again to the connect threshold within this time period (after the engine has been started for example), the load will not be disconnected. The load will be reconnected 30 seconds after the battery voltage has increased to more than the preset reconnect voltage. Warranty InfoWARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.Please contact your dealer for any returns, repairs or support issues related to this product. Quick Guide (pdf)Brochure (pdf)

Read more less

MPPT WireBox-L Tr 150-60/70 & 250-60/70The MPPT WireBox provides an extra level of safety and is particularly useful if your MPPT Solar Charger is installed in a general access area. It covers all DC terminals, preventing accidental or inquisitive contact with terminal screws.

Read more less

MPPT WireBox-XL Tr 150-85/100 & 250-85/100The MPPT WireBox provides an extra level of safety and is particularly useful if your MPPT Solar Charger is installed in a general access area. It covers all DC terminals, preventing accidental or inquisitive contact with terminal screws.Please contact your dealer for any returns, repairs or support issues related to this product.

Read more less

6-Way Mega Fuse Holder with Busbar - 250ASix-way fuse holder for mega-style fuses with busbar (250A)Warranty InfoWARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.Please contact your dealer for any returns, repairs or support issues related to this product. Specifications: Type: Fuse Blocks Fuse Type: MEGA/AMG Amperage: 250a Box Dimensions: 2"H x 6"W x 8"L WT: 1.2 lbs UPC: 8719076051350 Quick Guide (pdf)Brochure (pdf)

Read more less

Wall Mount Enclosure for Color Control GX & BMV or MPPT ControlWall Mount for CCGX and BMV or MPPT Control easily mounts a CCGX and a BMV-700 series or MPPT Control on a wall. WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.Please contact your dealer for any returns, repairs or support issues related to this product. Quick Guide (pdf)

Read more less

Modular Fuse Holder for MEGA FuseThe dovetail feature allows interlocking multiple fuse holders.Warranty InfoWARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.Please contact your dealer for any returns, repairs or support issues related to this product. Specifications: Fuse Type: MEGA/AMG Type: Fuse Holders Box Dimensions: 1"H x 2"W x 3"L WT: 0.3 lbs UPC: 8719076018124 Quick Guide (pdf)Brochure (pdf)

Read more less

BlueSolar PWM-Light Charge Controller - 12/24V - 20AMPFeatures: Load output with low battery voltage disconnect function. Lighting control function, one timer only.  Two digit seven segment display for quick and easy setting of the load output functionality, including timer setting.  Three stage battery charging (bulk, absorption, float), not programmable. Load output protected against over load and short circuit. Protected against reverse polarity connection of the solar array and/or battery. Day/night timing options: see manual for details Warranty InfoWARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.Please contact your dealer for any returns, repairs or support issues related to this product. Quick Guide (pdf)Brochure (pdf)

Read more less

Battery Switch 275A 12-48VDC Surface or Panel MountThe Battery Switch ON/OFF 275A is suitable for battery systems up to 48V. It has a unique ergonomic and aesthetic knob design. The knob is removable for isolation or safety purposes.The Battery Switch can be either surface or panel mounted, providing flexibility during install.The Battery Switch meets the ISO8846 Ignition Protection standard and is suitable for use in an engine room.Please contact your dealer for any returns, repairs or support issues related to this product. Quick Guide (pdf)Brochure (pdf)

Read more less

Carry Case for BlueSmart IP65 Chargers & AccessoriesSmart and professional; this new snap shut carry case provides protective stowage and easy transport for your Blue Smart IP65 charger, and its accessories.Compartments accommodate the charger, its input/output cables; plus the battery-clamp/eyelet cable options.*Charger and accessories not includedWarranty InfoWARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.Please contact your dealer for any returns, repairs or support issues related to this product. Specifications: Type: Chargers Box Dimensions: 4"H x 12"W x 14"L WT: 1.95 lbs UPC: 8719076046554 Quick Guide (pdf)Brochure (pdf)

Read more less

Current Transformer 100A:50mA for MultiPlus-II 1M/3.2' Wire EndThe Current Transformer 100A:50mA is designed for use with the Victron MultiPlus-II and MultiGrid-II to enable advanced energy features such as PowerControl, PowerAssist, and self-consumption optimization through external current sensing.By accurately measuring external currents, this transformer allows the system to dynamically manage energy flows, helping to avoid overloading, reduce grid dependency, and make the most of available solar power.Features: Supports PowerControl and PowerAssist functions Enables self-consumption optimization Rated for 100A:50mA; 400A:50mA Compatible with MultiPlus-II Please contact your dealer for any returns, repairs or support issues related to this product.

