FREE SHIPPING ON ORDERS OVER $100.0 Dollars!

Show previous products

  • Sale -$16.80 Victron Argodiode Battery Isolator 140-3AC - 3 Batteries - 140A [ARG140301020R]

    Victron Energy Victron Argodiode Battery Isolator 140-3AC - 3 Batteries - 140A [ARG140301020R]

    Argodiode Battery Isolator 140-3AC - 3 Batteries - 140AArgodiode Battery Isolators allow simultaneous charging of two or more batteries from one alternator, without connecting the batteries. Discharging the accessory battery for example will not result in also discharging the starter battery. Low voltage drop due to the use of high-efficiency Schottky diodes.The Argo Battery Isolators feature a low voltage drop thanks to the use of Schottky diodes: at low current, the voltage drop is approximately 0,3 V, and at the rated output of approximately 0,45 V. All models are fitted with a compensation diode that can be used to slightly increase the output voltage of the alternator. This compensates for the voltage drop over the diodes in the isolator. Simply inserting the isolator in the cabling between the alternator and the batteries will slightly reduce charge voltage. The result can be that batteries are not charged to the full 100% and age prematurely. Alternator energize input Some alternators need DC voltage on the B+ output to start charging. Obviously, DC will be present when the alternator is directly connected to a battery. Inserting a Diode or FET splitter will however prevent any return voltage/current from the batteries to the B+, and the alternator will not start. The new ‘AC’ diode isolators feature a special current limited energize input that will power the B+ when the engine run/stop switch is closed.Please contact your dealer for any returns, repairs or support issues related to this product. Quick Guide (pdf)

    Read more

    $112.00 $95.20

  • Sale -$16.65 Victron Phoenix Inverter 12/250 - 120V - VE.Direct GFCI Duplex Outlet - 200W [PIN122510510] Victron Phoenix Inverter 12/250 - 120V - VE.Direct GFCI Duplex Outlet - 200W [PIN122510510]

    Victron Energy Victron Phoenix Inverter 12/250 - 120V - VE.Direct GFCI Duplex Outlet - 200W [PIN122510510]

    Phoenix Inverter 12/250 - 120V - VE.Direct GFCI Duplex Outlet - 200WInverters allow users to power domestic equipment - requiring 230V/120V AC - using 'leisure' or 'automotive' batteries rated at 12V, 24V or 48V DC.*This inverter has a GFCI Duplex Outlet.E.Direct Communication PortThe VE.Direct port can be connected to: A computer (VE.Direct to USB interface cable needed) Apple and Android smartphones, tablets, MacBook, and other devices (VE.Direct Bluetooth Smart dongle needed) Fully Configurable: Low battery voltage alarm trip and reset levels Low battery voltage cut-off and restart levels Dynamic cut-off: load-dependent cut-off level Output voltage 210 - 245V Frequency 50 Hz or 60 Hz ECO mode on/off and ECO mode sense level Monitoring:In- and output voltage, % load, and alarmsProven ReliabilityThe full bridge plus toroidal transformer topology has proven its reliability over many years.The inverters are short-circuit proof and protected against overheating, whether due to overload or high ambient temperature.High Start-Up PowerNeeded to start loads such as power converters for LED lamps, halogen lamps, or electric tools.ECO ModeWhen in ECO mode, the inverter will switch to standby when the load decreases below a preset value (min load: 15W). Once on standby, the inverter will switch on for a short period (adjustable, default: every 2,5 seconds). If the load exceeds a preset level, the inverter will remain on.Remote On/OffA remote on/off switch can be connected to a two-pole connector, or between battery plus and the left-hand contact of the two-pole connector.LED DiagnosisPlease see the manual for a description.To Transfer the Load to Another AC Source: The Automatic Transfer SwitchFor Victron’s low-power inverters, they recommend the Filax Automatic Transfer Switch. The Filax features a very short switchover time (less than 20 milliseconds) so that computers and other electronic equipment will continue to operate without disruption. Inverter Specifications: Cont. Power at 25 degrees C: (1) 250VA  Cont. Power at 25 degrees C / 40 degrees C: 200 / 175W  Peak Power: 400W  Output AC Voltage / Frequency (adjustable): 230VAC or 120VAC +/- 3% 50Hz or 60Hz +/- 0,1% Input Voltage Range: 9,2 - 17 / 18,4 - 34,0 / 36,8 - 62,0V DC Low Shut Down (adjustable): 9,3 / 18,6 / 37,2V Dynamic (load dependent) DC Low Shut Down (fully configurable): Dynamic cut-off, see https://www.victronenergy.com/live/ve.direct:phoenix-inverters-dynamic-cutoff DC Low Restart & Alarm (adjustable): 10,9 / 21,8 / 43,6V Battery Charged Detect (adjustable): 14,0 / 28,0 / 56,0V Max. Efficiency: 87 / 88 / 88%  Zero-Load Power: 4,2 / 5,2 / 7,9W  Default Zero-Load Power in ECO Mode (default retry interval: 2,5 s, adjustable): 0,8 / 1,3 / 2,5W  ECO Mode Stop & Start Power Setting: Adjustable Protection (2): a - f Operating Temperature Range -40 to +65 degrees C (fan-assisted cooling)  Enclosure Specifications: Material & Color: Steel chassis and plastic cover (blue Ral 5012) Battery-Connection: Screw terminals Maximum Cable Cross-Section: 10mm² / AWG8  Standard AC Outlets: 230V: Schuko (CEE 7/4), IEC-320 (male plug included); UK (BS 1363), AU/NZ (AS/NZS 3112); 120V: Nema 5-15R, GFCI Protection Category: IP 21 Weight: 2,4kg / 5,3lbs  Dimensions (H x W x D, mm); (H x W x D, inch): 86 x 165 x 260; 3.4 x 6.5 x 10.2 Accessories: Remote On-off: Yes Automatic Transfer Switch: Filax Standards: Safety: EN-IEC 60335-1 / EN-IEC 62109-1 / UL 458 (3) EMC: EN 55014-1 / EN 55014-2 / IEC 61000-6-1 / IEC 61000-6-2 / IEC 61000-6-3 Automotive Directive ECE R10-4: 1) Nonlinear load, crest factor 3:1; 2) Protection key: a) output short circuit b) overload c) battery voltage too high d) battery voltage too low e) temperature too high f) DC ripple too high Please contact your dealer for any returns, repairs or support issues related to this product. Specifications: GFCI: Yes Box Dimensions: 6"H x 9"W x 13"L WT: 7.3 lbs UPC: 8719076050193 Quick Guide (pdf)Owner's Manual (pdf)Brochure (pdf)

    Read more

    $111.00 $94.35

  • Sale -$16.65 Victron BlueSmart IP67 Charger - 12 VDC - 7AMP - UL Approved [BPC120715106] Victron BlueSmart IP67 Charger - 12 VDC - 7AMP - UL Approved [BPC120715106]

    Victron Energy Victron BlueSmart IP67 Charger - 12 VDC - 7AMP - UL Approved [BPC120715106]

    BlueSmart IP67 Charger - 12 VDC - 7AMPFeatures: Bluetooth Smart enabled The Blue Smart IP67 Charger is the wireless solution to monitor voltage and current, to change settings and to update the charger when new features become available. With Bluetooth, the functionality of the IP67 charger is enhanced and is similar to that of our IP22 and IP65 chargers.  Completely encapsulated: waterproof, shockproof and ignition protected Water, oil or dirt will not damage the Blue Smart IP67 Charger. The casing is made of cast aluminium and the electronics are moulded in resin.  The highest efficiency ever! Setting a new industry standard: with 92% efficiency or better, these chargers waste three to four times less heat. And once the battery is fully charged, power consumption reduces to less than a Watt, some five to ten times better than the industry standard.  Adaptive 5-stage charge algorithm: bulk – absorption – recondition – float – storage The Blue Smart Charger features a microprocessor controlled ‘adaptive’ battery management. The ‘adaptive’ feature will automatically optimize the charging process relative to the way the battery is being used.  Storage Mode: Less maintenance and aging when the battery is not in use The storage mode kicks in whenever the battery has not been subjected to discharge during 24 hours. In the storage mode float voltage is reduced to 2,2 V/cell (13,2 V for a 12 V battery) to minimize gassing and corrosion of the positive plates. Once a week the voltage is raised back to the absorption level to ‘equalize’ the battery. This feature prevents stratification of the electrolyte and sulphation, a major cause of early battery failure.  Also charges Li-ion batteries and LiFePO4 batteries are charged with a simple bulk – absorption – float algorithm.  Protected against overheating Can be used in a hot environment such as a machine room. Output current will reduce as temperature increases up to 60°C, but the charger will not fail.  Two LEDs for status indication Yellow LED: bulk charge (blinking fast), absorption (blinking slow), float (solid), storage (off) Green LED: power on Warranty InfoWARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.Please contact your dealer for any returns, repairs or support issues related to this product. Specifications: Portable: Yes Charging Banks: 1 Charger Output Voltage: 12v Charger Output - Amps: 7a Charger Input - Voltage: 120v Box Dimensions: 4"H x 8"W x 10"L WT: 4.2 lbs UPC: 8719076044703 Quick Guide (pdf)Brochure (pdf)

