90° P-Trap Fuel Tank Vent -  Black with Black Vent HeadThis Attwood 90-Degree P-Trap Fuel Tank Vent reliably helps prevent water from entering the fuel tank while still allowing air to vent freely during normal sea conditions and washdowns. This vent’s effectiveness eliminates the need for an anti-siphon loop in the vent hose. It requires a ¾-inch installation hole and can be used with a maximum hull thickness of 9/16 inches.  Features: Standard Mount - (inch) 5/8" I.D Hose Reliably helps prevent water from entering the fuel tank Still allows air to vent freely during normal sea conditions and washdowns This black vent with a black vent head meets ABYC standards *Compatible with Ethanol blended fuels. Quick Guide (pdf)

Read more less

Grabber Catch Latch - Side Mount - Black - Pull-Up Force 44N (10lbf)Features: Spring-loaded over-center latching One assembly includes catch and keeper Material and Finish: PC/ABS, black Performance Details: Operating temperature range: -30ºC (-20ºF) to 60ºC (140ºF) Flammability rating: UL94-HB Installation Notes: Orient keeper to latch. The arrow on the keeper should point towards the cam. Mount to door and adjust for smooth latching. Minimum distance from frame (or surface on which catch subassembly is mounted) to centerline of door hinge is 150 (5.9)

Read more less

Mechanical Hatchlifter 12" STK FastThe AV hatch lifters are electromechanical products, especially designed for marine use on pleasure boats. They allow full or partial opening and closing of heavy engine hatches, peak tanks, hatch beams etc. By activating a switch, it is possible to lift the hatch to any desired position from closed to full open; an internal self-locking mechanism will maintain the position preventing any accidental hatch closing. In case of a power failure, an emergency device allows for manual opening.The Uflex AV hatch lifters do not require any maintenance, are easy to install, and are made of materials resistant.Features: According to the load required, the AV hatch lifter can be mounted individually, or in twin-cylinder installations for heavier loads. It is also possible to install more than two AV actuators in multiple applications.  Maximum load for single installations: 1200N (120 kg - 265 lbs)  Maximum load for dual installations: 2400N (240 kg - 529 lbs)  Maximum load is recommended not to be exceeded.  Supplied with all mounting hardware.  Stainless steel telescopic ram for manual operation in case of emergency.  Available on request without a manual emergency opening device for high-performance boats.  Circuit breaker to stop accidental overloading of the system and electronic stop at the closed or fully open position.  IP 65 protection rated  Speed: 25mm/sec no load applied, 17 mm/sec maximum load  Current absorption in single installations: 10A at 12V, 5A at 24V  Current absorption in dual installations: 20A at 12V, 10A at 24V  AV 12VDC models are Ignition Protected. UL1500 - ISO8846 approved. Specifications: Volt: 12V DC Stroke: 300mm (12") Length A (full closed actuator): 677 mm (26.6") Ø External: 48 mm (1.9")

Read more less

Door Catch Constructed of sturdy injection molded nylon. These Door Catches provide secure closure for cabinet doors. Installs with four #6 RH fasteners (not included). WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less

0591 Vented Fill f/1-1/2" Hose - Straight Neck - ChromeChrome Plated Bronze Cap Black Polymer Body Straight Neck & Heavy Duty Stainless Steel Bead Chain Integral Tank Vent with Flame Arrestor and Anti Surge Valve (on diesel only) Deck Plate Key Not Required *Note: Consider using the Mounting Ring (Fig. 0540DPRBLK) for all installations. DP package includes mounting ring. Technical Information For Hose Size: 1-1/2" For Vent Hose: 5/8" Mounting Hole Dia.: 2-1/8" O.D. Flange: 3-3/8" Neck Length: 2-7/16" Screw Size: #8

Read more less

Screw-Out Deck PlateThe Beckson Screw-Out Plate was designed to provide access without the use of tools, with a single start non-jamming (no cross-thread), extra strong, self-cleaning buttress thread. They incorporate a self-aligning center and an innovative gasket to assure a watertight seal. A back-up sealing wall leaves the plate watertight, even if the gasket is removed. Deck plates are used for access to shut-off valves or back-fastenings, inspection, and clean out for tanks and compartments. A screw-out plate should be used in compartments where a change in air pressure due to temperature or oil canning can occur. Center: Non-Skid Color: White