Read more less

Current Transformer 100A:50mA for MultiPlus-II 1M/3.28'The Current Transformer 100A:50mA is designed for use with the Victron MultiPlus-II and MultiGrid-II to enable advanced energy features such as PowerControl, PowerAssist, and self-consumption optimization through external current sensing.By accurately measuring external currents, this transformer allows the system to dynamically manage energy flows, helping to avoid overloading, reduce grid dependency, and make the most of available solar power.Features: Supports PowerControl and PowerAssist functions Enables self-consumption optimization Rated for 100A:50mA; 400A:50mA Compatible with MultiPlus-II Please contact your dealer for any returns, repairs or support issues related to this product.

Read more less

SmartSolar Pluggable DisplayFeatures: The optional Victron SmartSolar MPPT Control Display is a pluggable LCD display for the SmartSolar Charge Controllers. Simply remove the rubber seal that protects the plug on the front of the controller and plug-in the display. Great add-on for Victron SmartSolar charge controllers Crystal clear display Mounting screws included Warranty InfoWARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.Please contact your dealer for any returns, repairs or support issues related to this product. Quick Guide (pdf)Brochure (pdf)

Read more less

RJ45 UTP - 20M CableA cable to connect Phoenix Inverter Control, VE Interface MK3-USB, and VE.Bus connections between multiple VE.Bus devices and GX devices.Warranty InfoWARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.Please contact your dealer for any returns, repairs or support issues related to this product. Quick Guide (pdf)

Read more less

Temperature Sensor for BMV-712 Smart & BMV-702Victron's Temperature Sensor specifically for the BMV-712 and the BMV-702.Warranty InfoWARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.Please contact your dealer for any returns, repairs or support issues related to this product. Quick Guide (pdf)

Read more less

MPPT WireBox-M 100 30/50 & 150-35/45The MPPT WireBox provides an extra level of safety and is particularly useful if your MPPT Solar Charger is installed in a general access area. It covers all DC terminals, preventing accidental or inquisitive contact with terminal screws.Please contact your dealer for any returns, repairs or support issues related to this product. Owner's Manual (pdf)

Read more less

MEGA-Fuse 250A/58V for 48V Products (Package of 1)Victron Energy's MEGA fuses are frequently used in Victron Energy DC distribution systems. This particular package contains ONE Victron MEGA 250 amp fuse that’s designed for 48V products.Specifications: Max Current Rating: 250 amps Max Voltage Rating: 58 volts Approximate Voltage Drop: 80 mV Cold Resistance: 0.2 mΩ Please contact your dealer for any returns, repairs or support issues related to this product. Specifications: Amperage: 250a Fuse Type: MEGA/AMG Type: Fuses Box Dimensions: 1"H x 4"W x 7"L WT: 0.05 lbs UPC: 8719076016700 Quick Guide (pdf)Brochure (pdf)

Read more less

MEGA-Fuse 200A/58V for 48V Products (Package of 1)Victron Energy's MEGA fuses are frequently used in Victron Energy DC distribution systems. This particular package contains ONE Victron MEGA 200 amp fuse that’s designed for 48V products.Specifications: Max Current Rating: 200 amps Max Voltage Rating: 58 volts Approximate Voltage Drop: 80 mV Cold Resistance: 0.25 mΩ Please contact your dealer for any returns, repairs or support issues related to this product. Specifications: Amperage: 200a Fuse Type: MEGA/AMG Type: Fuses Box Dimensions: 1"H x 4"W x 7"L WT: 0.05 lbs UPC: 8719076016694 Quick Guide (pdf)Brochure (pdf)

Read more less

Outdoor Antenna for GX LTE 4G-AThis antenna is optimized for 4G frequency bands and, as such, will have slightly better reception on the 4G network. It can be used with the GX LTE 4G for 2G, 3G, and 4G bands.If the 2G/3G variant does not provide sufficient signal quality in an installation, the solution is to contact a local GSM antenna provider. All the necessary information, including a link to the cellular modem (Simcom) used, can be found in this manual.Specifications: Mounting Option: Screw mount Cable Type: RG-316 Cable Length: 3.0 m Connector: SMA male straight Frequencies: 800/900/1800/1900/2100 MHz Signal Gain: 3 dBi Please contact your dealer for any returns, repairs or support issues related to this product. Quick Guide (pdf)Owner's Manual (pdf)