    Read more

    $111.00 $94.35

  • Victron VE. Bus Smart Dongle [ASS030537010] Victron VE. Bus Smart Dongle [ASS030537010]

    Victron Energy Victron VE. Bus Smart Dongle [ASS030537010]

    VE. Bus Smart DongleThe VE.Bus Smart dongle is two products in one:First of all it is the bluetooth accessory for our range of inverter/chargers: Multis, MultiPlusses, MultiPlus-II, MultiGrid, MultiGrid-II, Quattros, and our series of Phoenix Inverters with a VE.Bus port. When installed, use the VictronConnect app to monitor operation and also operate the system: change the input current limit as well as switch between Off, On and Charger-only modes.Secondly it can work as a Voltage- and Temperature-sense device for the inverter/charger. This works with all models, and is especially useful in combination with the MultiPlus-II, as it does not have on-board terminals for Voltage- and Temperature sense wiringFor monitoring, the device is a great alternative in caravans, smaller yachts and motor homes for which the Color Control GX or Venus GX are a step too far.Warranty InfoWARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.Please contact your dealer for any returns, repairs or support issues related to this product. Quick Guide (pdf)

    Read more

    $93.50

  • Sale -$15.90 Victron Argo Diode Battery Isolator - 160AMP - 2 Batteries [ARG160201020]

    Victron Energy Victron Argo Diode Battery Isolator - 160AMP - 2 Batteries [ARG160201020]

    Argo Diode Battery Isolator - 160AMP - 2 BatteriesDiode battery isolators allow simultaneous charging of two or more batteries from one alternator, without connecting the batteries together. Discharging the accessory battery for example will not result in also discharging the starter battery. The Argo Battery Isolators feature a low voltage drop thanks to the use of Schottky diodes: at low current the voltage drop is approximately 0,3 V and at the rated output approximately 0,45 V. All models are fitted with a compensation diode that can be used to slightly increase the output voltage of the alternator. This compensates for the voltage drop over the diodes in the isolator.Warranty InfoWARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.Please contact your dealer for any returns, repairs or support issues related to this product. Brochure (pdf)

    Read more

    $106.00 $90.10

  • Sale -$15.75 Victron SmartSolar MPPT 100/20 - Up to 48 VDC - UL Approved [SCC110020160R] Victron SmartSolar MPPT 100/20 - Up to 48 VDC - UL Approved [SCC110020160R]

    Victron Energy Victron SmartSolar MPPT 100/20 - Up to 48 VDC - UL Approved [SCC110020160R]

    SmartSolar MPPT 100/20 - Up to 48 VDCA solar charger gathers energy from your solar panels, and stores it in your batteries. Using the latest, fastest technology, SmartSolar maximises this energy-harvest, driving it intelligently to achieve full charge in the shortest possible time. SmartSolar maintains battery health, extending its life.The SmartSolar charge controller will even recharge a severely depleted battery. It can operate with a battery voltage as low as 0 Volts, provided the cells are not permanently sulphated or otherwise damaged.MPPT: Ultra Fast Maximum Power Point TrackingBy constantly monitoring the voltage and current output of your solar (PV) panels, MPPT technology ensures that every drop of available power is rinsed out of your panels, and harvested for storage. The advantage of this is most noticeable when the sky is partially clouded, and light intensity is constantly changing.Remote Monitoring and ControlRemotely control and monitor the extensive features of your SmartSolar MPPT charger with built-in Bluetooth by pairing it with your smartphone or other device via VictronConnect. If your installation is connected to the internet Victron Remote Management Portal (VRM) provides access to the full power of your MPPT, anytime, anywhere; both services are free to use. For remote installations - even when there is no internet connection or phone signal nearby - you may be able to monitor your MPPT by Bluetooth-pairing with a LoRaWAN (long-range wide area network) device, available optionally.Load outputThe intelligent Load output function prevents damage caused by running batteries 'flat'. You can configure the voltage at which SmartSolar disconnects a load - thereby preventing excessive drain on your batteries. And here's the clever bit: SmartSolar will attempt a 100% recharge every day. If it can't - during periods of poor weather - it raises the disconnect voltage, daily, until it achieves success. We call this feature BatteryLife because it maintains the health, and extends the life of your battery.Please contact your dealer for any returns, repairs or support issues related to this product. Quick Guide (pdf)Brochure (pdf)

    Read more

    $105.00 $89.25

  • Sale -$15.45 Victron Phoenix Inverter Control [REC030001210]

    Victron Energy Victron Phoenix Inverter Control [REC030001210]

    Phoenix Inverter ControlThis panel is intended for VE.BUS Phoenix Inverters equipped with a UTP remote monitoring and control socket. It can also be used on a MultiPlus Inverter/Charger when an automatic transfer switch but no charger function is desired. The brightness of the LEDs is automatically reduced during night time. A UTP cable is required to connect the panel to the inverter. Only for models: 12/1200, 12/1600, 12/2000, 12/3000, 12/5000, 24/1200, 24/1600, 24/2000, 24/3000, 24/5000, 48/3000 and 48/5000.Warranty InfoWARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.Please contact your dealer for any returns, repairs or support issues related to this product. Quick Guide (pdf)

    Read more

    $103.00 $87.55

  • Sale -$15.45 Victron BatteryProtect BP-220 - 220AMP - 6-35 VDC [BPR000220400] Victron BatteryProtect BP-220 - 220AMP - 6-35 VDC [BPR000220400]

    Victron Energy Victron BatteryProtect BP-220 - 220AMP - 6-35 VDC [BPR000220400]

    BatteryProtect BP-220 - 220AMP - 6-35 VDCFeatures: The BatteryProtect disconnects the battery from non essential loads before it is completely discharged (which would damage the battery) or before it has insufficient power left to crank the engine.  12/24V auto ranging The BatteryProtect automatically detects system voltage  Programming made easy The BatteryProtect can be set to engage / disengage at several different voltages. The seven segment display will indicate which setting has been chosen.  A special setting for Li-ion batteries In this mode the BatteryProtect can be controlled by the VE.Bus BMS. Note: the BatteryProtect can also be used as a charge interrupter in between a battery charger and a Li-ion battery. See connection diagram in the manual.  Ultra low current consumption This is important in case of Li-ion batteries, especially after low voltage shutdown. Please see our Li-ion battery datasheet and the VE.Bus BMS manual for more information.  Over voltage protection To prevent damage to sensitive loads due to over voltage, the load is disconnected whenever the DC voltage exceeds 16V respectively 32V. Ignition proof No relays but MOSFET switches, and therefore no sparks. Delayed alarm output The alarm output is activated if the battery voltage drops below the preset disconnect level during more than 12 seconds. Starting the engine will therefore not activate the alarm. The alarm output is a short circuit proof open collector output to the negative (minus) rail, max. current 50 mA. The alarm output is typically used to activate a buzzer, LED or relay. Delayed load disconnect and delayed reconnect The load will be disconnected 90 seconds after the alarm has been activated. If the battery voltage increases again to the connect threshold within this time period (after the engine has been started for example), the load will not be disconnected. The load will be reconnected 30 seconds after the battery voltage has increased to more than the preset reconnect voltage. Warranty InfoWARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.Please contact your dealer for any returns, repairs or support issues related to this product. Quick Guide (pdf)Brochure (pdf)

    Read more

    $103.00 $87.55

  • Sale -$15.00 Victron Blue Smart IP65 Charger 12/5(1) 120V - UL Approved [BPC120531104R]

    Victron Energy Victron Blue Smart IP65 Charger 12/5(1) 120V - UL Approved [BPC120531104R]

    Blue Smart IP65 Charger 12/5(1) 120V The Blue Smart IP65 Charger is a professional battery charger with built-in Bluetooth. The Blue Smart IP65 Charger can be used on devices in your workshop and on motor vehicles, such as (classic) cars; motorbikes; boats, and camper-vans.The battery is charged, smartly... to perfect conditionThe seven-step charging algorithm gets the best out of your battery. The charger gives the battery the power it needs, maintains its health, ensures better performance... and longer life.Recovery of deeply-discharged 'dead' batteriesUnlike other brands, the Blue Smart IP65 Charger will attempt to recharge a deeply discharged battery by force-feeding it with a low current. Normal charging will then be resumed as soon as there is sufficient voltage across the battery terminals.Connect the battery with easeThe charger comes with both crocodile clips and M8 eyelets - making it easy to connect to the battery. If you wish, you can leave it permanently connected.Check the status of your battery remotelyThe Blue Smart IP65 is equipped with built-in Bluetooth, so the status of the charger and the battery can be checked on a smartphone, tablet, or laptop. All settings of the charger can be configured with the VictronConnect app.Please contact your dealer for any returns, repairs or support issues related to this product. Quick Guide (pdf)