Read more less

Bow Eye - Machined 304 Stainless Steel - 7/16" x 3-1/2"These Bow Eyes are for use as a tie-down point on your boat’s bow. The 3/8" shafts have rolled threads. Constructed of corrosion-resistant machined 304 stainless steel. Includes adjustable finish nuts, which provide superior performance over crimp ring-style stern eyes. Can be used in conjunction with Lift Eyes (048330 or 048350) for a more robust lifting assembly.Specifications:Threads: 1/2" NC

Read more less

Door Hinge - 1-1/2" x 3" - Investment Cast 316 Stainless SteelThese Door Hinges are constructed of corrosion-resistant investment-cast 316 stainless steel. Installs with six #10 FH fasteners (not included).Specifications:Fastener: #10 FH Specifications: Material: Stainless Steel Box Dimensions: 1"H x 2"W x 3"L WT: 0.2 lbs

Read more less

Screw-Out Deck Plate - Black - 5" Sea-Dog® Screw-Out Deck Plates are molded to the highest standards using top quality UV stabilizers and antioxidants. When installing, use silicone sealant on hull or deck surface. Keep threads clean with hot, soapy water. Lubricate with Vaseline or Teflon grease.WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less

90° Gas Lift Mount - Wide 90° Gas Lift Mounts are constructed of stamped 304 stainless steel. Used for mounting gas filled lift springs. Installs with #10 RH fasteners (not included). 10 mm ball.WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less

Rigid Vinyl Flex-Core Rub Rail 2" x 7/8" - Black 60'TACO Marine’s latest Rub Rail innovation is an improved design of our most popular rigid PVC shape with a lightweight, high-density inner core. This allows for easier handling, faster one-piece installation, improved dimensional stability, and production run consistency.Features: Lightweight Easy handling and installation Solid, rigid PVC cap stock exhibits traditional surface characteristics, appearance, and impact properties Continuous coil eliminates butt joints around gunwale, with improved bending characteristics and the ability to cold form Vacuum calibration tooling allows for tighter dimensional tolerance and sizing consistency High-density core offers improved shock-absorbent impact resistance Made in the USA 5-year limited warranty Specifications: Color: Black Length: (feet) 60' Insert: S11-4511 required Drilled and countersunk for #8 screw on 8-inch centers This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns. Quick Guide (pdf)

Read more less

Flex Vinyl Rub Rail Kit - Black with Black Insert - 50' - 1-1/4"Excellent universal rub rail. Fits many different boat models. Convenient kit includes rub rail (in a continuous coil for one piece installation without seams), insert, end caps, screws and installation guideFeatures: 1-1/4"H x 15/16"W x 50'L Black with Black Insert This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns. Quick Guide (pdf)

Read more less

Flex Vinyl Rub Rail Kit - Black with Black Insert - 50' - 1-1/16"Excellent universal rub rail. Fits many different boat models. Convenient kit includes rub rail (in a continuous coil for one piece installation without seams), insert, end caps, screws and installation guide.Features: 1-1⁄16"H x 11⁄16"W x 50'L Black with Black Insert This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns. Quick Guide (pdf)

Read more less

Surface Mount & Latch - Black Body, Chrome Handle, Offset Cam Bar, 3/4" - 2-3/8"Features: Polymer body T Handle Stainless Steel Stem Lock with 2 keys Offset cam bar Easily Installs in a 2-1/2 Inch Diameter Hole for Mounting Surfaces 1/8 to 3/4 Inch Thick The T - Handle drops down flush in either the open or closed (180x Rotation) position. (except with the offset cam bar positioned upward) The rubber seal & boot under the T - Handle seals the lock cylinder preventing water intrusion Specs: Face Plate Diameter: 3" Body Color: Black Handle Color: Chrome Adjustment Cam Bar Inches: 3/4 - 2-3/8"

Read more less

Flush Pull Chrome Plated Zinc Alloy Black Polymer Finishing Flange Spring Loaded, Can be mounted Horizontally or Vertically