Read more less

Active GPS Antenna for GX LTE ModemThis antenna is for the GX LTE Modem.Specifications: Mounting Option: Magnet Cable Type: RG-74 Cable Length: 3.0 m Connector: SMA male straight Frequencies: 1575.42 MHz Signal Gain: 50 Ω Please contact your dealer for any returns, repairs or support issues related to this product. Quick Guide (pdf)Owner's Manual (pdf)

Read more less

Replacement 500A PCB for Shunt on BMV 702 & 712 MonitorsReplacement PCB only for 500 Amp shunt on BMV 702 & 712 MonitorsWarranty InfoPlease contact your dealer for any returns, repairs or support issues related to this product.

Read more less

Busbar 150A 2P with 20 Screws & CoverBusbars are used for high current distribution and at the same time they provide connections for batteries and/or DC equipment.We offer a number of busbars with different current ratings, and a different number of connection terminals. Each busbar is fitted out with a removable protective cover. Quick Guide (pdf)

Read more less

CCGX Wi-Fi Module Simple (Nano USB)Use to connect a Victron Color Control GX to a wireless network.  Enter the wireless ID and Passwords using the Color Control GX.Features: USB 2.0 interface Data rate 802.11n, 802.11g, 802.11b Frequency band 2.4 GHz Warranty InfoWARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.Please contact your dealer for any returns, repairs or support issues related to this product. Quick Guide (pdf)

Read more less

Ekrano GX Wall MountThis Victron wall mount will be especially useful if users like to keep the smart charger handy - perhaps above the workshop bench. Now users can use the charger without even moving it!Features:Wall mount for Victron Ekrano GXPlease contact your dealer for any returns, repairs or support issues related to this product.

Read more less

Busbar 150A 6P & Cover 6X 1/4" TerminalsBusbars are used for high current distribution and at the same time they provide connections for batteries and/or DC equipment.We offer a number of busbars with different current ratings, and a different number of connection terminals. Each busbar is fitted out with a removable protective cover. Quick Guide (pdf)

Read more less

VE. Direct to USB InterfaceThe VE.Direct to USB interface connects products with a VE.Direct connection to devices with a USB port, for example, a computer. With this cable, it is also possible to connect more than two VE.Direct products to a single CCGX. Measures 70.5" in length; 5' 10".WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.Please contact your dealer for any returns, repairs or support issues related to this product. Quick Guide (pdf)

Read more less

Battery Indicator Eyelet M8 (30A ATO Fuse)The Battery Indicator Eyelet M8 is an accessory for the Blue Smart IP65 Chargers. 0.3M cable length 12 AWG Max Current 20A Please contact your dealer for any returns, repairs or support issues related to this product. Specifications: Charger Input - Voltage: 12 Charger Output - Amps: 20 Charger Output Voltage: 12 Charging Banks: 1 Box Dimensions: 2"H x 3"W x 6"L WT: 0.45 lbs UPC: 8719076043072 Quick Guide (pdf)Brochure (pdf)

Read more less

VE Direct Cable - 10MThe VE.Direct cable is available in different lengths. There is a straight and 90 degree angle model.  Quick Guide (pdf)

Read more less

VE. Direct - 10M Cable (1 Side Right Angle Connector)Features: Cable Length: 10M 1 Side Right Angle Connector Warranty InfoWARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.Please contact your dealer for any returns, repairs or support issues related to this product. Quick Guide (pdf)

Read more less

RJ12 UTP Cable - 10MA cable to connect the BMV shunt to the BMV head unit. An RJ12 cable ships standard with a BMV battery monitor, but if this cable is too long or too short it can be replaced by one of these cables, lengths available from 0.3 up to 30 meters.Please contact your dealer for any returns, repairs or support issues related to this product. Quick Guide (pdf)

Read more less

GX Touch 50 Adapter for CCGX Cut-OutThis adapter is designed to easily replace the CCGX display with the newer GX Touch. Contents of the packaging are the metal bracket, the plastic bezel, and four mounting screws.There are two methods of mounting: “Install including screen” - most secure mounting of the GX Touch display “Install excluding screen” – GX Touch display is easier to remove, and the adapter can be mounted before completing the wiring Please contact your dealer for any returns, repairs or support issues related to this product. Quick Guide (pdf)

Read more less