    Read more

    $100.00 $85.00

  • Sale -$13.80 Victron SmartSolar MPPT Charge Controller - 100V - 15AMP - UL Approved [SCC110015060R] Victron SmartSolar MPPT Charge Controller - 100V - 15AMP - UL Approved [SCC110015060R]

    Victron Energy Victron SmartSolar MPPT Charge Controller - 100V - 15AMP - UL Approved [SCC110015060R]

    SmartSolar MPPT Charge Controller - 100V - 15AMPFeatures: Bluetooth Smart built-in The wireless solution to set-up, monitor, update and synchronise SmartSolar Charge Controllers.  VE.Direct For a wired data connection to a Color Control GX, other GX products, PC or other devices  Ultra-fast Maximum Power Point Tracking (MPPT) Especially in case of a clouded sky, when light intensity is changing continuously, an ultra-fast MPPT controller will improve energy harvest by up to 30% compared to PWM charge controllers and by up to 10% compared to slower MPPT controllers.  Load output Over-discharge of the battery can be prevented by connecting all loads to the load output. The load output will disconnect the load when the battery has been discharged to a pre-set voltage (48V model: interface with a relay). Alternatively, an intelligent battery management algorithm can be chosen: see Battery Life. The load output is short circuit proof.  Battery Life: intelligent battery management When a solar charge controller is not able to recharge the battery to its full capacity within one day, the result is often that the battery will continually be cycled between a ‘partially charged’ state and the ‘end of discharge’ state. This mode of operation (no regular full recharge) will destroy a lead-acid battery within weeks or months. The Battery Life algorithm will monitor the state of charge of the battery and, if needed, day by day slightly increase the load disconnect level (i.e. disconnect the load earlier) until the harvested solar energy is sufficient to recharge the battery to nearly the full 100%. From that point onwards, the load disconnect level will be modulated so that a nearly 100% recharge is achieved about once every week.  Programmable battery charge algorithm See the software section on our website for details  Day/night timing and light dimming option See the software section on our website for details  Internal temperature sensor Compensates absorption and float charge voltage for temperature.  Optional external battery voltage and temperature sensing via Bluetooth A Smart Battery Sense or a BMV-712 Smart Battery Monitor can be used to communicate battery voltage and temperature to one or more SmartSolar Charge Controllers Warranty InfoWARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.Please contact your dealer for any returns, repairs or support issues related to this product. Specifications: Charger Input - Voltage: 18-100v Charger Output - Amps: 15a Charger Output Voltage: 12v/24v Charging Banks: 1 Portable: No Box Dimensions: 3"H x 6"W x 6"L WT: 1.2 lbs UPC: 8719076040811 Quick Guide (pdf)Brochure (pdf)

    Read more

    $92.00 $78.20

  • Victron CYRIX-LI-CHARGE 12/24-120A Intelligent Charge Relay Cyrix LI Charge [CYR010120430]

    Victron Energy Victron CYRIX-LI-CHARGE 12/24-120A Intelligent Charge Relay Cyrix LI Charge [CYR010120430]

    CYRIX-LI-CHARGE 12/24-120A Intelligent Charge Relay Cyrix LI ChargeThe Cyrix Battery Combiner is a microprocessor-controlled heavy duty relay that automatically connects batteries in parallel when one of them has reached a pre-set voltage (indicating that the battery is being charged) and disconnects when the voltage decreases below float level (indicating that one or more batteries are being discharged). Cyrix Battery Combiners are an excellent replacement for diode isolators. The main feature is that there is virtually no voltage loss so that the output voltage of alternators or battery chargers does not need to be increased.Please contact your dealer for any returns, repairs or support issues related to this product. Quick Guide (pdf)

    Read more

    $75.65

  • Sale -$12.60 Victron SmartShunt 300A IP65 Bluetooth Battery Monitor [SHU065130050]

    Victron Energy Victron SmartShunt 300A IP65 Bluetooth Battery Monitor [SHU065130050]

    SmartShunt 300A IP65 Bluetooth Battery MonitorThe SmartShunt is an all-in-one battery monitor, only without a display. Your phone acts as a display. The SmartShunt connects via Bluetooth to the VictronConnect app on your phone (or tablet) and you can conveniently read out all monitored battery parameters, like state of charge, time to go, historical information, and much more.Alternatively, the SmartShunt can be connected and read by a GX device. The connection to the SmartShunt is made via a VE direct cable.The SmartShunt is a good alternative to a BMV battery monitor, especially for systems where battery monitoring is needed but less wiring and clutter are desired. It is equipped with Bluetooth, a VE.Direct port, and a connection that can be used for monitoring a second battery, midpoint monitoring, or a temperature sensor.Please contact your dealer for any returns, repairs or support issues related to this product. Quick Guide (pdf)Owner's Manual (pdf)

    Read more

    $84.00 $71.40

  • Sale -$12.60 Victron SmartShunt 300A [SHU050130050] Victron SmartShunt 300A [SHU050130050]

    Victron Energy Victron SmartShunt 300A [SHU050130050]

    SmartShunt 300AThe SmartShunt is an all-in-one battery monitor, only without a display. Your phone acts as a display. The SmartShunt connects via Bluetooth to the VictronConnect app on your phone (or tablet). You can conveniently read out all monitored battery parameters, like state of charge, time to go, historical information, and much more.Alternatively, the SmartShunt can be connected and read by a GX device. Connection to the SmartShunt is made via a VE.Direct cable.The SmartShunt is a good alternative for a BMV battery monitor, especially for systems where battery monitoring is needed but less wiring and clutter are wanted. The SmartShunt is equipped with Bluetooth, a VE.Direct port and a connection that can be used for: monitoring a second battery, midpoint monitoring or a temperature sensor.Please contact your dealer for any returns, repairs or support issues related to this product. Specifications: Portable: Yes Box Dimensions: 3"H x 4"W x 7"L WT: 0.8 lbs UPC: 8719076065708 Owner's Manual (pdf)Brochure (pdf)

    Read more

    $84.00 $71.40

  • Sale -$12.45 Victron VE. Can to NMEA 2000 Micro-C Male Cable [ASS030520200]

    Victron Energy Victron VE. Can to NMEA 2000 Micro-C Male Cable [ASS030520200]

    VE. Can to NMEA 2000 Micro-C Male CableUse this cable to connect a Victron product with a VE. Can port to a NMEA2000 network.Warranty InfoWARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.Please contact your dealer for any returns, repairs or support issues related to this product. Quick Guide (pdf)

    Read more

    $83.00 $70.55

  • Sale -$12.45 Victron Smart BatteryProtect - 100AMP - 6-35 VDC - Bluetooth Capable [BPR110022000] Victron Smart BatteryProtect - 100AMP - 6-35 VDC - Bluetooth Capable [BPR110022000]

    Victron Energy Victron Smart BatteryProtect - 100AMP - 6-35 VDC - Bluetooth Capable [BPR110022000]

    Smart BatteryProtect - 100AMP - 6-35 VDC - Bluetooth CapableFeatures: Protects the battery against excessive discharge and can be used as a system on/off switch The Smart BatteryProtect disconnects the battery from non-essential loads before it is completely discharged (which would damage the battery) or before it has insufficient power left to crank the engine. The on/off input can be used as a system on/off switch.  12/24V auto ranging The Smart BatteryProtect automatically detects system voltage one time only.  Bluetooth: programming made easy When using Bluetooth to program the Smart BatteryProtect any required engage/disengage levels can be set. Alternatively, one of nine predefined engage/disengage levels can be set with the programming pin (see manual). If required, Bluetooth can be disabled.  A special setting for Li-ion batteries In this mode the BatteryProtect can be controlled by the VE.Bus BMS. Note: the BatteryProtect can also be used as a charge interrupter in between a battery charger and a Li-ion battery. See connection diagram in the manual. Ultra-low current consumption This is important in case of Li-ion batteries, especially after low voltage shutdown. Please see our Li-ion battery datasheet and the VE.Bus BMS manual for more information.  Over voltage protection To prevent damage to sensitive loads due to over voltage, the load is disconnected whenever the DC voltage exceeds 16.3V respectively 32.6V.  Ignition proof No relays but MOSFET switches, and therefore no sparks.  Delayed alarm output The alarm output is activated if the battery voltage drops below the preset disconnect level during more than 12 seconds. Starting the engine will therefore not activate the alarm. The alarm output is a short circuit proof open collector output to the negative (minus) rail, max. current 50 mA. The alarm output is typically used to activate a buzzer, LED or relay.  Delayed load disconnect and delayed reconnect The load will be disconnected 90 seconds after the battery voltage drops below the preset level. If the battery voltage increases again to the connect threshold within this time period (after the engine has been started for example), the load will not be disconnected. The load will be reconnected 30 seconds after the battery voltage has increased to more than the preset reconnect voltage. Warranty InfoWARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.Please contact your dealer for any returns, repairs or support issues related to this product. Quick Guide (pdf)Brochure (pdf)

    Read more

    $83.00 $70.55

  • Victron Interface MK3-USB (VE. BUS to USB) Module [ASS030140000] Victron Interface MK3-USB (VE. BUS to USB) Module [ASS030140000]