Read more less

2" Rub Rail End Cap - WhiteComplete your Rub Rail installation with our Rub Rail End Caps - available in white nylon for a secure fit.Features & Benefits: Cap the rail at the stern of the boat for a finished look Ensures inserts stay intact Sold individually Durable white nylon 5-year limited warranty Specifications: Width: 2" Color/Finish: White Profiles: V11-2423 & V11-3426

Read more less

Flush Pull Latch - Push To Close - Medium - BlackSpecifications: Material: Plastic Material Grade: PC / PBT Blend Finish: Natural Color/Appearance: Black Access Restriction: No Restriction Grip Range: 25.000-26.000 mm (0.98-1.02 in) Panel Thickness: 2.000-7.000 mm (0.08-0.28 in) Profile: Low Profile Size Series: Medium Size Southco offers modifications to our standard products, explore the possibilities of how Southco can engineer a solution to meet your specific application requirements.

Read more less

Flexible Draw LatchFeatures: Material: Rubber Material: Stainless Steel Finish: Natural Access Restriction: No Restriction Mounting Style: Front Mount Keeper Style: R Operation: Pull Series: 080 Series Latch Assembled: Yes

Read more less

Deck Fill for Carbon Canister System - Straight Body & Scalloped Chrome CapPressure relief systems are designed with automatic diurnal emission control and overpressure relief safety valves built into the cap of the fill. The overpressure relief safety valves are engineered to release pressure above 1 psi. The high-flow vacuum valves allow fresh air to enter the fuel tank to replace the fuel being consumed by the engine. Other components of a pressure relief system are designed to ensure the tank fills to the proper level every time without spit-back or well-back. Features: All Attwood pressure relief systems are designed to ensure water does not enter the fuel tank and are compatible with Jerry Can and marine nozzle refueling Fits 1-1/2 (inch) fill hose Designed and tested to prevent water from entering the fuel system Compatible with Ethanol blended fuels Chrome finish Automatic nozzle shutoff 4-18 gpm Dual 1 psi overpressure relief safety valves built into the deck fill caps EPA / CARB Certified Quick Guide (pdf)

Read more less

70' Flexible Black Rub Rail Insert 1-3/16" x 1/2"Hide Rub Rail fasteners and give your boat a clean look with the 1-3/16" X 1/2" Flexible Vinyl Insert.Features: For use with flexible Rub Rail Soft PVC insert provides cushion effect to absorb impact Made in the USA 5-year limited warranty Specifications: Length: 70' Color: Black Description: Flexible Vinyl, Black Rub Rail Insert, 1/2"W x 1-3/16"H x 70'L This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Read more less

PSS Shaft Seal 1-1/2" Shaft 2-1/2" TubeShaft Diameter: 1-1/2"Stern Tube Diameter (D): 2-1/2" to 2-5/8"Total Length (A): 9.175"Total Length (compressed) (Compressed A): 8.175"Rotor Diameter (B): 3.75"Carbon Cuff Diameter (C): 3.25"Stern Cuff Length (E): 2"The PSS Shaft Seal is the number one selling marine mechanical seal worldwide and is installed as standard equipment by many of the worlds most reputable boat builders / yards. The PSS Shaft Seal is also recognized as the premiere retrofit (aftermarket) seal on the world market. Certified by Bureau Veritas, ABS & Rina: Boat builders / yards recognize the advantages and value of installing the PSS as it eliminates the maintenance, constant adjustment & cost associated with traditional packing type glands. Aside from these benefits, the PSS Shaft Seal helps to eliminate water in the bilge (100% water tight) & wear to the propeller shaft. The PSS Shaft Seal can be easily retrofitted and is available for shafts ranging from 3/4" (20mm) to 6" (150mm).The PSS Shaft Seal is a mechanical face seal that is created between the flat surfaces of the rotating stainless steel rotor and the stationary carbon flange. The stationary carbon flange is attached to the vessels stern tube with hose clamps and the carbon flange is attached to the front side of the bellows with hose clamps. The stainless steel rotor is fit on the shaft in front of the carbon flange. The stainless steel rotor is used to compress the bellows before the collar is secured to the shaft with set-screws. This compression (pre-load) maintains contact between the faces and allows the PSS to compensate for the thrust from the propeller. The carbon flange is bored larger than the shaft diameter allowing it to "float" around the shaft and thus compensate for most misalignment and vibration problems. The stainless steel collar is sealed to the shaft by two o-rings that are recessed into the bore of the collar. These o-rings rotate with the shaft and stainless steel rotor and do not experience wear during operation.**As with any rubber hose below waterline, the PSS bellows must be inspected on a regular basis for any sign of wear, aging or chemical deterioration. PYI suggests as preventative maintenance that the PSS bellow be replaced in six year intervals. During bellows replacement it is recommended the o-rings & set screws in the stainless steel rotor also be replaced."Bellows may need to be more frequently inspected in an environment where non-sealed batteries emit sulfuric acid. Sulfuric acid vapor will accelerate rubber deterioration, as will an ozonater.The Maintenance Kit includes the items you need to properly maintain your PSS Shaft Seal. Included in the kit is one (1) PSS bellow, two (2) O-rings, five (5) set screws, four (4) new hose clamps and an allen key. Brochure (pdf)