    Victron Energy Victron Interface MK3-USB (VE. BUS to USB) Module [ASS030140000]

    Interface MK3-USB (VE. BUS to USB) ModuleThe MK3-USB allows the following products to connect to a computer for configuration and firmware updates:Multi, MultiGrid, MultiPlus, MultiPlus-II, Quattro, Inverter/Charger settings in ECOmulti, EasySolar, EasyPlus, and Inverters with a VE.Bus communication portWarranty InfoWARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.Please contact your dealer for any returns, repairs or support issues related to this product. Quick Guide (pdf)Owner's Manual (pdf)

    Read more

    $68.85

  • Sale -$11.85 Victron SmartSolar MPPT Solar Charge Controller - 75V - 15Amp - UL Approved [SCC075015060R] Victron SmartSolar MPPT Solar Charge Controller - 75V - 15Amp - UL Approved [SCC075015060R]

    Victron Energy Victron SmartSolar MPPT Solar Charge Controller - 75V - 15Amp - UL Approved [SCC075015060R]

    SmartSolar MPPT Charge Controller - 75V - 15AMPFeatures: Bluetooth Smart built-in The wireless solution to set-up, monitor, update and synchronise SmartSolar Charge Controllers.  VE.Direct For a wired data connection to a Color Control GX, other GX products, PC or other devices  Ultra-fast Maximum Power Point Tracking (MPPT) Especially in case of a clouded sky, when light intensity is changing continuously, an ultra-fast MPPT controller will improve energy harvest by up to 30% compared to PWM charge controllers and by up to 10% compared to slower MPPT controllers.  Load output Over-discharge of the battery can be prevented by connecting all loads to the load output. The load output will disconnect the load when the battery has been discharged to a pre-set voltage (48V model: interface with a relay). Alternatively, an intelligent battery management algorithm can be chosen: see Battery Life. The load output is short circuit proof.  Battery Life: intelligent battery management When a solar charge controller is not able to recharge the battery to its full capacity within one day, the result is often that the battery will continually be cycled between a ‘partially charged’ state and the ‘end of discharge’ state. This mode of operation (no regular full recharge) will destroy a lead-acid battery within weeks or months. The Battery Life algorithm will monitor the state of charge of the battery and, if needed, day by day slightly increase the load disconnect level (i.e. disconnect the load earlier) until the harvested solar energy is sufficient to recharge the battery to nearly the full 100%. From that point onwards, the load disconnect level will be modulated so that a nearly 100% recharge is achieved about once every week.  Programmable battery charge algorithm See the software section on our website for details  Day/night timing and light dimming option See the software section on our website for details  Internal temperature sensor Compensates absorption and float charge voltage for temperature.  Optional external battery voltage and temperature sensing via Bluetooth A Smart Battery Sense or a BMV-712 Smart Battery Monitor can be used to communicate battery voltage and temperature to one or more SmartSolar Charge Controllers Warranty InfoWARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.Please contact your dealer for any returns, repairs or support issues related to this product. Specifications: Charger Input - Voltage: 18-75v Charger Output - Amps: 15a Charger Output Voltage: 12v/24v Charging Banks: 1 Portable: No Box Dimensions: 2"H x 6"W x 6"L WT: 1.35 lbs UPC: 8719076040804 Quick Guide (pdf)Brochure (pdf)

    Read more

    $79.00 $67.15

  • Victron Intelligent Load Relay CYRIX-LI-LOAD 12/24V-120A [CYR010120450]

    Victron Energy Victron Intelligent Load Relay CYRIX-LI-LOAD 12/24V-120A [CYR010120450]

    Intelligent Load Relay CYRIX-LI-LOAD 12/24V-120AThe Cyrix Battery Combiner is a microprocessor-controlled heavy duty relay that automatically connects batteries in parallel when one of them has reached a pre-set voltage (indicating that the battery is being charged), and disconnects when the voltage decreases below float level (indicating that one or more batteries are being discharged). Cyrix Battery Combiners are an excellent replacement for diode isolators. The main feature is that there is virtually no voltage loss so that the output voltage of alternators or battery chargers does not need to be increased. Please contact your dealer for any returns, repairs or support issues related to this product. Quick Guide (pdf)

    Read more

    $65.45

  • Sale -$11.25 Victron Orion-Tr Smart 12/24-5A 120W Isolated DC-DC Converter [ORI122410110]

    Victron Energy Victron Orion-Tr Smart 12/24-5A 120W Isolated DC-DC Converter [ORI122410110]

    Orion-Tr Smart 12/24-5A 120W Isolated DC-DC ConverterThe Orion-Tr Smart DC-DC charger is a professional DC to DC adaptive 3-stage charger with built-in Bluetooth.For use in dual battery systems in vehicles or on boats where the (smart) alternator and the start battery are used to charge the service battery. The unit can be monitored and programmed via Bluetooth and can be remotely controlled via a remote on/off switch and has an engine running detection mechanism.The Orion-Tr Smart charger can be used in 12V or 24V systems and is suitable for both lead acid and lithium batteries. Models are available up to 400W and unlimited multiple units can be connected in parallel to increase output power.Suitable for high temperatures up to 55°C with a full rated output up to 40°C. Quick Guide (pdf)

    Read more

    $75.00 $63.75

  • Sale -$11.25 Victron Orion-TR DC-DC Converter - 12 VDC to 12 VDC - 9AMP Isolated [ORI121210110R]

    Victron Energy Victron Orion-TR DC-DC Converter - 12 VDC to 12 VDC - 9AMP Isolated [ORI121210110R]

    Orion-TR 12/12-9A (110W) Isolated DC-DC ConverterRemote On/Off TerminalThe remote on/off terminal eliminates the need for a high current switch in the input wiring. The remote on/off can be operated with a low power switch or for example the engine run/stop switch. All Models Are Short Circuit Proof and Can Be Paralleled to Increase Output CurrentAn unlimited number of units can be connected in parallel.  High Temperature Protected The output current will reduce at high ambient temperatures.  IP43 Protection When installed with the screw terminals oriented downward.  Screw Terminals No special tools are needed for installation.  Input Fuse (not replaceable) On 12 V and 24 V input models only.  Adjustable Output Voltage Not intended for battery charging (consider using an Orion-Tr Smart for battery charging).Specifications: Input Voltage Range: 8-17 V Under Voltage Shut Down: 7 V Under Voltage Restart: 7.5 V Nominal Output Voltage: 12.2 V Output Voltage Adjust Range: 10-15 V Output Voltage Tolerance: +/- 0,2 V Output Noise: 2 mV rms Cont. Output Current at Nominal Output Voltage and 40 Degrees C: 9 A Maximum Output Current (10 S) at Nominal Output Voltage: 12.5 A Short Circuit Output Current: 32 A Cont. Output Power at 25 Degrees C: 110 W Cont. Output Power at 40 Degrees C: 85 W Efficiency: 87 % No Load Input Current (2): < 50 mA  Current Consumption: < 200uA when disabled via its remote port Galvanic Isolation: 200 VDC between input, output, and case Operating Temperature Range: -20 to +55 Degrees C (derate 3 % per °C above 40 °C) Humidity: Max. 95 % non-condensing DC Connection: Screw terminals Maximum Cable Cross-Section: 6 mm² AWG10 Weight: .42 kg (1 lb) Dimensions (H x W x D): 100 x 113 x 47 mm (4.0 x 4.5 x 1.9 inch) Safety Standards: EN 60950 Immunity Standards: EN 61000-6-3, EN 61000-6-1, EN 55014-2 Automotive Directive Standards: ECE R10-5 WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.Please contact your dealer for any returns, repairs or support issues related to this product. Specifications: Charger Input - Voltage: 12v Charger Output - Amps: 9a Charger Output Voltage: 12v Box Dimensions: 3"H x 6"W x 9"L WT: 1.05 lbs UPC: 8719076016878 Quick Guide (pdf)Owner's Manual (pdf)Brochure (pdf)

    Read more

    $75.00 $63.75

  • Sale -$10.95 Victron SmartSolar MPPT Solar Charge Controller - 75V - 10Amp - UL Approved [SCC075010060R] Victron SmartSolar MPPT Solar Charge Controller - 75V - 10Amp - UL Approved [SCC075010060R]

    Victron Energy Victron SmartSolar MPPT Solar Charge Controller - 75V - 10Amp - UL Approved [SCC075010060R]