Read more less

170 Finger Grip Destroyer 5-Spoke 15.5" Stainless Steel Cap 3/4" Tapered Shaft with KnobThe Destroyer Wheel is a 5-spoke stainless steel steering wheel that can be a great addition to any boat. This specific steering wheel comes with a fitted black center cap.Features: Destroyer Wheel 6 spoke Standard rim Back center cap 10-degree dish Fits a 1" straight shaft

Read more less

Screw-Out Deck PlateThe Beckson Screw-Out Plate was designed to provide access without the use of tools, with a single start non-jamming (no cross-thread), extra strong, self-cleaning buttress thread. They incorporate a self-aligning center and an innovative gasket to assure a watertight seal. A back-up sealing wall leaves the plate watertight, even if the gasket is removed. Deck plates are used for access to shut-off valves or back-fastenings, inspection, and clean out for tanks and compartments. A screw-out plate should be used in compartments where a change in air pressure due to temperature or oil canning can occur. Center: Smooth Color: Beige

Read more less

Stud Catch Length: 2-1/4" Width: 7/16" Fastener: #8(4) Material: Brass Quick Guide (pdf)

Read more less

14" x 24" Flush Hatch White - ASA Material - Acrylonitrile Styrene AcrylateFeatures: 1/2” Closed Height Weather-tight Seal Opens full 180 degrees Nothing to Snag Lines One-Hand Operation Mounts Vertical or Horizontal UV Stabilized Material Invisible Fasteners Color: White Non-Skid Diamond Pattern Surface

Read more less

Teak Drinkholder with Removable Cockpit Table Top - Holds 4 GlassesFeatures: Table Top Dimensions: 16" x 24" Drinkholder holds four glasses Can be used without table Fits all 7/8" or 1" diameter tubing pedestal steering guards Easily removed

Read more less

Screw-Out Deck PlateThe Beckson Screw-Out Plate was designed to provide access without the use of tools, with a single start non-jamming (no cross-thread), extra strong, self-cleaning buttress thread. They incorporate a self-aligning center and an innovative gasket to assure a watertight seal. A back-up sealing wall leaves the plate watertight, even if the gasket is removed. Deck plates are used for access to shut-off valves or back-fastenings, inspection, and clean out for tanks and compartments. A screw-out plate should be used in compartments where a change in air pressure due to temperature or oil canning can occur. Center: White Color: Beige

Read more less

TCL4 9" Locker Door - BlackKeep storage areas dry with this tried, tested, and trusted black Whale locker door/deck hatch.Features:Reliable watertight sealMeasurements: Diameter: 228 mm (9 in.) Aperture: 179 mm (7 in.) Materials: Body: Polycarbonate Locking Ring: Acetal  Seal: Nitrile Specifications: Color: Black Box Dimensions: 2"H x 10"W x 10"L WT: 1 lbs UPC: 766478400000

Read more less

Slam LatchIncludes Striker PlateStainless SteelFlange:2-3/8"Depth:1-1/2"Fastener: Provided

Read more less

Deck Fill for Pressure Relief Systems - Angled Body & Scalloped Black Plastic CapPressure relief systems are designed with automatic diurnal emission control and overpressure relief safety valves built into the cap of the fill. The overpressure relief safety valves are engineered to release pressure above 1 psi. The high-flow vacuum valves allow fresh air to enter the fuel tank to replace the fuel being consumed by the engine. Other components of a pressure relief system are designed to ensure the tank fills to the proper level every time without spit-back or well-back. All Attwood pressure relief systems are designed to ensure water does not enter the fuel tank and are compatible with Jerry Can and marine nozzle refueling.Features: Fits 1-1/2 (inch) fill hose and 5/8 (inch) vent hose Triple high-flow vacuum valves ensure maximum make-up airflow (compatible with high HP applications) Dual 1 psi diurnal emission control and overpressure relief safety valves built into the cap Automatic nozzle shutoff 4-18 gpm Black Composite finish An essential component of VaporTec and SecureStop Designed and tested to prevent water from entering the fuel system EPA / CARB Certified Hinged audible click cap meets EPA requirements Meets CARB 13 CCR 2235 and ISO 13331 nozzle mating and retention standards *Compatible with Ethanol blended fuels Quick Guide (pdf)

Read more less

Compression Handle Replacement KeyMolded Key for Hexagonal Lock Fits: 6136, 6236, 6738, S-0251, S-0336, S-0436, S-0536.

Read more less

Dish/Cup Holder Holds 4 each of plates and cups 19-3/4" L x 4-1/4" D x 11-1/2" H

Read more less

Teak Deck Steps8-3/4"L x 3-1/2"W x 1/2"H

Read more less

Swivel Eye Hasp - 3" - Chrome PlatedZincFeatures: Chrome Plated Zinc Alloy Padlock eye swivels to act as a latch Specs: Closed Length: 3" Width: 1" Padlock Clearance: 11/32" Screw Size: 6

Read more less

Cowl Ventilator(0870) Chrome Plated Zinc Alloy Cowl with Black PERKO-KOTE Base 3" Duct Thread into Neck, Hose Clamps Not Required Cowl Opening Square: 7-1/3"

Read more less

Flex Vinyl Rub Rail Kit - Black with Black Insert - 70' - 1-1/16" x 11/16"Excellent universal rub rail. Fits many different boat models. Convenient kit includes rub rail (in a continuous coil for one piece installation without seams), insert, end caps, screws and installation guide.Features: Rub Rail Kit Vinyl 70' 1-1/16" x 11/16" Black with Black Insert This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns. Quick Guide (pdf)

Read more less

Pipe Deck Fill - 1-1/2" - WaterFeatures: 316 S.S. 1-1/2" Pipe Water Deck Fill with Key Chain included Flange: 3-3/8" Fastener: #10 (3) Weight: 20oz Replacement cap & chain is P/N 6074

Read more less

Flush Mount 2-Pin HingeLength:3"Width:1-1/2"Depth:3/8"Fastener:#8(6)Material: 304 Stainless Steel Specifications: Material: Stainless Steel Color: Stainless Box Dimensions: 1"H x 2"W x 3"L WT: 0.17 lbs UPC: 725060370015

Read more less

TCL2 9" Locker Door - Diecast AluminumKeep storage areas dry with this tried, tested, and trusted aluminum Whale locker door/deck hatch.Features: Robust aluminum construction with a locking lever  Ideal for harsh marine environments Measurements: Diameter: 228 mm (9 in.) Aperture: 179 mm (7 in.) Materials: Body: Diecast aluminum alloy Seal: Nitrile Specifications: Color: Aluminum Box Dimensions: 3"H x 9"W x 9"L WT: 2.2 lbs UPC: 766478200006

Read more less

Polished Stainless Steel 2-19/64’’ Rub Rail End CapCaps rub rail to finish end of rail and ensure that inserts stay intact.Features: Caps rub rail to finish end of rail Ensures inserts stay intact Offers a finished look Stainless Steel Marine Grade 316 Polished 5-Year limited warranty This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Read more less

Gas Tank Strap - Nylon Webbing/304 Stainless Steel - 72"This Gas Tank Strap is for use in securing a portable gas tank. Includes: 1” x 6’ webbing strap with buckle, two footman's loops, and four #10 FH fasteners. Constructed of nylon webbing with corrosion-resistant 304 stainless steel hardware.Specifications:Fastener: #10 FH Specifications: Type: Parts Box Dimensions: 3"H x 4"W x 7"L WT: 0.35 lbs UPC: 035514359030