    SmartSolar MPPT Charge Controller - 75V - 10AMPFeatures: Bluetooth Smart built-in The wireless solution to set-up, monitor, update and synchronise SmartSolar Charge Controllers.  VE.Direct For a wired data connection to a Color Control GX, other GX products, PC or other devices  Ultra-fast Maximum Power Point Tracking (MPPT) Especially in case of a clouded sky, when light intensity is changing continuously, an ultra-fast MPPT controller will improve energy harvest by up to 30% compared to PWM charge controllers and by up to 10% compared to slower MPPT controllers.  Load output Over-discharge of the battery can be prevented by connecting all loads to the load output. The load output will disconnect the load when the battery has been discharged to a pre-set voltage (48V model: interface with a relay). Alternatively, an intelligent battery management algorithm can be chosen: see Battery Life. The load output is short circuit proof.  Battery Life: intelligent battery management When a solar charge controller is not able to recharge the battery to its full capacity within one day, the result is often that the battery will continually be cycled between a ‘partially charged’ state and the ‘end of discharge’ state. This mode of operation (no regular full recharge) will destroy a lead-acid battery within weeks or months. The Battery Life algorithm will monitor the state of charge of the battery and, if needed, day by day slightly increase the load disconnect level (i.e. disconnect the load earlier) until the harvested solar energy is sufficient to recharge the battery to nearly the full 100%. From that point onwards, the load disconnect level will be modulated so that a nearly 100% recharge is achieved about once every week.  Programmable battery charge algorithm See the software section on our website for details  Day/night timing and light dimming option See the software section on our website for details  Internal temperature sensor Compensates absorption and float charge voltage for temperature.  Optional external battery voltage and temperature sensing via Bluetooth A Smart Battery Sense or a BMV-712 Smart Battery Monitor can be used to communicate battery voltage and temperature to one or more SmartSolar Charge Controllers Warranty InfoWARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.Please contact your dealer for any returns, repairs or support issues related to this product. Specifications: Charger Input - Voltage: 18-75v Charger Output - Amps: 10a Charger Output Voltage: 12v/24v Charging Banks: 1 Portable: No Box Dimensions: 2"H x 6"W x 6"L WT: 0.85 lbs UPC: 8719076040798 Quick Guide (pdf)Brochure (pdf)

    Read more

    $73.00 $62.05

  • Sale -$10.80 Victron BlueSolar MPPT Charge Controller - 100V - 15AMP - UL Approved [SCC010015200R]

    Victron Energy Victron BlueSolar MPPT Charge Controller - 100V - 15AMP - UL Approved [SCC010015200R]

    BlueSolar MPPT Charge Controller - 100V - 15AMPFeatures: Ultra-fast Maximum Power Point Tracking (MPPT) Especially in case of a clouded sky, when light intensity is changing continuously, an ultra-fast MPPT controller will improve energy harvest by up to 30% compared to PWM charge controllers and by up to 10% compared to slower MPPT controllers.  Load output Over-discharge of the battery can be prevented by connecting all loads to the load output. The load output will disconnect the load when the battery has been discharged to a pre-set voltage. Alternatively, an intelligent battery management algorithm can be chosen: see Battery Life. The load output is short circuit proof. Some loads (especially inverters) can best be connected directly to the battery, and the inverter remote control connected to the load output. A special interface cable may be needed, please see the manual.  Battery Life: intelligent battery management When a solar charge controller is not able to recharge the battery to its full capacity within one day, the result is often that the battery will continually be cycled between a ‘partially charged’ state and the ‘end of discharge’ state. This mode of operation (no regular full recharge) will destroy a lead-acid battery within weeks or months. The Battery Life algorithm will monitor the state of charge of the battery and, if needed, day by day slightly increase the load disconnect level (i.e. disconnect the load earlier) until the harvested solar energy is sufficient to recharge the battery to nearly the full 100%. From that point onwards the load disconnect level will be modulated so that a nearly 100% recharge is achieved about once every week.  Programmable battery charge algorithm See the software section on our website for details  Day/night timing and light dimming option See the software section on our website for details  Programming, real-time data and history display options - Color Control GX or other GX devices: see the Venus documents on our website. - A smartphone or other Bluetooth-enabled device: VE.Direct Bluetooth Smart dongle needed Warranty InfoWARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.Please contact your dealer for any returns, repairs or support issues related to this product. Specifications: Charger Input - Voltage: 18-75v Charger Output - Amps: 15a Charger Output Voltage: 12v/24v Charging Banks: 1 Portable: No Box Dimensions: 3"H x 6"W x 6"L WT: 1.2 lbs UPC: 8719076025337 Quick Guide (pdf)Brochure (pdf)

    Read more

    $72.00 $61.20

  • Victron Interface MK3-USB-C - VE.Bus to USB-C Adapter [ASS030140030]

    Victron Energy Victron Interface MK3-USB-C - VE.Bus to USB-C Adapter [ASS030140030]

    Interface MK3-USB-C - VE.Bus to USB-C AdapterThe MK3-USB-C allows the following products to connect to a computer for configuration and firmware updates: Multi MultiGrid MultiPlus MultiPlus-II Quattro VE.Bus BMS V2 Inverter/Charger settings in ECOmulti EasySolar EasyPlus Inverters with a VE.Bus communication port Please contact your dealer for any returns, repairs or support issues related to this product. Specifications: Type: Adapters Box Dimensions: 2"H x 4"W x 5"L WT: 0.25 lbs UPC: 8719076057994

    Read more

    $59.50

  • Victron Battery Alarm GX [BPA000100010R]

    Victron Energy Victron Battery Alarm GX [BPA000100010R]

    Battery Alarm GXThe Battery Alarm is a small and low-cost alarm panel that monitors your battery bank. It features both audible and visual alarms, as well as a potential free contact with normally open and normally closed contacts. Alarm thresholds and hysteresis are programmable by DIP switches.Warranty InfoWARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.Please contact your dealer for any returns, repairs or support issues related to this product. Quick Guide (pdf)

    Read more

    $57.80

  • Sale -$10.05 Victron Busbar 250A 4P Cover 4X 5/16" Terminals [VBB125040010]

    Victron Energy Victron Busbar 250A 4P Cover 4X 5/16" Terminals [VBB125040010]

    Busbar 250A 4P & Cover 4X 5/16" TerminalsBusbars are used for high current distribution and at the same time they provide connections for batteries and/or DC equipment.We offer a number of busbars with different current ratings, and a different number of connection terminals. Each busbar is fitted out with a removable protective cover.Please contact your dealer for any returns, repairs or support issues related to this product. Quick Guide (pdf)

    Read more

    $67.00 $56.95

  • Victron BlueSolar PWM Charge Controller (DUO) LCD USB Charge Control - 12/24VDC - 20A [SCC010020060] Victron BlueSolar PWM Charge Controller (DUO) LCD USB Charge Control - 12/24VDC - 20A [SCC010020060]

    Victron Energy Victron BlueSolar PWM Charge Controller (DUO) LCD USB Charge Control - 12/24VDC - 20A [SCC010020060]

    BlueSolar PWM Charge Controller (DUO) LCD & USB Charge Control - 12/24VDC - 20AFeatures: Liquid Crystal Display Two 5 Volt USB outputs Lighting control function, fully programmable   Three-stage battery charging (bulk, absorption, float), fully programmable Load output with low voltage and manual disconnect (programmable) Load output protected against overload and short circuit Protected against reverse polarity connection of the solar panels and/or battery Charges two separate batteries Programmable charge current ratio External Temperature sensor Please contact your dealer for any returns, repairs or support issues related to this product. Quick Guide (pdf)Brochure (pdf)

    Read more

    $56.10

  • Victron 325A/80V CNN Fuse f/Lynx Shunt [CIP140325000]

    Victron Energy Victron 325A/80V CNN Fuse f/Lynx Shunt [CIP140325000]

    325A/80V CNN Fuse for Lynx ShuntVictron's 325A/80V fuse is designed to fit the Lynx Shunt VE. CanSpecifications: Rated Amperage: 325A Rated Voltage: 80V Terminal Size: 10mm Please contact your dealer for any returns, repairs or support issues related to this product. Specifications: Amperage: 325a Type: Fuses Box Dimensions: 1"H x 4"W x 6"L WT: 0.1 lbs

    Read more

    $55.25

  • Sale -$9.45 Victron Smart BatteryProtect - 65AMP - 6-35 VDC - Bluetooth Capable [BPR065022000] Victron Smart BatteryProtect - 65AMP - 6-35 VDC - Bluetooth Capable [BPR065022000]

    Victron Energy Victron Smart BatteryProtect - 65AMP - 6-35 VDC - Bluetooth Capable [BPR065022000]

    Smart BatteryProtect - 65AMP - 6-35 VDC - Bluetooth CapableFeatures: Protects the battery against excessive discharge and can be used as a system on/off switch The Smart BatteryProtect disconnects the battery from non-essential loads before it is completely discharged (which would damage the battery) or before it has insufficient power left to crank the engine. The on/off input can be used as a system on/off switch.  12/24V auto ranging The Smart BatteryProtect automatically detects system voltage one time only.  Bluetooth: programming made easy When using Bluetooth to program the Smart BatteryProtect any required engage/disengage levels can be set. Alternatively, one of nine predefined engage/disengage levels can be set with the programming pin (see manual). If required, Bluetooth can be disabled.  A special setting for Li-ion batteries In this mode the BatteryProtect can be controlled by the VE.Bus BMS. Note: the BatteryProtect can also be used as a charge interrupter in between a battery charger and a Li-ion battery. See connection diagram in the manual. Ultra-low current consumption This is important in case of Li-ion batteries, especially after low voltage shutdown. Please see our Li-ion battery datasheet and the VE.Bus BMS manual for more information.  Over voltage protection To prevent damage to sensitive loads due to over voltage, the load is disconnected whenever the DC voltage exceeds 16.3V respectively 32.6V.  Ignition proof No relays but MOSFET switches, and therefore no sparks.  Delayed alarm output The alarm output is activated if the battery voltage drops below the preset disconnect level during more than 12 seconds. Starting the engine will therefore not activate the alarm. The alarm output is a short circuit proof open collector output to the negative (minus) rail, max. current 50 mA. The alarm output is typically used to activate a buzzer, LED or relay.  Delayed load disconnect and delayed reconnect The load will be disconnected 90 seconds after the battery voltage drops below the preset level. If the battery voltage increases again to the connect threshold within this time period (after the engine has been started for example), the load will not be disconnected. The load will be reconnected 30 seconds after the battery voltage has increased to more than the preset reconnect voltage. Warranty InfoWARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.Please contact your dealer for any returns, repairs or support issues related to this product. Quick Guide (pdf)Brochure (pdf)

    Read more

    $63.00 $53.55

  • Sale -$9.45 Victron BatteryProtect BP-100 - 100AMP - 6-35 VDC [BPR000100400] Victron BatteryProtect BP-100 - 100AMP - 6-35 VDC [BPR000100400]

    Victron Energy Victron BatteryProtect BP-100 - 100AMP - 6-35 VDC [BPR000100400]

    BatteryProtect BP-100 - 100AMP - 6-35 VDCFeatures: The BatteryProtect disconnects the battery from non essential loads before it is completely discharged (which would damage the battery) or before it has insufficient power left to crank the engine.  12/24V auto ranging The BatteryProtect automatically detects system voltage  Programming made easy The BatteryProtect can be set to engage / disengage at several different voltages. The seven segment display will indicate which setting has been chosen.  A special setting for Li-ion batteries In this mode the BatteryProtect can be controlled by the VE.Bus BMS. Note: the BatteryProtect can also be used as a charge interrupter in between a battery charger and a Li-ion battery. See connection diagram in the manual.  Ultra low current consumption This is important in case of Li-ion batteries, especially after low voltage shutdown. Please see our Li-ion battery datasheet and the VE.Bus BMS manual for more information.  Over voltage protection To prevent damage to sensitive loads due to over voltage, the load is disconnected whenever the DC voltage exceeds 16V respectively 32V. Ignition proof No relays but MOSFET switches, and therefore no sparks. Delayed alarm output The alarm output is activated if the battery voltage drops below the preset disconnect level during more than 12 seconds. Starting the engine will therefore not activate the alarm. The alarm output is a short circuit proof open collector output to the negative (minus) rail, max. current 50 mA. The alarm output is typically used to activate a buzzer, LED or relay. Delayed load disconnect and delayed reconnect The load will be disconnected 90 seconds after the alarm has been activated. If the battery voltage increases again to the connect threshold within this time period (after the engine has been started for example), the load will not be disconnected. The load will be reconnected 30 seconds after the battery voltage has increased to more than the preset reconnect voltage. Warranty InfoWARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.Please contact your dealer for any returns, repairs or support issues related to this product. Quick Guide (pdf)Brochure (pdf)

    Read more

    $63.00 $53.55

  • Sale -$9.30 Victron Blue Smart IP65 Charger - 6V/12V - 1.1A - 120V - 1-15P [BPC120134124R]

    Victron Energy Victron Blue Smart IP65 Charger - 6V/12V - 1.1A - 120V - 1-15P [BPC120134124R]

    Blue Smart IP65 Charger - 6V/12V - 1.1A - 120V - 1-15PThe Blue Smart IP65 Charger is the new professional battery charger with built-in Bluetooth. The Blue Smart IP65 Charger can be used on devices in the workshop and motor vehicles, such as (classic) cars; motorbikes; boats, and camper vans. The battery is charged, smartly... to the perfect conditionThe seven-step charging algorithm gets the best out of a battery. The charger gives the battery the power it needs, maintains its health, and ensures better performance... and longer life.Recovery of deeply-discharged 'dead' batteriesUnlike other brands, the Blue Smart IP65 Charger will attempt to recharge a deeply-discharged battery by force-feeding it with a low current. Regular charging will then be resumed as soon as sufficient voltage is across the battery terminals.Connect the battery with easeThe charger comes with both crocodile clips and M8 eyelets - making it easy to connect to the battery. If users wish, it can be left permanently connected.Check the status of your battery remotelyThe Blue Smart IP65 is equipped with built-in Bluetooth, so the status of the charger and the battery can be checked on a smartphone, tablet, or laptop. All settings of the charger can be configured with the VictronConnect app.Specifications: Input Voltage & Frequency Range: 100 - 250VAC | 45 - 65Hz  Efficiency: 82% Standby Power Consumption: <0,5 W  Minimum Battery Voltage: Starts charging from down to 0 V Charge voltage 'absorption': Normal: 7,2 V | 14,4 V / High: 7,35 V | 14,7 V / Li-ion: 7,1 V | 14,2 V Charge Voltage 'float': Normal: 6,9 V | 13,8 V / High: 6,9 V | 13,8 V / Li-ion: Disabled Charge Voltage 'storage': Normal: 6,6 V | 13,2 V / High: 6,6 V | 13,2 V / Li-ion: 6,75 V | 13,5 V Charge Current: 1.1 A  Low-Current Mode: 0,5A  Temperature Compensation (lead-acid batteries only): 8 mV/°C | 16 mV/°C  Power Supply Mode: Yes Back Current Drain: 0,1 Ah/month (140uA)  Protection: Reverse polarity, Output short circuit, Over-temperature Operating Temp. Range: -30 to +50°C (full rated output up to 30°C) Humidity (non-condensing): Max 95% Charge Algorithm: 7-stage adaptive Bluetooth: 4dBm, 2402–2480 MHz Enclosure Specifications: Battery-Connection: Black and red cable of 1,5 meter 230V AC connection: 1.5m cable with CEE 7/16 or AS/NZS 3112 plug Protection Category: IP65 (splash and dust proof) Weight: 0,4 kg Dimensions: 38 x 64 x 153 mm Standards: Safety: EN 60335-1, EN 60335-2-29 Emission; EN 55014-1, EN 61000-6-3, EN 61000-3-2 Immunity: EN 55014-2, EN 61000-6-1, EN 61000-6-2, EN 61000-3-3 Please contact your dealer for any returns, repairs or support issues related to this product. Quick Guide (pdf)Owner's Manual (pdf)Brochure (pdf)

    Read more

    $62.00 $52.70

  • Victron MPPT Control for MPPT Solar Charge Controllers [SCC900500000] Victron MPPT Control for MPPT Solar Charge Controllers [SCC900500000]

    Victron Energy Victron MPPT Control for MPPT Solar Charge Controllers [SCC900500000]

    MPPT Control w/ VE Direct portMPPT Control lets you see the status and setup all MPPTs that use a VE.Direct communications port. The new MPPT Control is mounted in the familiar BMV-700 series housing, maintaining a consistent and professional look to your panels and systems monitoring equipment.Features: View live status information, including solar watts, battery voltage, charge current, load current and more. View Historical information View All Time values View 30 Day Historical values Complete MPPT setup Warranty InfoPlease contact your dealer for any returns, repairs or support issues related to this product. Quick Guide (pdf)Brochure (pdf)

    Read more

    $51.00

  • Sale -$8.85 Victron Argodiode Battery Isolator 80-2AC - 2 Batteries - 80A [ARG080201000]

    Victron Energy Victron Argodiode Battery Isolator 80-2AC - 2 Batteries - 80A [ARG080201000]

    Argodiode Battery Isolator 80-2AC - 2 Batteries - 80AArgodiode Battery Isolators allow simultaneous charging of two or more batteries from one alternator, without connecting the batteries. Discharging the accessory battery for example will not result in also discharging the starter battery. Low voltage drop due to the use of high-efficiency Schottky diodes.The Argo Battery Isolators feature a low voltage drop thanks to the use of Schottky diodes: at low current, the voltage drop is approximately 0,3 V, and at the rated output of approximately 0,45 V. All models are fitted with a compensation diode that can be used to slightly increase the output voltage of the alternator. This compensates for the voltage drop over the diodes in the isolator. Simply inserting the isolator in the cabling between the alternator and the batteries will slightly reduce charge voltage. The result can be that batteries are not charged to the full 100% and age prematurely. Alternator energize input Some alternators need DC voltage on the B+ output to start charging. Obviously, DC will be present when the alternator is directly connected to a battery. Inserting a Diode or FET splitter will however prevent any return voltage/current from the batteries to the B+, and the alternator will not start. The new ‘AC’ diode isolators feature a special current limited energize input that will power the B+ when the engine run/stop switch is closed.Please contact your dealer for any returns, repairs or support issues related to this product.