Read more less

Push Button Rim Latch - Square - Stainless Steel/Plastic HousingPush Button Rim Latch housings feature a streamlined, positive-action closure, ensuring cabinets and drawers stay closed until the button is deliberately pushed. Suitable for left-side or right-side use. Mortise mount for a sleek, finished appearance. Constructed of sturdy plastic with a corrosion resistant 304 stainless steel knob. Latch installs with two #6 RH fasteners, strike plates require two #4 FH fasteners (fasteners not included). Display version comes with both flat and 90° strike plates for inset or overlay mounting. When ordering bulk, please order strike plates (224320 flat, or 224321 90°) separately. Hole spacing on flat strike plate (224320) is 1-7/8". Hole spacing on 90° strike plate (224321) is 1-3/16". For OEM applications, varying combinations of rosettes/buttons are available.Specifications: Finish: Stainless Fastener: #6 RH

Read more less

Locking Push Button LatchFeatures: Cut-Out: 1” Use for door/hatch where want to use forefinger and thumb to open Locking Great for glove boxes, electronic boxes, plexiglass doors

Read more less

T-Handle Latch Key ReplacementReplacement Key for Part Numbers: S-226B, S-226W, S-226BLS, 3226B

Read more less

Gas Filled Lift Spring - 10" - 40# Sea-Dog® Gas Springs and hardware are manufactured to marine OE standards and have been installed in marine and RV applications for several years. You can count on our high quality and a 2-year warranty on all Sea-Dog® Gas Springs. Sea-Dog® Gas Springs are the ideal choice for all marine, RV, truck cap, tool box, and utility applications because of their unique multi-lobe seal which offers superior service life and performance. Hard chromium plated shafts, bronze bushings, and polymer end fittings mean you are buying THE BEST. Other applications for Sea-Dog® Gas Springs: Hatches, doors, tool boxes, farm machinery, golf carts, luggage doors, engine hatches, canopies, access hatches, seating, RV doors, furniture, truck caps, and utility boxes. Accepts 10 mm ball.WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Length: 10" Lift Capacity: 40 lbs Box Dimensions: 1"H x 1"W x 11"L WT: 0.25 lbs UPC: 035514321785

Read more less

Screw-Out Deck PlateThe Beckson Screw-Out Plate was designed to provide access without the use of tools, with a single start non-jamming (no cross-thread), extra strong, self-cleaning buttress thread. They incorporate a self-aligning center and an innovative gasket to assure a watertight seal. A back-up sealing wall leaves the plate watertight, even if the gasket is removed. Deck plates are used for access to shut-off valves or back-fastenings, inspection, and clean out for tanks and compartments. A screw-out plate should be used in compartments where a change in air pressure due to temperature or oil canning can occur. Center: Smooth Color: White

Read more less

Torcello 14" Wheel - 03 Series - Polyurethane Wheel with Chrome Spoke Inserts & Cap - Black Brushed Spokes - 3/4" - Retail PackagingThe 03 Series Torcello Wheel is a black polyurethane steering wheel with brushed spokes. Best suited for ski boats, wakeboard boats, runabouts, or pontoons that run in freshwater applications.This particular steering wheel comes in retail packaging.Features: Torcello Wheel 03 Series Socket head screws The wheel is made of polyurethane Chrome cap and spoke trim Black brushed spokes 3 spokes Specifications: Rim Diameter (inch): 14" Hole Diameter (inch): 3/4" tapered hub Specifications: Diameter (Inches): 14 Box Dimensions: 4"H x 15"W x 15"L WT: 3.6 lbs UPC: 835719003529 Quick Guide (pdf)Brochure (pdf)

Read more less

EPA Pull-UP Deck Fill - 30° - Angled - 1-1/2" - GasFeatures: Type - Gas 30 Degrees Flange - 3" Hose - 1-1/2" Angle - 30 degree Chain - yes Fastener - #10 (3) 316 Stainless Steel 1/4" turn pull-up cap with safety chain EPA approved for audible/visual open/close of cap Color coded and imprinted with international standard symbols

Read more less