    Read more

    $59.00 $50.15

  • Sale -$8.85 Victron Busbar 250A 2P w/12 Screws Cover [VBB125021220]

    Victron Energy Victron Busbar 250A 2P w/12 Screws Cover [VBB125021220]

    Busbar 250A 2P with 12 Screws & CoverBusbars are used for high current distribution and at the same time they provide connections for batteries and/or DC equipment.We offer a number of busbars with different current ratings, and a different number of connection terminals. Each busbar is fitted out with a removable protective cover. Quick Guide (pdf)

    Read more

    $59.00 $50.15

  • Sale -$8.85 Victron BlueSolar MPPT Charge Controller - 75V - 15AMP - UL Approved [SCC010015050R]

    Victron Energy Victron BlueSolar MPPT Charge Controller - 75V - 15AMP - UL Approved [SCC010015050R]

    BlueSolar MPPT Charge Controller - 75V - 15AMPFeatures: Ultra-fast Maximum Power Point Tracking (MPPT) Especially in case of a clouded sky, when light intensity is changing continuously, an ultra-fast MPPT controller will improve energy harvest by up to 30% compared to PWM charge controllers and by up to 10% compared to slower MPPT controllers.  Load output Over-discharge of the battery can be prevented by connecting all loads to the load output. The load output will disconnect the load when the battery has been discharged to a pre-set voltage. Alternatively, an intelligent battery management algorithm can be chosen: see Battery Life. The load output is short circuit proof. Some loads (especially inverters) can best be connected directly to the battery, and the inverter remote control connected to the load output. A special interface cable may be needed, please see the manual.  Battery Life: intelligent battery management When a solar charge controller is not able to recharge the battery to its full capacity within one day, the result is often that the battery will continually be cycled between a ‘partially charged’ state and the ‘end of discharge’ state. This mode of operation (no regular full recharge) will destroy a lead-acid battery within weeks or months. The Battery Life algorithm will monitor the state of charge of the battery and, if needed, day by day slightly increase the load disconnect level (i.e. disconnect the load earlier) until the harvested solar energy is sufficient to recharge the battery to nearly the full 100%. From that point onwards the load disconnect level will be modulated so that a nearly 100% recharge is achieved about once every week.  Programmable battery charge algorithm See the software section on our website for details  Day/night timing and light dimming option See the software section on our website for details  Programming, real-time data and history display options - Color Control GX or other GX devices: see the Venus documents on our website. - A smartphone or other Bluetooth-enabled device: VE.Direct Bluetooth Smart dongle needed Warranty InfoWARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.Please contact your dealer for any returns, repairs or support issues related to this product. Specifications: Charger Input - Voltage: 18-75v Charger Output - Amps: 15a Charger Output Voltage: 12v/24v Charging Banks: 1 Portable: No Box Dimensions: 2"H x 6"W x 6"L WT: 1.3 lbs UPC: 8719076025320 Quick Guide (pdf)Brochure (pdf)

    Read more

    $59.00 $50.15

  • Victron CYRIX-CT 12/24V-120A Intelligent Battery Combiner [CYR010120011R]

    Victron Energy Victron CYRIX-CT 12/24V-120A Intelligent Battery Combiner [CYR010120011R]

    CYRIX-CT 12/24V-120A Intelligent Battery CombinerThe Cyrix Battery Combiner is a microprocessor controlled heavy duty relay that automatically connects batteries in parallel when one of them has reached a pre-set voltage (indicating that the battery is being charged) and disconnects when the voltage decreases below float level (indicating that one or more batteries are being discharged). Cyrix Battery Combiners are an excellent replacement for diode isolators. The main feature is that there is virtually no voltage loss so the output voltage of alternators or battery chargers does not need to be increased.Please contact your dealer for any returns, repairs or support issues related to this product. Quick Guide (pdf)Owner's Manual (pdf)Brochure (pdf)

    Read more

    $49.30

  • Victron SmallBMS f/Smart LiFePO4 Batteries w/M8 [BMS400100000] Victron SmallBMS f/Smart LiFePO4 Batteries w/M8 [BMS400100000]

    Victron Energy Victron SmallBMS f/Smart LiFePO4 Batteries w/M8 [BMS400100000]

    SmallBMS for Smart LiFePO4 Batteries with M8A simple and low-cost alternative to the VE.Bus BMS. The smallBMS can replace the VE.Bus BMS in several applications. It is however not suitable for use with VE.Bus MultiPlus and Quattro inverter/chargers: it has no VE.Bus interface.The smallBMS is intended for use with Victron Smart LiFePo4 batteries with M8 circular connectors. The smallBMS has three outputs, similar to the VE.Bus BMS. Load Disconnect output The Load output is normally high and becomes free-floating in case of the cell under voltage (default 2,8V/cell, adjustable on the battery between 2,6V and 2,8V per cell). Maximum current: 1A. The Load output is not short-circuit protected.The Load output can be used to control: A high current relay or contactor. The remote on/off the input of a Battery Protect, inverter or DC-DC converter, or other loads. Pre-alarm outputThe pre-alarm output is normally free-floating and becomes high in case of the imminent cell under voltage (default 3,1V/cell, adjustable on the battery between 2,85V and 3,15V per cell). Maximum current: 1A (not short circuit protected).The minimum delay between pre-alarm and load disconnect is 30 seconds.Charge disconnect outputThe Charger output is normally high and becomes free-floating in case of imminent cell overvoltage or over-temperature. Maximum current: 10mA. The Charger output is not suitable to power an inductive load such as a relay coil. The Charger output can be used to control: The remote on/off of a charger A Cyrix-Li-Charge relay A Cyrix-Li-ct Battery Combiner System on/off inputThe system on/off input controls both outputs. When off, both outputs will be free floating so that loads and chargers are turned off. The System on/off consists of two terminals: Remote L and Remote H. A remote on/off switch or relay contact can be connected between L and H. Alternatively, terminal H can be switched to battery plus, or terminal L can be switched to battery minus.Protects 12V, 24V and 48V systemsOperating voltage range: 8 to 70V DC.LED indicators: Load ON (blue): Load output high (cell voltage >2.8V, adjustable on the battery). Temp or OVP (red): Charger output free floating (due to cell over temperature (>50°C), cell under temperature (<5 °C) or cell over voltage). Please contact your dealer for any returns, repairs or support issues related to this product. Quick Guide (pdf)Brochure (pdf)

    Read more

    $49.30

  • Sale -$8.55 Victron Battery Balancer [BBA000100100] Victron Battery Balancer [BBA000100100]

    Victron Energy Victron Battery Balancer [BBA000100100]

    Battery BalancerThe Battery Balancer equalizes the state of charge of two series connected 12V batteries, or of several parallel strings of series connected batteries. When the charge voltage of a 24V battery system increases to more than 27V, the Battery Balancer will turn on and compare the voltage over the two series connected batteries. The Battery Balancer will draw a current of up to 1A from the battery (or parallel connected batteries) with the highest voltage. The resulting charge current differential will ensure that all batteries will converge to the same state of charge.If needed, several balancers can be paralleled. A 48V battery bank can be balanced with three Battery Balancers.WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.Please contact your dealer for any returns, repairs or support issues related to this product. Quick Guide (pdf)Brochure (pdf)

    Read more

    $57.00 $48.45

  • Sale -$7.95 Victron Orion IP67 DC-DC Converter - 24/12 VDC - 20AMP - 240W [ORI241220260]

    Victron Energy Victron Orion IP67 DC-DC Converter - 24/12 VDC - 20AMP - 240W [ORI241220260]

    Orion IP67 DC-DC Converter - 24/12 VDC - 20AMP - 240WFeatures: Completely encapsulated: waterproof, shockproof and ignition protected Water, oil or dirt will not damage the Orion IP67 DC-DC Converter. The casing is made of cast aluminium and the electronics are moulded in resin.  Extra-long input and output cables Thanks to the cables of 1.8 meters in length, intermediate cable interconnections to increase length even more will in most cases not be needed. This is an important reliability increasing feature in an area were IP67 protection grade is needed.  Wide input voltage range With 15 to 40 Volts input range, a stable output is ensured during surges or sags due to other equipment connected to same battery.  Protected against overheating It can be used in a hot environment such as a machine room. Warranty InfoPlease contact your dealer for any returns, repairs or support issues related to this product. Quick Guide (pdf)Brochure (pdf)

    Read more

    $53.00 $45.05

  • Victron Busbar to Connect 6 Modular Holders [CIP100400070]

    Victron Energy Victron Busbar to Connect 6 Modular Holders [CIP100400070]

    Busbar to Connect 6 Modular HoldersFeatures: Six position high current bus bar (1500 A) With two M10 input connections. Input current up to 2000 A. Recommended to parallel multiple high power Multi or Quattro inverter/chargers Warranty InfoWARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.Please contact your dealer for any returns, repairs or support issues related to this product. Quick Guide (pdf)

    Read more

    $45.05

  • Sale -$7.95 Victron BlueSolar MPPT Charge Controller - 75V - 10AMP - UL Approved [SCC010010050R]

    Victron Energy Victron BlueSolar MPPT Charge Controller - 75V - 10AMP - UL Approved [SCC010010050R]

    BlueSolar MPPT Charge Controller - 75V - 10AMPFeatures: Ultra-fast Maximum Power Point Tracking (MPPT) Especially in case of a clouded sky, when light intensity is changing continuously, an ultra-fast MPPT controller will improve energy harvest by up to 30% compared to PWM charge controllers and by up to 10% compared to slower MPPT controllers.  Load output Over-discharge of the battery can be prevented by connecting all loads to the load output. The load output will disconnect the load when the battery has been discharged to a pre-set voltage. Alternatively, an intelligent battery management algorithm can be chosen: see Battery Life. The load output is short circuit proof. Some loads (especially inverters) can best be connected directly to the battery, and the inverter remote control connected to the load output. A special interface cable may be needed, please see the manual.  Battery Life: intelligent battery management When a solar charge controller is not able to recharge the battery to its full capacity within one day, the result is often that the battery will continually be cycled between a ‘partially charged’ state and the ‘end of discharge’ state. This mode of operation (no regular full recharge) will destroy a lead-acid battery within weeks or months. The Battery Life algorithm will monitor the state of charge of the battery and, if needed, day by day slightly increase the load disconnect level (i.e. disconnect the load earlier) until the harvested solar energy is sufficient to recharge the battery to nearly the full 100%. From that point onwards the load disconnect level will be modulated so that a nearly 100% recharge is achieved about once every week.  Programmable battery charge algorithm See the software section on our website for details  Day/night timing and light dimming option See the software section on our website for details  Programming, real-time data and history display options - Color Control GX or other GX devices: see the Venus documents on our website. - A smartphone or other Bluetooth-enabled device: VE.Direct Bluetooth Smart dongle needed Warranty InfoWARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.Please contact your dealer for any returns, repairs or support issues related to this product. Specifications: Charger Input - Voltage: 18-75v Charger Output - Amps: 10a Charger Output Voltage: 12v/24v Charging Banks: 1 Portable: No Box Dimensions: 2"H x 6"W x 7"L WT: 0.8 lbs UPC: 8719076025306 Quick Guide (pdf)Brochure (pdf)

    Read more

    $53.00 $45.05

  • Sale -$7.95 Victron Argo Diode Battery Combiner - 80AMP - 2 Batteries [BCD000802000] Victron Argo Diode Battery Combiner - 80AMP - 2 Batteries [BCD000802000]

    Victron Energy Victron Argo Diode Battery Combiner - 80AMP - 2 Batteries [BCD000802000]

    Argo Diode Battery Combiner - 80AMP - 2 BatteriesDiode Battery Combiners are used to guarantee continuous DC power to mission critical equipment, such as an electronic engine control system. With a Diode Battery Combiner two or more DC power sources can be used in parallel to supply the mission critical load. Failure of one source will not interrupt power to the critical load.Warranty InfoWARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.Please contact your dealer for any returns, repairs or support issues related to this product. Quick Guide (pdf)Brochure (pdf)

    Read more

    $53.00 $45.05

  • Sale -$7.65 Victron Busbar 250A 2P w/6 Screws Cover [VBB125020620]

    Victron Energy Victron Busbar 250A 2P w/6 Screws Cover [VBB125020620]

    Busbar 250A 2P with 6 Screws & CoverBusbars are used for high current distribution and at the same time they provide connections for batteries and/or DC equipment.We offer a number of busbars with different current ratings, and a different number of connection terminals. Each busbar is fitted out with a removable protective cover. Quick Guide (pdf)

    Read more

    $51.00 $43.35

  • Victron M8 Circular Connector 3-Pole BMS BTV Extension Cables - Pair - 5M [ASS030560500]

    Victron Energy Victron M8 Circular Connector 3-Pole BMS BTV Extension Cables - Pair - 5M [ASS030560500]

    M8 Circular Connector 3-Pole BMS BTV Extension Cables - Pair - 5MFeatures: 5-meter cable Extends the data cables that run from a 12.8 Volt Lithium-Ion battery to the BMS Please contact your dealer for any returns, repairs or support issues related to this product. Quick Guide (pdf)

    Read more

    $42.50

  • Sale -$7.20 Victron Carry Case f/IP65 Charger 12/25 24/13 - Fits Charger Accessories [BPC940100200] Victron Carry Case f/IP65 Charger 12/25 24/13 - Fits Charger Accessories [BPC940100200]

    Victron Energy Victron Carry Case f/IP65 Charger 12/25 24/13 - Fits Charger Accessories [BPC940100200]

    Carry Case for IP65 Charger 12/25 & 24/13 - Fits Charger & AccessoriesSmart and professional, this new snap-close carry case provides protective stowage and easy transport for Victron’s Blue Smart IP65 charger and its accessories.Compartments accommodate the charger, its input/output cables, and the battery-clamp/eyelet cable options.Specifications:Size: 345 x 520 x 130mm(Charger and accessories not included) Quick Guide (pdf)Brochure (pdf)

    Read more

    $48.00 $40.80

  • Sale -$7.05 Victron MagCode Power Port f/Blue Smart IP65 Charger - 12V - 15 Amp Max (Requires Power Clip) [BPC900520014]

    Victron Energy Victron MagCode Power Port f/Blue Smart IP65 Charger - 12V - 15 Amp Max (Requires Power Clip) [BPC900520014]

    MagCode Power Port for Blue Smart IP65 Charger - 12V - 15 Amp Max (Requires Power Clip)MagCode Power Port is a magnetic connector for Victon's Blue Smart IP65 Chargers.Specifications: Volt: 12V Max Amp: 15 *Requires Victon’s MagCode Power ClipPlease contact your dealer for any returns, repairs or support issues related to this product. Quick Guide (pdf)

    Read more

    $47.00 $39.95

  • Victron MagCode Power Clip f/Blue Smart IP65 Charger - 12V - 15 Amp Max (Requires Power Port) [BPC900500014]

    Victron Energy Victron MagCode Power Clip f/Blue Smart IP65 Charger - 12V - 15 Amp Max (Requires Power Port) [BPC900500014]

    MagCode Power Clip for Blue Smart IP65 Charger - 12V - 15 Amp Max (Requires Power Port)MagCode Power Clip is a connection cable for the Victon's Blue Smart IP65 Chargers.Features: 12V 15 amp max *Requires Victon’s MagCode Power PortPlease contact your dealer for any returns, repairs or support issues related to this product. Quick Guide (pdf)

    Read more

    $39.95

  • Sale -$7.05 Victron VE. Direct to Bluetooth Smart Dongle w/ 1.5M Cable [ASS030536011]

    Victron Energy Victron VE. Direct to Bluetooth Smart Dongle w/ 1.5M Cable [ASS030536011]

    VE. Direct Bluetooth Smart DongleUsing the VE.Direct to Bluetooth Smart dongle you can display your BMV or MPPT information on iOS and Android devices, using the VictronConnect app. View information wirelessly such as battery status and solar panel power, plus other useful data. The dongle is able to read data from all products with a VE.Direct port, such as the BMV-70x series battery monitors, Phoenix Inverters with VE.Direct port, MPPT Solar Charge Controllers.Warranty InfoWARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.Please contact your dealer for any returns, repairs or support issues related to this product. Quick Guide (pdf)Owner's Manual (pdf)

    Read more

    $47.00 $39.95

  • Sale -$6.90 Victron Argodiode Battery Isolator 80-2SC - 2 Batteries - 80A [ARG080202000]

    Victron Energy Victron Argodiode Battery Isolator 80-2SC - 2 Batteries - 80A [ARG080202000]

    Argodiode Battery Isolator 80-2SC - 2 Batteries - 80AArgodiode Battery Isolators allow simultaneous charging of two or more batteries from one alternator, without connecting the batteries. Discharging the accessory battery for example will not result in also discharging the starter battery. Low voltage drop due to the use of high-efficiency Schottky diodes.The Argo Battery Isolators feature a low voltage drop thanks to the use of Schottky diodes: at low current, the voltage drop is approximately 0,3 V, and at the rated output of approximately 0,45 V. All models are fitted with a compensation diode that can be used to slightly increase the output voltage of the alternator. This compensates for the voltage drop over the diodes in the isolator. Simply inserting the isolator in the cabling between the alternator and the batteries will slightly reduce charge voltage. The result can be that batteries are not charged to the full 100% and age prematurely. Alternator energize input Some alternators need DC voltage on the B+ output to start charging. Obviously, DC will be present when the alternator is directly connected to a battery. Inserting a Diode or FET splitter will however prevent any return voltage/current from the batteries to the B+, and the alternator will not start. The new ‘AC’ diode isolators feature a special current limited energize input that will power the B+ when the engine run/stop switch is closed.Please contact your dealer for any returns, repairs or support issues related to this product. Quick Guide (pdf)

    Read more

    $46.00 $39.10

You have seen 240 out of 345 products

Show more products

Victron Energy
Footer image

© 2025 REBELLION MARINE, Powered by Shopify

    Login

    Forgot your password?

    Don't have an account yet?
    Create account

    Add address